1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. VEGN2610-1FXAUS FOXTEL
    5. /
  5. 5
Page 21 / 123 Scroll up to view Page 16 - 20
Internet Setup
21
Dual Band Wireless VDSL2 + Ethernet Gateway
Otherwise, the default settings are adequate.
6.
In the
Multiplexing Method
list, select
LLC-based
or
VC-based
.
7.
In the
VPI
field, type a number from 0 through 255.
The default is 8.
8.
In the
VCI
field, type a number from 32 through 65535.
The default is 35.
9.
Click the
Apply
button.
Your settings are saved.
Specify IPv6 Internet Connections
You can set up an IPv6 Internet connection if genie does not detect it automatically.
To set up an IPv6 Internet connection:
1.
Launch an Internet browser from a computer or wireless device that is connected to the
network.
2.
Type
or
.
A login screen displays.
3.
Enter the gateway user name and password.
The user name is
admin
. The default password is
password
. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4.
Select
Advanced > Advanced Setup > IPv6
.
The Basic Settings screen displays.
5.
In the
Internet Connection Type
list, select the IPv6 connection type:
•
If your ISP did not provide details, select
IPv6 Tunnel
.
•
If you are not sure, select
Auto Detect
so that the gateway detects the IPv6 type that
is in use.
•
If your Internet connection does not use PPPoe or DHCP, or not fixed, but is IPv6,
select
Auto Config
.
Your Internet service provider (ISP) can provide this information.
6.
Click the
Apply
button.
Your changes take effect.
Page 22 / 123
Internet Setup
22
Dual Band Wireless VDSL2 + Ethernet Gateway
Requirements for Entering IPv6 Addresses
IPv6 addresses are denoted by eight groups of hexadecimal quartets that are separated by
colons. You can reduce any four-digit group of zeros within an IPv6 address to a single zero
or omit it. The following errors invalidate an IPv6 address:
•
More than eight groups of hexadecimal quartets
•
More than four hexadecimal characters in a quartet
•
More than two colons in a row
Use Auto Detect for an IPv6 Internet Connection
To set up an IPv6 Internet connection through auto detection:
1.
Launch an Internet browser from a computer or wireless device that is connected to the
network.
2.
Type
or
.
A login screen displays.
3.
Enter the gateway user name and password.
The user name is
admin
. The default password is
password
. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4.
Select
Advanced > Advanced Setup > IPv6
.
The IPv6 screen displays.
5.
In the
Internet Connection Type
list, select
Auto Detect
.
6.
Click the
Apply
button.
The screen adjusts.
The gateway automatically detects the information in the following fields:
•
Connection Type
. This field indicates the connection type that is detected.
•
Router’s IPv6 Address on WAN
. This field shows the IPv6 address that is acquired
for the gateway’s WAN (or Internet) interface. The number after the slash (/) is the
length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
•
Router’s IPv6 Address on LAN
. This field shows the IPv6 address that is acquired
for the gateway’s LAN interface. The number after the slash (/) is the length of the
prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
7.
Select an IP Address Assignment radio button.
•
Use DHCP Server
. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
Page 23 / 123
Internet Setup
23
Dual Band Wireless VDSL2 + Ethernet Gateway
•
Auto Config
. This is the default setting.
This setting specifies how the gateway assigns IPv6 addresses to the devices on your
home network (the LAN).
8.
(Optional) Select the
Use This Interface ID
check box and specify the interface ID to be
used for the IPv6 address of the gateway’s LAN interface.
If you do not specify an ID here, the gateway generates one automatically from its MAC
address.
9.
Click the
Apply
button.
Your settings are saved.
Use Auto Config for an IPv6 Internet Connection
To set up an IPv6 Internet connection through auto configuration:
1.
Launch an Internet browser from a computer or wireless device that is connected to the
network.
2.
Type
or
.
A login screen displays.
3.
Enter the gateway user name and password.
The user name is
admin
. The default password is
password
. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4.
Select
Advanced > Advanced Setup > IPv6
.
The IPv6 screen displays.
5.
In the
Internet Connection Type
list, select
Auto Config
.
The screen adjusts:
The gateway automatically detects the information in the following fields:
Page 24 / 123
Internet Setup
24
Dual Band Wireless VDSL2 + Ethernet Gateway
•
Router’s IPv6 Address on WAN
. This field shows the IPv6 address that is acquired
for the gateway’s WAN (or Internet) interface. The number after the slash (/) is the
length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
•
Router’s IPv6 Address on LAN
. This field shows the IPv6 address that is acquired
for the gateway’s LAN interface. The number after the slash (/) is the length of the
prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
6.
(Optional) In the
DHCP User Class (If Required)
field, enter a host name.
Most people can leave this field blank, but if your ISP has given you a specific host name,
enter it here.
7.
(Optional) In the
DHCP Domain Name (If Required)
field, enter a domain name.
You can type the domain name of your IPv6 ISP. Do not enter the domain name for the
IPv4 ISP here. For example, if your ISP’s mail server is mail.xxx.yyy.zzz, type xxx.yyy.zzz
as the domain name. If your ISP provided a domain name, type it in this field. For
example, Earthlink Cable might require a host name of home, and Comcast sometimes
supplies a domain name.
8.
Select an IP Address Assignment radio button.
•
Use DHCP Server
. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config
. This is the default setting.
This setting specifies how the gateway assigns IPv6 addresses to the devices on your
home network (the LAN).
9.
(Optional) Select the
Use This Interface ID
check box and specify the interface ID that you
want to be used for the IPv6 address of the gateway’s LAN interface.
If you do not specify an ID here, the gateway generates one automatically from its MAC
address.
10.
Click the
Apply
button.
Your settings are saved.
Set Up an IPv6 6to4 Tunnel Internet Connection
The remote relay gateway is the gateway to which your gateway creates a 6to4 tunnel. Make
sure that the IPv4 Internet connection is working before you apply the 6to4 tunnel settings for
the IPv6 connection.
To set up an IPv6 Internet connection by using a 6to4 tunnel:
1.
Launch an Internet browser from a computer or wireless device that is connected to the
network.
2.
Type
or
.
A login screen displays.
Page 25 / 123
Internet Setup
25
Dual Band Wireless VDSL2 + Ethernet Gateway
3.
Enter the gateway user name and password.
The user name is
admin
. The default password is
password
. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4.
Select
Advanced > Advanced Setup > IPv6
.
The IPv6 screen displays.
5.
In the
Internet Connection Type
list, select
6to4 Tunnel
.
The screen adjusts:
The gateway automatically detects the information in the Router’s IPv6 Address on LAN
field. This field shows the IPv6 address that is acquired for the gateway’s LAN interface.
The number after the slash (/) is the length of the prefix, which is also indicated by the
underline (_) under the IPv6 address. If no address is acquired, the field displays Not
Available.
6.
Select a Remote 6to4 Relay Router radio button:
•
Auto
. Your gateway uses any remote relay gateway that is available on the Internet.
This is the default setting.
•
Static IP Address
. Enter the static IPv4 address of the remote relay gateway. Your
IPv6 ISP usually provides this address.
7.
Select an IP Address Assignment radio button.
•
Use DHCP Server
. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config
. This is the default setting.
This setting specifies how the gateway assigns IPv6 addresses to the devices on your
home network (the LAN).
8.
(Optional) Select the
Use This Interface ID
check box and specify the interface ID that you
want to be used for the IPv6 address of the gateway’s LAN interface.
If you do not specify an ID here, the gateway generates one automatically from its MAC
address.

Rate

4 / 5 based on 1 vote.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top