1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. R6200v2
    5. /
  5. 25
Page 121 / 131 Scroll up to view Page 116 - 120
Troubleshooting
121
R6200v2 Smart WiFi Router
•
Your ISP allows only one Ethernet MAC address to connect to Internet and might check
for your computer’s MAC address. In this case, do one of the following:
-
Inform your ISP that you have bought a new network device, and ask them to use the
router’s MAC address.
-
Configure your router to clone your computer’s MAC address.
If your router can obtain an IP address, but your computer is unable to load any web pages
from the Internet:
•
Your computer might not recognize any DNS server addresses.
A DNS server is a host on the Internet that translates Internet names (such as www
addresses) to numeric IP addresses. Typically, your ISP provides the addresses of one or
two DNS servers for your use. If you entered a DNS address during the router’s
configuration, reboot your computer, and verify the DNS address. You can configure your
computer manually with DNS addresses, as explained in your operating system
documentation
.
•
Your computer might not have the router configured as its TCP/IP gateway.
If your computer obtains its information from the router by DHCP, reboot the computer,
and verify the gateway address.
•
You might be running login software that is no longer needed.
If your ISP provided a program to log you in to the Internet (such as WinPoET), you no
longer need to run that software after installing your router. You might need to go to
Internet Explorer and select
Tools > Internet Options
, click the
Connections
tab, and
select
Never dial a connection
.
Troubleshoot PPPoE
If you are using PPPoE, try troubleshooting your Internet connection.
To troubleshoot a PPPoE connection:
1.
Select
Administration > Router Status
.
2.
Click
Connection Status
.
3.
Check the Connection Status display to see if your PPPoE connection is up and working.
4.
If any of the fields on the Connection Status screen indicate Failed, you can attempt to
reconnect by clicking
Connect
. The router continues to attempt to connect indefinitely.
5.
If you cannot connect after several minutes, you might be using an incorrect service name,
user name, or password. There might also be a provisioning problem with your ISP.
Note:
Unless you connect manually, the router does not authenticate using
PPPoE until data is transmitted to the network.
Page 122 / 131
Troubleshooting
122
R6200v2 Smart WiFi Router
Troubleshoot Internet Browsing
If your router can obtain an IP address but your computer is unable to load any web pages
from the Internet, check the following:
•
Your computer might not recognize any DNS server addresses. A DNS server is a host
on the Internet that translates Internet names (such as www addresses) to numeric IP
addresses.
Typically, your ISP provides the addresses of one or two DNS servers for your use. If you
entered a DNS address during the router’s configuration, restart your computer.
Alternatively, you can configure your computer manually with a DNS address, as
explained in the documentation for your computer.
•
Your computer might not have the router configured as its default gateway.
Reboot the computer and verify that the router address (www.routerlogin.net) is listed by
your computer as the default gateway address.
•
You might be running login software that is no longer needed. If your ISP provided a
program to log you in to the Internet (such as WinPoET), you no longer need to run that
software after installing your router. You might need to go to Internet Explorer and select
Tools > Internet Options
, click the
Connections
tab, and select
Never dial a
connection
.
Changes Not Saved
If the router does not save the changes you make in the router interface, check the following:
•
When entering configuration settings, always click the
Apply
button before moving to
another screen or tab, or your changes are lost.
•
Click the
Refresh
or
Reload
button in the web browser. The changes might have
occurred, but the old settings might be in the web browser’s cache.
Wireless Connectivity
If you are having trouble connecting wirelessly to the router, try to isolate the problem.
•
Does the wireless device or computer that you are using find your wireless network?
If not, check the WiFi LED on the front of the router. If it is off, you can press the
WiFi
On/Off
button on the side of the router to turn the router wireless radios back on.
If you disabled the router’s SSID broadcast, then your wireless network is hidden and
does not show up in your wireless client’s scanning list. (By default, SSID broadcast is
enabled.)
•
Does your wireless device support the security that you are using for your wireless
network (WPA or WPA2)?
Page 123 / 131
Troubleshooting
123
R6200v2 Smart WiFi Router
•
If you want to view the wireless settings for the router, use an Ethernet cable to connect a
computer to a LAN port on the router. Then log in to the router, and select
Wireless
see
(
Basic Wireless Settings
on page
25).
Note:
Be sure to click the
Apply
button if you changed the settings.
If your wireless device finds your network, but the signal strength is weak, check these
conditions:
•
Is your router too far from your computer, or too close? Place your computer near the
router, but at least 6 feet (1.8 meters) away, and see whether the signal strength
improves.
•
Are objects between the router and your computer blocking the wireless signal?
Troubleshoot Your Network Using the Ping Utility
Most network devices and routers contain a ping utility that sends an echo request packet to
the designated device. The device then responds with an echo reply. You can easily
troubleshoot a network is easy using the ping utility in your computer or workstation.
Test the LAN Path to Your Router
You can ping the router from your computer to verify that the LAN path to your router is set up
correctly.
To ping the router from a Windows computer:
1.
From the Windows toolbar, click
Start
and select
Run
.
2.
In the field provided, type
ping
followed by the IP address of the router, as in this example:
ping www.routerlogin.net
3.
Click
OK
.
You should see a message like this one:
Pinging <IP address > with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
Request timed out
If the path is not functioning correctly, you could have one of the following problems:
•
Wrong physical connections
For a wired connection, make sure that the numbered LAN port LED is lit for the port to
which you are connected.
Page 124 / 131
Troubleshooting
124
R6200v2 Smart WiFi Router
Check that the appropriate LEDs are on for your network devices. If your router and
computer are connected to a separate Ethernet switch, make sure that the link LEDs are
lit for the switch ports that are connected to your computer and router.
•
Wrong network configuration
Verify that the Ethernet card driver software and TCP/IP software are both installed and
configured on your computer.
Verify that the IP address for your router and your computer are correct and that the
addresses are on the same subnet.
Test the Path from Your Computer to a Remote Device
After verifying that the LAN path works correctly, test the path from your computer to a remote
device.
1.
From the Windows toolbar, click the
Start
button and select
Run
.
2.
In the Windows Run window, type:
ping -n 10
<
IP address
>
where <IP address> is the IP address of a remote device such as your ISP DNS server.
If the path is functioning correctly, replies like those shown in the previous section are
displayed.
If you do not receive replies:
•
Check that your computer has the IP address of your router listed as the default gateway.
If the IP configuration of your computer is assigned by DHCP, this information is not
visible in your computer Network Control Panel. Verify that the IP address of the router is
listed as the default gateway.
•
Check to see that the network address of your computer (the portion of the IP address
specified by the subnet mask) is different from the network address of the remote device.
•
Check that your cable or DSL modem is connected and functioning.
•
If your ISP assigned a host name to your computer, enter that host name as the account
name in the Internet Setup screen.
•
Your ISP could be rejecting the Ethernet MAC addresses of all but one of your computers.
Many broadband ISPs restrict access by allowing traffic only from the MAC address of your
broadband modem. Some ISPs additionally restrict access to the MAC address of a single
computer connected to that modem. If so, configure your router to “clone” or “spoof” the MAC
address from the authorized computer.
Page 125 / 131
125
A
A.
Supplemental Information
This appendix covers the following topics:
•
Factory Settings
•
Technical Specifications

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top