300Mbps Wireless-N Broadband Router

User Manual

45

Figure 4-33

AP1:



Select radio mode is

‘

Access Point

’

in wireless management-basic of AP1.



Select Channel is

‘

Channel 6

’

in wireless management-basic of AP1.

Figure 4-34

AP2:



Select radio mode is

‘

REPEATER

’

in wireless management-basic of AP2.



Click

‘

AP Scan

’

in wireless management-basic of AP2 ,and select

‘

Netis1

’

and Connect ,

then the

‘

Repeater SSID

’

and

‘

Channel

’

become same as AP1.



The IP address of AP2 should be 192.168.1.x (1<x<255,e.g.: x=8).

300Mbps Wireless-N Broadband Router

User Manual

46



Select

‘

LAN setup

’

-

‘

DHCP server

’

,select disable DHCP server.

Figure 4-35

AP3:



Select radio mode is

‘

REPEATER

’

in wireless management-basic of AP3.



Click

‘

AP Scan

’

in wireless management-basic of AP3 ,and select

‘

Netis1

’

and Connect ,

then the

‘

Repeater SSID

’

and

‘

Channel

’

become same as AP2.



The IP address of AP3 should be 192.168.1.x (1<x<255),but different from AP2.



Select

‘

LAN setup

’

-

‘

DHCP server

’

,select disable DHCP server.

4.5.6.

Wireless Advanced

These settings are only for more technically advanced users who have a sufficient knowledge

about wireless LAN. These settings should not be changed unless you know what effect the

change will have on your AP.

300Mbps Wireless-N Broadband Router

User Manual

47

Figure 4-36



Authentications type:

The default is set to “Auto”, which allows “Open System” or

“Shared Key” authentication to be used. Select “Shared Key” if you only want to use

“Shared Key” authentication (the sender and recipient use a WEP key for authentication)

.



Beacon Interval: The interval time of this 150Mbps Wireless-N Broadband Router

broadcast a beacon. Beacon is used to synchronize the wireless network. The valid interval

is 20-1000, the default is 100.



RTS Threshold: You can set RTS Threshold value in this field, the valid range should be

256-2347 and default value is 2347. If a network packet is smaller than the preset RTS

threshold size, the RTS/CTS mechanism will not be enabled.



Aggregation: You can accelerate the wireless transmission speed by enabling the

aggregation function. The default is AMPDU

＋

AMSDU.



Fragmentation Threshold: It specifies the maximum size of packet during the

fragmentation of data to be transmitted.



Transmission Rate: Transmit rate indicates the transmission speed of wireless LAN

access .The default setting is “Auto” and you can set this value between 1

-54Mbps range.



ShortGi: You can select

“

Enable

”

or

“

disable

”

for shortgi.



Protection: Using 802.11b and 802.11g mixed mode may result in poor network

performance. By enabling 802.11 protection, it will ameliorate performance of 802.11g

devices in your wireless network.

300Mbps Wireless-N Broadband Router

User Manual

48



Preamble Type: "Short Preamble" is suitable for heavy traffic wireless network. "Long

Preamble" provides much communication reliability; the default setting is "Long

Preamble”

.

4.5.7.

Wireless Statistics

Display current status of the wireless client associate with AP.

Figure 4-37

4.5.8.

Multiple AP Settings

The default status of secondary AP is disable, you can select enable to enable the secondary

AP. Please refer to

Quick Setup Wireless Security

and

Wireless Statistics

for details.

Figure 4-38

300Mbps Wireless-N Broadband Router

User Manual

49

4.6.

DHCP

4.6.1.

DHCP Settings

Figure 4-39



DHCP Server Status: Keep the

default setting “Enable”, so router is able to use DHCP

function. If a DHCP

server has already existed in the network, please select “Disable”.



Start IP Address: The IP Address is used for allocate IP address by DHCP server; enter the

start IP address.



End IP Address: The IP Address is used for allocate IP address by DHCP server; enter the

end IP address.

4.6.2.

DHCP Clients List

Display the state of assigned IP by DHCP Server.

Figure 4-40