NETGEAR WNR2000v2 Router Manual PDF (Setup & Configuration Guide)

Page 21 / 144 Scroll up to view Page 16 - 20

NETGEAR Wireless-N 300 Router WNR2000v2 User Manual

Configuring Basic Connectivity

1-8

v1.0, January 2010

–

Account Name

(might also be called Host Name). The account name is provided to the

ISP during a DHCP request from your router. In most cases, this setting is not required,

but some ISPs require it for access to ISP services such as mail or news servers.

–

Domain Name

. The domain name is provided by your router to computers on your LAN

when the computers request DHCP settings from your router. In most cases, this settings is

not required.

–

Internet IP Address

. Determines how your router obtains an IP address for Internet

access.

•

If your ISP assigns an IP address dynamically (by DHCP), select

Get Dynamically

From ISP

.

•

If your ISP has assigned you a permanent, fixed (static) IP address for your computer,

select

Use Static IP Address

. Enter the IP address that your ISP assigned. Also, enter

the subnet mask and the gateway IP address. The gateway is the ISP’s router to which

your router will connect.

–

Domain Name Server (DNS) Address

. If you know that your ISP does not automatically

transmit DNS addresses to the router during login, select

Use These DNS Servers

, and

enter the IP address of your ISP’s primary DNS server. If a secondary DNS server address

is available, enter it also.

–

Router MAC Address

. This section determines the Ethernet MAC address that the router

will use on the Internet port. Typically, you would leave

Use Default Address

selected.

However, some ISPs (especially cable modem providers) register the Ethernet MAC

address of the network interface card in your computer when your account is first opened.

They then accept only traffic from the MAC address of that computer. This feature allows

your router to masquerade as that computer by “cloning” or “spoofing” its MAC address.

To change the MAC address, select one of the following methods:

•

Select

Use Computer MAC Address

. The router will then capture and use the MAC

address of the computer that you are now using. You must be using the one computer

that is allowed by the ISP.

•

Select

Use This MAC Address

, and enter it here.

Note:

If you enter or change a DNS address, restart the computers on your

network so that these settings take effect.

Page 22 / 144

NETGEAR Wireless-N 300 Router WNR2000v2 User Manual

Configuring Basic Connectivity

1-9

v1.0, January 2010

If a login is required by your ISP, the following settings appear in the Basic Settings screen:

•

Does Your Internet Connection Require A Login?

If you usually must use a login program

such as WinPOET to access the Internet, your Internet connection requires a login. After you

select

Yes

, the Basic Settings screen displays.

–

Internet Service Provider

. This drop-down list contains a few ISPs that need special

protocols for connection. The list includes:

•

PPTP

(Point to Point Tunneling Protocol), used primarily in Austrian DSL services

Figure 1-7

Note:

After you finish setting up your router, you will no longer need to launch the

ISP’s login program on your computer to access the Internet. When you start

an Internet application, your router will automatically log you in.

ISP

does

require login

Page 23 / 144

NETGEAR Wireless-N 300 Router WNR2000v2 User Manual

Configuring Basic Connectivity

1-10

v1.0, January 2010

•

Telstra Bigpond

, an Australian residential cable modem service

•

Other

, which selects PPPoE (Point to Point Protocol over Ethernet), the protocol used

by most DSL services worldwide.

–

Login and Password

. This is the user name and password provided by your ISP. This

name and password are used to log in to the ISP server.

–

Service Name

. If your connection is capable of connecting to multiple Internet services,

this setting specifies which service to use.

•

Connection Mode

. This drop-down list selects when the router will connect to and

disconnect from the Internet.

Note:

The Telstra Bigpond setting is only for older cable modem service

accounts still requiring a Bigpond login utility. Telstra has

discontinued this type of account. Those with Telstra DSL accounts

and newer cable modem accounts should select

No

for Does Your

Internet Connection Require a Login.

Figure 1-8

Note:

Not all ISPs are listed here. The ones on this list have special

requirements.

Figure 1-9

Page 24 / 144

NETGEAR Wireless-N 300 Router WNR2000v2 User Manual

Configuring Basic Connectivity

1-11

v1.0, January 2010

–

The list includes:

•

Always On

. The router logs in to the Internet immediately after booting and never

disconnects.

•

Dial on Demand

. The router logs in only when outgoing traffic is present and logs out

after the idle time-out.

•

Manually Connect

. The router logs in or logs out only when the user clicks

Connect

or

Disconnect

in the Router Status screen.

–

Idle Timeout

. Your Internet connection is logged out if there is no data transfer during the

specified time interval.

–

Domain Name Server (DNS) Address

. If you know that your ISP does not automatically

transmit DNS addresses to the router during login, select

Use These DNS Servers

, and

enter the IP address of your ISP’s primary DNS server. If a secondary DNS server address

is available, enter it also.

Setting Up and Testing Basic Wireless Connectivity

Follow these instructions to set up and test basic wireless connectivity. Once you have established

basic wireless connectivity, you can enable security settings appropriate to your needs.

Note:

If you enter or change a DNS address, restart the computers on your

network so that these settings take effect.

Note:

If you use a wireless computer to change wireless settings, you might be

disconnected when you click

Apply

. Reconfigure your wireless adapter to match

the new settings, or access the router from a wired computer to make any further

changes.

Page 25 / 144

NETGEAR Wireless-N 300 Router WNR2000v2 User Manual

Configuring Basic Connectivity

1-12

v1.0, January 2010

1.

Select

Wireless Settings

under Setup in the main menu of the WNR2000v2 router.

2.

For the wireless network name (SSID), use the default name, or choose a suitable descriptive

name. In the

Name (SSID)

field, you can enter a value of up to 32 alphanumeric characters.

The default SSID is NETGEAR.

3.

Select the region in which the wireless interface will operate.

4.

Set the channel. The default channel is

Auto

.

This field determines which operating frequency is used. It should not be necessary to change

the wireless channel unless you notice interference problems with another nearby wireless

router or access point. Select a channel that is not being used by any other wireless networks

within several hundred feet of your router. For more information about the wireless channel

frequencies, click the link to the online document

“Wireless Networking Basics” in

Appendix B

.

5.

Make sure that the mode is set to

Up to 145Mbps

.

Figure 1-10

Note:

The SSID is case-sensitive; NETGEAR is not the same as nETgear. Also, the

SSID of any wireless access adapters must match the SSID you specify in the

WNR2000v2 router. If they do not match, you will not get a wireless

connection to the WNR2000v2 router.

Rate

Popular NETGEAR Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share