1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WGR614v6
    5. /
  5. 10
Page 46 / 154 Scroll up to view Page 41 - 45
Reference Manual for the 54 Mbps Wireless Router WGR614 v6
5-4
Maintenance
202-10099-01, April 2005
Click on the “Show Statistics” button to display router usage statistics, as shown below.
Figure 5-3:
Router Statistics screen
This screen shows the following statistics:
Default Gateway
The WAN (Internet) default gateway the router communicates with.
DHCP Server
The IP address of the DHCP server which provided the IP configuration addresses.
DNS Server
The IP address of the DNS server which provides network name to IP address
translation.
Lease Obtained
When the DHCP lease was obtained.
Lease Expires
When the DHCP lease was expires.
Release
Click the Release button to release the DHCP lease.
Renew
Click the Renew button to renew the DHCP lease.
Table 5-3:
Router Statistics Items
Item
Description
Port
The statistics for the WAN (Internet) and LAN (local) ports. For each port, the screen
displays:
Status
The link status of the port.
TxPkts
The number of packets transmitted on this port since reset or manual clear.
RxPkts
The number of packets received on this port since reset or manual clear.
Collisions
The number of collisions on this port since reset or manual clear.
Tx B/s
The current transmission (outbound) bandwidth used on the WAN and LAN ports.
Table 5-2:
Connection Status Items
(continued)
Item
Description
Page 47 / 154
Reference Manual for the 54 Mbps Wireless Router WGR614 v6
Maintenance
5-5
202-10099-01, April 2005
Viewing a List of Attached Devices
The Attached Devices menu contains a table of all IP devices that the router has discovered on the
local network. From the Main Menu of the browser interface, under the Maintenance heading,
select Attached Devices to view the table, shown below.
Figure 5-4:
Attached Devices menu
For each device, the table shows the IP address, NetBIOS Host Name (if available), and Ethernet
MAC address. Note that if the router is rebooted, the table data is lost until the router rediscovers
the devices. To force the router to look for attached devices, click the Refresh button.
Configuration File Management
The configuration settings of the WGR614 v6 router are stored within the router in a configuration
file. This file can be saved (backed up) to a user’s PC, retrieved (restored) from the user’s PC, or
cleared to factory default settings.
Rx B/s
The current reception (inbound) bandwidth used on the WAN and LAN ports.
Up Time
The amount of time since the router was last restarted.
Up Time
The time elapsed since this port acquired the link.
Poll Interval
Specifies the intervals at which the statistics are updated in this window. Click on Stop
to freeze the display.
Set Interval
Enter a time and click the button to set the polling frequency.
Stop
Click the Stop button to freeze the polling information.
Table 5-3:
Router Statistics Items
(continued)
Item
Description
Page 48 / 154
Reference Manual for the 54 Mbps Wireless Router WGR614 v6
5-6
Maintenance
202-10099-01, April 2005
From the Main Menu of the browser interface, under the Maintenance heading, select the Settings
Backup heading to bring up the menu shown below.
Figure 5-5:
Settings Backup menu
Three options are available, and are described in the following sections.
Restoring and Backing Up the Configuration
The Restore and Backup options in the Settings Backup menu allow you to save and retrieve a file
containing your router’s configuration settings.
To save your settings, click the Backup button. Your browser will extract the configuration file
from the router and will prompt you for a location on your PC to store the file. You can give the
file a meaningful name at this time, such as pacbell.cfg.
To restore your settings from a saved configuration file, enter the full path to the file on your PC or
click the Browse button to browse to the file. When you have located it, click the Restore button to
send the file to the router. The router will then reboot automatically.
Warning
: Do not interrupt the reboot process.
Page 49 / 154
Reference Manual for the 54 Mbps Wireless Router WGR614 v6
Maintenance
5-7
202-10099-01, April 2005
Erasing the Configuration
It is sometimes desirable to restore the router to original default settings. This can be done by using
the Erase function, which will restore all factory settings. After an erase, the router's password will
be
password
, the LAN IP address will be 192.168.1.1, and the router's DHCP client will be
enabled.
To erase the configuration, click the Erase button.
To restore the factory default configuration settings without knowing the login password or IP
address, you must use the Default Reset button on the rear panel of the router. See
“Restoring the
Default Configuration and Password” on page 7-7
.
Upgrading the Router Software
The routing software of the WGR614 v6 router is stored in FLASH memory, and can be upgraded
as new software is released by NETGEAR. Upgrade files can be downloaded from the NETGEAR
Web site. If the upgrade file is compressed (.ZIP file), you must first extract the file before sending
it to the router. The upgrade file can be sent to the router using your browser.
Note:
The Web browser used to upload new firmware into the WGR614 v6 router must support
HTTP uploads. NETGEAR recommends using Microsoft Internet Explorer 5.0 and above and
Netscape Navigator 4.7 and above.
From the Main Menu of the browser interface, under the Maintenance heading, select the Router
Upgrade link display the menu shown below.
Note:
Before upgrading the router software, use the router backup utility to save your
configuration settings. Any router upgrade will revert the router settings back to the
factory defaults. After completing the upgrade, you can restore your settings from the
backup.
Page 50 / 154
Reference Manual for the 54 Mbps Wireless Router WGR614 v6
5-8
Maintenance
202-10099-01, April 2005
Figure 5-6:
Router Upgrade menu
To upload new firmware:
1.
Download and unzip (if the downloaded file is a .zip file) the new software file from
NETGEAR.
2.
In the Router Upgrade menu, click the Browse button and browse to the location of the
upgrade file
3.
Click Upload.
Note:
When uploading software to the WGR614 v6 router, it is important not to interrupt the
Web browser by closing the window, clicking a link, or loading a new page. If the browser is
interrupted, it may corrupt the software. When the upload is complete, your router will
automatically restart. The upgrade process will typically take about one minute.
In some cases, you may need to reconfigure the router after upgrading.
Changing the Administrator Password
The default password for the router’s Web Configuration Manager is
password
. NETGEAR
recommends that you change this password to a more secure password.
Note:
Before changing the router password, use the router backup utility to save your
configuration settings. If after changing the password, you forget the new password you
assigned, you will have to reset the router back to the factory defaults to be able to log in
using the default password of password. This means you will have to restore all the
router configuration settings. If you ever have to reset the router back to the factory
defaults, you can restore your settings from the backup.

Rate

3.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top