1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WGT634U
    5. /
  5. 25
Page 121 / 180 Scroll up to view Page 116 - 120
Reference Manual for the 108 Mbps Wireless Media Router WGT634U
Network, Routing, Firewall, and Basics
B-9
April 2004, 202-10018-02
If a device sends data to another station on the network and the destination MAC address is not yet
recorded, ARP is used. An ARP request is broadcast onto the network. All stations on the network
receive and read the request. The destination IP address for the chosen station is included as part of
the message so that only the station with this IP address responds to the ARP request. All other
stations discard the request.
Related Documents
The station with the correct IP address responds with its own MAC address directly to the sending
device. The receiving station provides the transmitting station with the required destination MAC
address. The IP address data and MAC address data for each station are held in an ARP table. The
next time data is sent, the address can be obtained from the address information in the table.
For more information about address assignment, refer to the IETF documents RFC 1597,
Address
Allocation for Private Internets,
and RFC 1466,
Guidelines for Management of IP Address Space
.
For more information about IP address translation, refer to RFC 1631,
The IP Network Address
Translator (NAT)
.
Domain Name Server
Many of the resources on the Internet can be addressed by simple descriptive names such as
www.NETGEAR.com
. This addressing is very helpful at the application level, but the descriptive
name must be translated to an IP address in order for a user to actually contact the resource. Just as
a telephone directory maps names to phone numbers, or as an ARP table maps IP addresses to
MAC addresses, a domain name system (DNS) server maps descriptive names of network
resources to IP addresses.
When a PC accesses a resource by its descriptive name, it first contacts a DNS server to obtain the
IP address of the resource. The PC sends the desired message using the IP address. Many large
organizations, such as ISPs, maintain their own DNS servers and allow their customers to use the
servers to look up addresses.
Page 122 / 180
Reference Manual for the 108 Mbps Wireless Media Router WGT634U
B-10
Network, Routing, Firewall, and Basics
April 2004, 202-10018-02
IP Configuration by DHCP
When an IP-based local area network is installed, each PC must be configured with an IP address.
If the PCs need to access the Internet, they should also be configured with a gateway address and
one or more DNS server addresses. As an alternative to manual configuration, there is a method by
which each PC on the network can automatically obtain this configuration information. A device
on the network may act as a Dynamic Host Configuration Protocol (DHCP) server. The DHCP
server stores a list or pool of IP addresses, along with other information (such as gateway and DNS
addresses) that it may assign to the other devices on the network. The WGT634U Wireless Media
Router has the capacity to act as a DHCP server.
The WGT634U Wireless Media Router also functions as a DHCP client when connecting to the
ISP. The firewall can automatically obtain an IP address, subnet mask, DNS server addresses, and
a gateway address if the ISP provides this information by DHCP.
Internet Security and Firewalls
When your LAN connects to the Internet through a router, an opportunity is created for outsiders
to access or disrupt your network. A NAT router provides some protection because by the very
nature of the process, the network behind the router is shielded from access by outsiders on the
Internet. However, there are methods by which a determined hacker can possibly obtain
information about your network or at the least can disrupt your Internet access. A greater degree of
protection is provided by a firewall router.
What is a Firewall?
A firewall is a device that protects one network from another, while allowing communication
between the two. A firewall incorporates the functions of the NAT router, while adding features for
dealing with a hacker intrusion or attack. Several known types of intrusion or attack can be
recognized when they occur. When an incident is detected, the firewall can log details of the
attempt, and can optionally send email to an administrator notifying them of the incident. Using
information from the log, the administrator can take action with the ISP of the hacker. In some
types of intrusions, the firewall can fend off the hacker by discarding all further packets from the
hacker’s IP address for a period of time.
Page 123 / 180
Reference Manual for the 108 Mbps Wireless Media Router WGT634U
Network, Routing, Firewall, and Basics
B-11
April 2004, 202-10018-02
Stateful Packet Inspection
Unlike simple Internet sharing routers, a firewall uses a process called stateful packet inspection to
ensure secure firewall filtering to protect your network from attacks and intrusions. Since
user-level applications such as FTP and Web browsers can create complex patterns of network
traffic, it is necessary for the firewall to analyze groups of network connection states. Using
Stateful Packet Inspection, an incoming packet is intercepted at the network layer and then
analyzed for state-related information associated with all network connections. A central cache
within the firewall keeps track of the state information associated with all network connections.
All traffic passing through the firewall is analyzed against the state of these connections in order to
determine whether or not it will be allowed to pass through or rejected.
Denial of Service Attack
A hacker may be able to prevent your network from operating or communicating by launching a
Denial of Service (DoS) attack. The method used for such an attack can be as simple as merely
flooding your site with more requests than it can handle. A more sophisticated attack may attempt
to exploit some weakness in the operating system used by your router or gateway. Some operating
systems can be disrupted by simply sending a packet with incorrect length information.
Ethernet Cabling
Most Ethernet networks now use unshielded twisted pair (UTP) cabling. UTP cable has eight
wires arranged in four twisted pairs, and terminated with an RJ45 connector. Normal straight-
through UTP Ethernet cable follows the EIA568B standard as described in
Table B-1
.
Table B-1.
UTP Ethernet cable wiring, straight-through
Pin
Wire color
Signal
1
Orange/White
Transmit (Tx) +
2
Orange
Transmit (Tx) -
3
Green/White
Receive (Rx) +
4
Blue
5
Blue/White
6
Green
Receive (Rx) -
7
Brown/White
8
Brown
Page 124 / 180
Reference Manual for the 108 Mbps Wireless Media Router WGT634U
B-12
Network, Routing, Firewall, and Basics
April 2004, 202-10018-02
Category 5 Cable Quality
Category 5 distributed cable that meets ANSI/EIA/TIA-568-A building wiring standards can be a
maximum of 328 feet (ft.) or 100 meters (m) in length, divided as follows:
20 ft. (6 m) between the hub and the patch panel (if used)
295 ft. (90 m) from the wiring closet to the wall outlet
10 ft. (3 m) from the wall outlet to the desktop device
The patch panel and other connecting hardware must meet the requirements for 100 Mbps
operation (Category 5). Only 0.5 inch (1.5 cm) of untwist in the wire pair is allowed at any
termination point.
A twisted pair Ethernet network operating at 10 Mbits/second (10BASE-T) will often tolerate low
quality cables, but at 100 Mbits/second (10BASE-Tx) the cable must be rated as Category 5, or
Cat 5, by the Electronic Industry Association (EIA). This rating will be printed on the cable jacket.
A Category 5 cable will meet specified requirements regarding loss and crosstalk. In addition,
there are restrictions on maximum cable length for both 10 and 100 Mbits/second networks.
Inside Twisted Pair Cables
For two devices to communicate, the transmitter of each device must be connected to the receiver
of the other device. The crossover function is usually implemented internally as part of the
circuitry in the device. Computers and workstation adapter cards are usually media-dependent
interface ports, called MDI or uplink ports. Most repeaters and switch ports are configured as
media-dependent interfaces with built-in crossover ports, called MDI-X or normal ports.
Auto
Uplink technology automatically senses which connection, MDI or MDI-X, is needed and makes
the right connection.
Figure B-1
illustrates straight-through twisted pair cable.
Page 125 / 180
Reference Manual for the 108 Mbps Wireless Media Router WGT634U
Network, Routing, Firewall, and Basics
B-13
April 2004, 202-10018-02
Figure B-1:
Straight-Through Twisted-Pair Cable
Figure B-2
illustrates crossover twisted pair cable.
Figure B-2:
Crossover Twisted-Pair Cable
Figure B-3:
Category 5 UTP Cable with Male RJ-45 Plug at Each End

Rate

4 / 5 based on 1 vote.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top