Page 91 / 178 Scroll up to view Page 86 - 90
Reference Manual for the Double 108 Mbps Wireless Firewall Router WGU624
Advanced Configuration
7-13
M-10153-01
To configure Dynamic DNS:
1.
Register for an account with DynDNS.org. Select “Click here for information” to go to
www.dyndns.org
.
2.
Select DynDNS.org.
3.
Type the Host Name appended with dyndns.org. For example:
myHostName.dyndns.org
4.
Type the User Name for your dynamic DNS account.
5.
Type the Password (or key) for your dynamic DNS account.
6.
If you want to allow the use of wildcards in resolving your URL, you can select the Use
wildcards check box to activate this feature. For example, the wildcard feature will cause
*.yourhost.dyndns.org to be aliased to the same IP address as yourhost.dyndns.org
7.
Click Apply to save your configuration.
Configuring Static Routes
Static Routes provide additional routing information to your router. Under normal circumstances,
the router has adequate routing information after it has been configured for Internet access, and
you do not need to configure additional static routes. You must configure static routes only for
unusual cases such as multiple routers or multiple IP subnets located on your network.
From the main menu of the browser interface, under Advanced, select Static Routes to view the
Static Routes menu, shown below.
Figure 7-6.
Static Routes menu
Page 92 / 178
Reference Manual for the Double 108 Mbps Wireless Firewall Router WGU624
7-14
Advanced Configuration
M-10153-01
To add or edit a Static Route:
1.
Click the Add button to open the Add/Edit menu, shown below.
Figure 7-7.
Static Route Add/Edit menu
2.
Type a route name for this static route in the Route Name box under the table. (This is for
identification purposes only.)
3.
Select Private if you want to limit access to the LAN only. The static route will not be reported
in RIP.
4.
Select Active to make this route effective.
5.
Type the Destination IP Address of the final destination.
6.
Type the IP Subnet Mask for this destination. If the destination is a single host, type
255.255.255.255.
7.
Type the Gateway IP Address, which must be a router on the same LAN segment as the router.
8.
Type a number between 1 and 15 as the Metric value. This represents the number of routers
between your network and the destination. Usually, a setting of 2 or 3 works, but if this is a
direct connection, set it to 1.
9.
Click Apply to have the static route entered into the table.
Page 93 / 178
Reference Manual for the Double 108 Mbps Wireless Firewall Router WGU624
Advanced Configuration
7-15
M-10153-01
Static Route Example
As an example of when a static route is needed, consider the following case:
Your primary Internet access is through a cable modem to an ISP.
You have an ISDN router on your home network for connecting to the company where
you are employed. This router’s address on your LAN is 192.168.1.100.
Your company’s network is 134.177.1.0.
When you first configured your router, two implicit static routes were created. A default route was
created with your ISP as the gateway, and a second static route was created to your local network
for all 192.168.1.x addresses. With this configuration, if you attempt to access a device on the
134.177.1.0 network, your router forwards your request to the ISP. The ISP forwards your request
to the company where you are employed, and the request will likely be denied by the company’s
firewall.
In this case you must define a static route, telling your router that 134.177.1.0 should be accessed
through the ISDN router at 192.168.1.100. The static route would look like
Figure 7-7
.
In this example:
The Destination IP Address and IP Subnet Mask fields specify that this static route applies to
all 134.177.1.x addresses.
The Gateway IP Address fields specifies that all traffic for these addresses should be
forwarded to the ISDN router at 192.168.1.100.
A Metric value of 1 will work since the ISDN router is on the LAN.
Private is selected only as a precautionary security measure in case RIP is activated.
Page 94 / 178
Reference Manual for the Double 108 Mbps Wireless Firewall Router WGU624
7-16
Advanced Configuration
M-10153-01
Enabling Remote Management Access
Using the Remote Management page, you can allow a user or users on the Internet to configure,
upgrade and check the status of your WGU624 wireless router.
To configure your router for Remote Management:
1.
Select the Turn Remote Management On check box.
2.
Specify what external addresses will be allowed to access the router’s remote management.
Note:
For enhanced security, restrict access to as few external IP addresses as practical.
To allow access from any IP address on the Internet, select Everyone.
To allow access from a range of IP addresses on the Internet, select IP address range.
Enter a beginning and ending IP address to define the allowed range.
To allow access from a single IP address on the Internet, select Only this PC.
Enter the IP address that will be allowed access.
3.
Specify the Port Number that will be used for accessing the management interface.
Web browser access normally uses the standard HTTP service port 80. For greater security,
you can change the remote management Web interface to a custom port by entering that
number in the box provided. Choose a number between 1024 and 65535, but do not use the
number of any common service port. The default is 8080, which is a common alternate for
HTTP.
4.
Click Apply to have your changes take effect.
Note:
When accessing your router from the Internet, you will type your router's WAN IP address
into your browser's Address (in IE) or Location (in Netscape) box, followed by a colon (:) and the
custom port number. For example, if your external address is 134.177.0.123 and you use port
number 8080, you must enter
in your browser.
Note:
Be sure to change the router's default configuration password to a very secure
password. The ideal password should contain no dictionary words from any language,
and should be a mixture of letters (both upper and lower case), numbers, and symbols.
Your password can be up to 30 characters.
Page 95 / 178
Reference Manual for the Double 108 Mbps Wireless Firewall Router WGU624
Advanced Configuration
7-17
M-10153-01
Using Universal Plug and Play (UPnP)
Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers,
access the network and connect to other devices as needed. UPnP devices can
automatically discover the services from other registered UPnP devices on the network.
Figure 7-8.
UPnP Menu
Turn UPnP On:
UPnP can be enabled or disabled for automatic device configuration. The default
setting for UPnP is enabled. If disabled, the router will not allow any device to automatically
control the resources, such as port forwarding (mapping), of the router.
Advertisement Period
: The Advertisement Period is how often the router will broadcast its UPnP
information. This value can range from 1 to 1440 minutes. The default period is 30 minutes.
Shorter durations will ensure that control points have current device status at the expense of
additional network traffic. Longer durations may compromise the freshness of the device status
but can significantly reduce network traffic.
Advertisement Time To Live
: The time to live for the advertisement is measured in hops (steps)
for each UPnP packet sent. The time to live hop count is the number of steps a broadcast packet is
allowed to propagate for each UPnP advertisement before it disappears. The number of hops can
range from 1 to 255. The default value for the advertisement time to live is 4 hops, which should
be fine for most home networks. If you notice that some devices are not being updated or reached
correctly, then it may be necessary to increase this value a little.

Rate

4.3 / 5 based on 3 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top