1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WGPS606
    5. /
  5. 3
Page 11 / 66 Scroll up to view Page 6 - 10
Introduction
2-1
202-10083-01
Chapter 2
Introduction
This chapter introduces the NETGEAR NETGEAR 54 Mbps Wireless USB Print Server with
4-Port Switch WGPS606. Minimal prerequisites for installation are presented in
“System
Requirements” on page 2-3
.
About the Wireless USB Print Server
This manual describes the installation and use of the WGPS606 for operation with a Microsoft®
Windows® XP, Windows® 2000, Windows® Me, or Windows® 98SE system.
For quick installation and setup, please see the WGPS606 54 Mbps Wireless USB Print Server
Installation Guide. This manual describes in detail how to set up the WGPS606 and provides you
with further reference information.
Any wired or wirelessly connected device in your network can print using printers connected to
your wireless USB print server. The WGPS606 provides connectivity to multiple network devices
interacting with the built-in switch and with a wireless router or access point. Typically, an
in-doors access point provides a maximum connectivity area with about a 300 foot radius. Your
wireless USB print server provides direct wired connectivity for up to 4 computers and up to 2
USB printers as well as wireless connectivity for other devices in the network.
The auto-sensing capability of the NETGEAR 54 Mbps Wireless USB Print Server with 4-Port
Switch WGPS606 allows packet transmission at up to 54 Mbps, or at reduced speeds to
compensate for distance or electromagnetic noise interference.
Support for Standards
The following standards and conventions are supported:
•
Standards Compliant
.
The Wireless USB Print Server complies with the IEEE 802.11g
(DSSS).
•
WEP support.
Support for WEP is included. Both 64-bit and 128-bit keys are supported.
•
WPA-PSK support
. Support for Wi-Fi Protected Access (WPA) data encryption which
provides strong data encryption and authentication based on a pre-shared key.
Page 12 / 66
Reference Manual for the NETGEAR 54 Mbps Wireless USB Print Server with 4-Port Switch
2-2
Introduction
202-10083-01
•
DHCP Support.
—
Client:
The WGPS606 can act as a client and obtain information from your DHCP server.
—
Pass Through
: For devices connected to its switch, the WGPS606 will pass through
exchanges to your DHCP server.
Key Features
The WGPS606 provides solid functionality, including these features:
•
Easy Configuration.
The NETGEAR Smart Wizard software that assures fast and easy setup
for Windows 98SE, Windows Me, Windows 2000, and Windows XP
•
Upgradeable Firmware.
Firmware is stored in a flash memory and can be upgraded easily,
using only your Web browser, and can be upgraded remotely.
•
Autosensing Ethernet Connection with
Auto Uplink
I
nterface.
Connects to 10/100 Mbps
IEEE 802.3 Ethernet networks.
•
LED Indicators.
Power and wireless activity are easily identified.
802.11g Standards-based Wireless Networking
The NETGEAR 54 Mbps Wireless USB Print Server with 4-Port Switch WGPS606 provides a
bridge between Ethernet wired LANs and 802.11g compatible wireless LAN networks. It provides
connectivity between Ethernet wired networks and wireless router or access point systems.
Additionally, the WGPS606 supports the following wireless features:
•
Distributed coordinated function (CSMA/CA, Back off procedure, ACK procedure,
retransmission of unacknowledged frames)
•
RTS/CTS handshake
•
Packet fragmentation and reassembly
•
Authentication Algorithms (Open System, WEP Shared Key, WPA-PSK)
•
Short or long preamble
Page 13 / 66
Reference Manual for the NETGEAR 54 Mbps Wireless USB Print Server with 4-Port Switch
Introduction
2-3
202-10083-01
Autosensing Ethernet Connections with Auto Uplink
The WGPS606 can connect to a standard Ethernet network. The LAN interface is autosensing and
capable of full-duplex or half-duplex operation. The wireless USB print server incorporates Auto
Uplink
TM
technology. The Ethernet port will automatically sense whether the Ethernet cable
plugged into the port should have a ‘normal’ connection such as to a PC or an ‘uplink’ connection
such as to a switch or hub. That port will then configure itself to the correct configuration. This
feature also eliminates any concerns about crossover cables, as Auto Uplink will accommodate
either type of cable to make the right connection.
System Requirements
Before installing the WGPS606, make sure your network meets these requirements:
•
A 100-240 V, 50-60 HZ AC power source
•
A Web browser for configuration such as Microsoft Internet Explorer 5.0 or above, or
Netscape Navigator 4.78 or above
•
At least one Pentium class computer (or equivalent) with the TCP/IP protocol installed and a
CD-ROM drive
•
An 802.11b or 802.11g-compliant router or access point
Page 14 / 66
Reference Manual for the NETGEAR 54 Mbps Wireless USB Print Server with 4-Port Switch
2-4
Introduction
202-10083-01
What’s In the Box?
The product package should contain the following items:
•
NETGEAR 54 Mbps Wireless USB Print Server with 4-Port Switch WGPS606
•
Power adapter and cord (12Vdc, 1A)
•
Printed WGPS606 54 Mbps Wireless USB Print Server Installation Guide
•
Resource CD for the NETGEAR 54 Mbps Wireless Access Point
–
Setup Wizards
–
Reference Manual for the NETGEAR 54 Mbps Wireless USB Print Server with 4-Port
Switch WGPS606 (202-10083-01)—this manual
–
Soft copy of the WGPS606 54 Mbps Wireless USB Print Server Installation Guide
•
Support Information card
•
Warranty and Registration card
Contact your reseller or customer support in your area if there are any wrong, missing, or damaged
parts. You can refer to the Support Information Card for the telephone number of customer support
in your area. You should keep the Support Information card, along with the original packing
materials, and use the packing materials to repack the WGPS606 if you need to return it for repair.
To qualify for product updates and product warranty registrations, we encourage you to register on
the NETGEAR Web site at:
.
Bottom Label Description
The NETGEAR 54 Mbps Wireless USB Print Server with 4-Port Switch WGPS606 front and rear
hardware functions are described on the bottom label illustrated below.
Page 15 / 66
Reference Manual for the NETGEAR 54 Mbps Wireless USB Print Server with 4-Port Switch
Introduction
2-5
202-10083-01
Figure 2-1: WGPS606 bottom label
The following table describes the bottom label information:
ITEM
DESCRIPTION
Power Status Light
Off
On Green
Yellow Blink
Yellow Solid
Power Indicator
No power.
Power is on and it has completed its power on self test diagnostic.
Power is on and it is performing its power on self test diagnostic.
Power is on and it has failed its power on self test diagnostic.
Printer LPT1 & LPT2
Status Lights
Print Activity Indicators
Off
Printer detached or turned off.
Green On
Printer ready.
Green Blink
Print activity.
Yellow 0n
Print error.
Wireless Status Light
Wireless LAN Link Activity Indicator
Blue, Off/On
Off wireless feature turned off/On Blue wireless link enabled, no activity.
Off, Blue Alternating Blink
Seeking wireless connection.
Blue Fast Blink
Wireless link activity.
°?ajË¡¢Ë*£¡¢?
,jÄ¡~¢jaËMßË!-05-".Ë¡¢Ë*?¤¡w¥Á¢¡?
3893
143<7:
4**Ë7,]Ë+:Ï85+/ÉåÉ
ÔÈÔ¦§åÔåå¦å§
°"*
/-.7">
ÖÄjÁË¢?¨j]ËË?a¨¡¢
¬?ÄÄÝ¥Áa]Ëˬ?ÄÄÝ¥Áa
,-4"2>0Ë"**-//
+¥ÝjÁ
>+0
§
>+0
Ô
8¡Áj¤jÄÄ
)>7!=ËsË"*07970:
>"!]Ë5.--!Ës§ååË°M¬ÄËÊË:->>#8Ës§åË°M¬Ä
§Ô9,*^˧±å"
.jÄÍ¥Áj
4?WÍ¥ÁßË
/jÍÍ¡¢~Ä
>+0
§
>+0
Ô
>"!
§
>"!
Ô
>"!
Ï
>"!
|
y|°M¬ÄË8¡Áj¤jÄÄË+Á¡¢ÍË/jÁÜjÁËÝ¡Í£Ë|¦¬¥ÁÍË/Ý¡ÍW£Ë
85+.ÉåÉ

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top