1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WNDR3700v4
    5. /
  5. 3
Page 11 / 115 Scroll up to view Page 6 - 10
11
N600 Wireless Dual Band Gigabit Router WNDR3700v4
Attach the Stand
For optimal wireless network performance, use the stand (included in the package) to
position your router upright.
1.
Orient your router vertically.
2.
Insert the tabs of the stand into the slots on the bottom of your router as shown.
Place your router in a suitable area for installation (near an AC power outlet and accessible to the
Ethernet cables for your wired computers).
Position Your Router
The router lets you access your network from virtually anywhere within the operating range of
your wireless network. However, the operating distance or range of your wireless connection
can vary significantly depending on the physical placement of your router. For example, the
thickness and number of walls the wireless signal passes through can limit the range. For
best results, place your router:
•
Near the center of the area where your computers and other devices operate, and
preferably within line of sight to your wireless devices.
•
So it is accessible to an AC power outlet and near Ethernet cables for wired computers.
•
In an elevated location such as a high shelf, keeping the number of walls and ceilings
between the router and your other devices to a minimum.
Page 12 / 115
12
N600 Wireless Dual Band Gigabit Router WNDR3700v4
•
Away from electrical devices that are potential sources of interference, such as ceiling
fans, home security systems, microwaves, computers, or the base of a cordless phone or
2.4-GHz cordless phone.
•
Away from any large metal surfaces, such as a solid metal door or aluminum studs. Large
expanses of other materials such as glass, insulated walls, fish tanks, mirrors, brick, and
concrete can also affect your wireless signal.
•
With the antennas in a vertical position to provide the best side-to-side coverage or in a
horizontal position to provide the best up-and-down coverage, as applicable.
Cable Your Router
The installation guide that came in the box has a cabling diagram on the first page. This
section walks you through cabling with detailed illustrations.
1.
Connect the router, the computer, and the modem.
2.
Turn off and unplug the modem. If your modem has a backup battery, remove it as well.
Internet
DSL or cable
Modem
3.
Locate the Ethernet cable (
1
) that connects your computer to the modem.
1
2
Page 13 / 115
13
N600 Wireless Dual Band Gigabit Router WNDR3700v4
4.
Disconnect the cable from the modem (
2
). You will connect it to the router later.
5.
Locate the Ethernet cable that came with the NETGEAR product. Securely insert that
Ethernet cable into your modem and into the Internet port of the router (
3
).
3
6.
Locate the cable you removed from the modem in step 2. Securely insert that cable (
4
) into
a LAN port on the router such as LAN port 1.
4
7.
Your network cables are connected, and you are ready to start your network. It is important
that you start your network in the correct sequence (first power on the modem, and after it
finishes starting up, power on the router).
Verify the Cabling
Verify that your router is cabled correctly by checking the router LEDs. Turn on the router by
pressing the
On/Off
button on the back.
•
The Power LED lights amber when the router is turned on.
•
The LAN port LEDs light green for each computer that is cabled to the router.
•
The 2.4 GHz N/G-Band LED is lit, and the 5.0 GHz N-Band LED is lit.
•
The Internet LED is lit. If it is not, make sure that the Ethernet cable is securely
attached to the router Internet port and the modem, and that the modem is powered on.
Verify that the LAN
LEDs (1 through 4) are lit for any computers cabled to the router by
an Ethernet cable.
Page 14 / 115
14
2
2.
Getting Started with NETGEAR genie
Connecting the router
This chapter explains how to use NETGEAR genie to set up your router after you complete
cabling as described in the installation guide and in the previous chapter.
This chapter contains the following sections:
•
Router Setup Preparation
•
Types of Logins and Access
•
Use NETGEAR genie after Installation
•
Upgrade the Firmware
•
Dashboard (Basic Home Screen)
•
Join Your Wireless Network
•
NETGEAR genie App and Mobile genie App
Page 15 / 115
Getting Started with NETGEAR genie
15
N600 Wireless Dual Band Gigabit Router WNDR3700v4
Router Setup Preparation
You can allow NETGEAR genie to automatically set up your router, or you can use the genie
menus and screens to set up your router manually. Before you start the setup process, get
your ISP information and make sure the computers and devices in the network have the
settings described here.
Use Standard TCP/IP Properties for DHCP
If you set up your computer to use a static IP address, you need to change the settings so
that it uses Dynamic Host Configuration Protocol (DHCP). Consult the documentation that
came with your computer or operating system for instructions about how to do this.
Gather ISP Information
If you have DSL broadband service, you might need the following information to set up your
router and to check that your Internet configuration is correct. Your Internet service provider
(ISP) should have provided you with all of the information needed to connect to the Internet.
If you cannot locate this information, ask your ISP to provide it. When your Internet
connection is working, you no longer need to launch the ISP login program on your computer
to access the Internet. When you start an Internet application, your router automatically logs
you in. Make sure that you have the following information:
•
The ISP configuration information for your DSL account
•
ISP login name and password
•
Fixed or static IP address settings (special deployment by ISP; this is rare)
Wireless Devices and Security Settings
Make sure that the wireless device or computer that you are using supports WPA or WPA2
wireless security, which is the wireless security supported by the router.
Types of Logins and Access
Different types of logins have different purposes: It is important that you understand the
difference so that you know which login to use when.
•
Router login
logs you in to the router interface from NETGEAR genie. See
Use
NETGEAR genie after Installation
on page
16 for details about this login.
•
ISP login
logs you in to your Internet service. Your service provider has provided you with
this login information, typically in a letter. If you cannot find this login information, contact
your service provider.
•
WiFi password
. The preset SSID (WiFi network name) and preset WiFi password for
your router are unique. This information is on the label on the bottom of your router.

Rate

4 / 5 based on 1 vote.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top