1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WGT634U
    5. /
  5. 23
Page 111 / 180 Scroll up to view Page 106 - 110
Technical Specifications
A-1
April 2004, 202-10018-02
Appendix A
Technical Specifications
This appendix provides technical specifications for the 108 Mbps Wireless Media Router
WGT634U.
Network Protocol and Standards Compatibility
Data and Routing Protocols:
TCP/IP, RIP-1, RIP-2, DHCP
PPP over Ethernet (PPPoE)
Power Adapter
North America:
120V, 60 Hz, input
United Kingdom, Australia:
240V, 50 Hz, input
Europe:
230V, 50 Hz, input
Japan:
100V, 50/60 Hz, input
All regions (output):
12 V DC @ 1 A output, 22W maximum
Physical Specifications
Dimensions:
28 x 175 x 118 mm
(1.1 x 6.89 x 4.65 in.)
Weight:
0.3 kg
(0.66 lb)
Environmental Specifications
Operating temperature:
0
°
to 40
°
C
(32º to 104º F)
Operating humidity:
90% maximum relative humidity, noncondensing
Page 112 / 180
Reference Manual for the 108 Mbps Wireless Media Router WGT634U
A-2
Technical Specifications
April 2004, 202-10018-02
Electromagnetic Emissions
Meets requirements of:
FCC Part 15 Class B
VCCI Class B
EN 55 022 (CISPR 22), Class B
Interface Specifications
LAN:
10BASE-T or 100BASE-Tx, RJ-45
WAN:
10BASE-T, RJ-45
Wireless
Radio Data Rates
1, 2, 5.5, 6, 9, 12, 18, 24, 36, 48, 54, and 108 Mbps
Auto Rate Sensing
Frequency
2.4-2.5 GHz
Data Encoding:
Direct Sequence Spread Spectrum (DSSS)
Maximum Computers Per
Wireless Network:
Limited by the amount of wireless network traffic generated
by each node. Typically 30-70 nodes.
Operating Frequency Ranges:
2.412~2.462 GHz (US)
2.457~2.462 GHz (Spain)
2.412~2.484 GHz (Japan)
2.457~2.472 GHz (France)
2.412~2.472 GHz (Europe ETSI)
Encryption:
40-bits (also called 64-bits), 128-bits WEP data encryption
Page 113 / 180
Network, Routing, Firewall, and Basics
B-1
April 2004, 202-10018-02
Appendix B
Network, Routing, Firewall, and Basics
This chapter provides an overview of IP networks, routing, and networking.
Related Publications
As you read this document, you may be directed to various RFC documents for further
information. An RFC is a Request For Comment (RFC) published by the Internet Engineering
Task Force (IETF), an open organization that defines the architecture and operation of the Internet.
The RFC documents outline and define the standard protocols and procedures for the Internet. The
documents are listed on the World Wide Web at
www.ietf.org
and are mirrored and indexed at
many other sites worldwide.
Basic Router Concepts
Large amounts of bandwidth can be provided easily and relatively inexpensively in a local area
network (LAN). However, providing high bandwidth between a local network and the Internet can
be very expensive. Because of this expense, Internet access is usually provided by a slower-speed
wide-area network (WAN) link such as a cable or DSL modem. In order to make the best use of the
slower WAN link, a mechanism must be in place for selecting and transmitting only the data traffic
meant for the Internet. The function of selecting and forwarding this data is performed by a router.
What is a Router?
A router is a device that forwards traffic between networks based on network layer information in
the data and on routing tables maintained by the router. In these routing tables, a router builds up a
logical picture of the overall network by gathering and exchanging information with other routers
in the network. Using this information, the router chooses the best path for forwarding network
traffic.
Routers vary in performance and scale, number of routing protocols supported, and types of
physical WAN connection they support. The 108 Mbps Wireless Media Router WGT634U is a
small office router that routes the IP protocol over a single-user broadband connection.
Page 114 / 180
Reference Manual for the 108 Mbps Wireless Media Router WGT634U
B-2
Network, Routing, Firewall, and Basics
April 2004, 202-10018-02
Routing Information Protocol
One of the protocols used by a router to build and maintain a picture of the network is the Routing
Information Protocol (RIP). Using RIP, routers periodically update one another and check for
changes to add to the routing table.
The WGT634U Wireless Media Router supports both the older RIP-1 and the newer RIP-2
protocols. Among other improvements, RIP-2 supports subnet and multicast protocols. RIP is not
required for most home applications.
IP Addresses and the Internet
Because TCP/IP networks are interconnected across the world, every machine on the Internet must
have a unique address to make sure that transmitted data reaches the correct destination. Blocks of
addresses are assigned to organizations by the Internet Assigned Numbers Authority (IANA).
Individual users and small organizations may obtain their addresses either from the IANA or from
an Internet service provider (ISP). You can contact IANA at www.iana.org.
The Internet Protocol (IP) uses a 32-bit address structure. The address is usually written in dot
notation (also called dotted-decimal notation), in which each group of eight bits is written in
decimal form, separated by decimal points.
For example, the following binary address:
11000011
00100010
00001100
00000111
is normally written as:
195.34.12.7
The latter version is easier to remember and easier to enter into your computer.
In addition, the 32 bits of the address are subdivided into two parts. The first part of the address
identifies the network, and the second part identifies the host node or station on the network. The
dividing point may vary depending on the address range and the application.
There are five standard classes of IP addresses. These address classes have different ways of
determining the network and host sections of the address, allowing for different numbers of hosts
on a network. Each address type begins with a unique bit pattern, which is used by the TCP/IP
software to identify the address class. After the address class has been determined, the software
can correctly identify the host section of the address. The follow figure shows the three main
address classes, including network and host sections of the address for each address type.
Page 115 / 180
Reference Manual for the 108 Mbps Wireless Media Router WGT634U
Network, Routing, Firewall, and Basics
B-3
April 2004, 202-10018-02
Figure 9-1:
Three Main Address Classes
The five address classes are:
•
Class A
Class A addresses can have up to 16,777,214 hosts on a single network. They use an eight-bit
network number and a 24-bit node number. Class A addresses are in this range:
1.x.x.x to 126.x.x.x.
•
Class B
Class B addresses can have up to 65,354 hosts on a network. A Class B address uses a 16-bit
network number and a 16-bit node number. Class B addresses are in this range:
128.1.x.x to 191.254.x.x.
•
Class C
Class C addresses can have 254 hosts on a network. Class C addresses use 24 bits for the
network address and eight bits for the node. They are in this range:
192.0.1.x to 223.255.254.x.
•
Class D
Class D addresses are used for multicasts (messages sent to many hosts). Class D addresses are
in this range:
224.0.0.0 to 239.255.255.255.
•
Class E
Class E addresses are for experimental use.
7261
Class A
Network
Node
Class B
Class C
Network
Node
Network
Node

Rate

4 / 5 based on 1 vote.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top