NETGEAR WGR614v6 Router Manual PDF (Setup & Configuration Guide)

Page 66 / 154 Scroll up to view Page 61 - 65

Reference Manual for the 54 Mbps Wireless Router WGR614 v6

6-14

Advanced Configuration of the Router

202-10099-01, April 2005

2.

Select the Use a dynamic DNS service check box.

3.

Select the name of your dynamic DNS Service Provider.

4.

Type the Host Name (or domain name) that your dynamic DNS service provider gave you.

5.

Type the User Name for your dynamic DNS account.

6.

Type the Password (or key) for your dynamic DNS account.

7.

If your dynamic DNS provider allows the use of wildcards in resolving your URL, you may

select the Use wildcards check box to activate this feature.

For example, the wildcard feature will cause *.yourhost.dyndns.org to be aliased to the same

IP address as yourhost.dyndns.org

8.

Click Apply to save your configuration.

Configuring Static Routes

Static Routes provide additional routing information to your router. Under normal circumstances,

the router has adequate routing information after it has been configured for Internet access, and

you do not need to configure additional static routes. You must configure static routes only for

unusual cases such as multiple routers or multiple IP subnets located on your network.

From the Main Menu of the browser interface, under Advanced, click on Static Routes to view the

Static Route menu, shown below.

Figure 6-9.

Static Route Summary Table

Page 67 / 154

Reference Manual for the 54 Mbps Wireless Router WGR614 v6

Advanced Configuration of the Router

6-15

202-10099-01, April 2005

To add or edit a Static Route:

1.

Click the Add button to open the Add/Edit Menu, shown below.

Figure 6-10.

Static Route Entry and Edit Menu

2.

Type a route name for this static route in the Route Name box under the table.

(This is for identification purposes only.)

3.

Select Private if you want to limit access to the LAN only. The static route will not be reported

in RIP.

4.

Select Active to make this route effective.

5.

Type the Destination IP Address of the final destination.

6.

Type the IP Subnet Mask for this destination.

If the destination is a single host, type 255.255.255.255.

7.

Type the Gateway IP Address, which must be a router on the same LAN segment as the router.

8.

Type a number between 1 and 15 as the Metric value.

This represents the number of routers between your network and the destination. Usually, a

setting of 2 or 3 works, but if this is a direct connection, set it to 1.

9.

Click Apply to have the static route entered into the table.

As an example of when a static route is needed, consider the following case:

•

Your primary Internet access is through a cable modem to an ISP.

•

You have an ISDN router on your home network for connecting to the company where

you are employed. This router’s address on your LAN is 192.168.1.100.

•

Your company’s network is 134.177.0.0.

Page 68 / 154

Reference Manual for the 54 Mbps Wireless Router WGR614 v6

6-16

Advanced Configuration of the Router

202-10099-01, April 2005

When you first configured your router, two implicit static routes were created. A default route was

created with your ISP as the gateway, and a second static route was created to your local network

for all 192.168.1.x addresses. With this configuration, if you attempt to access a device on the

134.177.0.0 network, your router will forward your request to the ISP. The ISP forwards your

request to the company where you are employed, and the request will likely be denied by the

company’s firewall.

In this case you must define a static route, telling your router that 134.177.0.0 should be accessed

through the ISDN router at 192.168.1.100. The static route would look like

Figure 6-10

.

In this example:

•

The Destination IP Address and IP Subnet Mask fields specify that this static route applies to

all 134.177.x.x addresses.

•

The Gateway IP Address fields specifies that all traffic for these addresses should be

forwarded to the ISDN router at 192.168.1.100.

•

A Metric value of 1 will work since the ISDN router is on the LAN.

•

Private is selected only as a precautionary security measure in case RIP is activated.

Enabling Remote Management Access

Using the Remote Management page, you can allow a user or users on the Internet to configure,

upgrade and check the status of your WGR614 v6 router.

Note:

Be sure to change the router's default configuration password to a very secure

password. The ideal password should contain no dictionary words from any language,

and should be a mixture of letters (both upper and lower case), numbers, and symbols.

Your password can be up to 30 characters.

Page 69 / 154

Reference Manual for the 54 Mbps Wireless Router WGR614 v6

Advanced Configuration of the Router

6-17

202-10099-01, April 2005

Figure 6-11:

Remote Management menu

To configure your router for Remote Management:

1.

Select the Turn Remote Management On check box.

2.

Specify what external addresses will be allowed to access the router’s remote management.

Note:

For enhanced security, restrict access to as few external IP addresses as practical.

a.

To allow access from any IP address on the Internet, select Everyone.

b.

To allow access from a range of IP addresses on the Internet, select IP address range.

Enter a beginning and ending IP address to define the allowed range.

c.

To allow access from a single IP address on the Internet, select Only this computer.

Enter the IP address that will be allowed access.

3.

Specify the Port Number that will be used for accessing the management interface.

Web browser access normally uses the standard HTTP service port 80. For greater security,

change the remote management Web interface to a custom port by entering that number in the

box provided. Choose a number between 1024 and 65535, but do not use the number of any

common service port. The default is 8080, which is a common alternate for HTTP.

4.

Click Apply to have your changes take effect.

Page 70 / 154

Reference Manual for the 54 Mbps Wireless Router WGR614 v6

6-18

Advanced Configuration of the Router

202-10099-01, April 2005

Note:

When accessing your router from the Internet, you will type your router's WAN IP address

into your browser's Address (in IE) or Location (in Netscape) box, followed by a colon (:) and the

custom port number. For example, if your external address is 134.177.0.123 and you use port

number 8080, you must enter http://134.177.0.123:8080 in your browser. The Remote

Management Address from the Remote Management Window (see

Figure 6-11

) is the address you

will enter in your browser's address field.

Using Universal Plug and Play (UPnP)

Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers,

access the network and connect to other devices as needed. UPnP devices can

automatically discover the services from other registered UPnP devices on the network.

Figure 6-12.

UPnP Menu

From the Main Menu of the browser interface, under Advanced, click on UPnP. Set up UPnP

according to the guidelines below.

Turn UPnP On:

UPnP can be enabled or disabled for automatic device configuration. The default

setting for UPnP is disabled. If disabled, the router will not allow any device to automatically

control the resources, such as port forwarding (mapping), of the router.

Rate

Popular NETGEAR Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share