Page 36 / 130 Scroll up to view Page 31 - 35
Genie Advanced Home
36
Dual Band 11ac WiFi Router R6200
2.
Click
Next
. The following screen lets you select the method for adding the WPS client (a
wireless device or computer).
You can use either the push button or PIN method.
3.
Select either
Push Button
or
PIN Number
.
To use the push-button method, either click the
WPS
button on this screen, or press
the
WPS
button on the side of the router. Within 2 minutes, go to the wireless client
and press its
WPS
button to join the network without entering a password.
To use the PIN method, select the
PIN Number
radio button, enter the client security
PIN, and click
Next
.
Within 2 minutes, go to the client device and use its WPS software to join the network
without entering a password.
The router attempts to add the WPS-capable device. The WPS LED
on the front of
the router blinks green. When the router establishes a WPS connection, the LED is solid
green, and the router WPS screen displays a confirmation message.
4.
Repeat Step 2 and Step 3 to add another WPS client to your network.
Page 37 / 130
Genie Advanced Home
37
Dual Band 11ac WiFi Router R6200
Setup Menu
To display the Setup menu:
Select
Advanced > Setup
to display the Setup menu.
The following selections are available:
Internet Setup
. Go to the same Internet Setup screen that you can access from the
dashboard on the Basic Home screen. See
Internet Setup
on page
22.
Wireless Setup
. Go to the same Wireless Settings screen that you can access from
the dashboard on the Basic Home screen. See
Basic Wireless Settings
on page
28.
Guest Network
. This is a shortcut to the same Guest Network screen that you can
access from the dashboard on the Basic Home screen. See
Guest Networks
on
page
31.
WAN Setup
. Internet (WAN) setup. See
WAN Setup
on page
37.
LAN Setup
. Local area network (LAN) setup. See
LAN Setup
on page
40.
QoS Setup
. Quality of Service (QoS) setup. See
Quality of Service (QoS) Setup
on
page
43.
WAN Setup
The WAN Setup screen lets you configure a DMZ (demilitarized zone) server, change the
Maximum Transmit Unit (MTU) size, and enable the router to respond to a ping on the WAN
(Internet) port.
To view or change the WAN settings:
Select
Advanced > Setup > WAN Setup
:
The following settings are available:
Page 38 / 130
Genie Advanced Home
38
Dual Band 11ac WiFi Router R6200
Disable Port Scan and DoS Protection
. DoS protection protects your LAN against
denial of service attacks such as Syn flood, Smurf Attack, Ping of Death, Teardrop
Attack, UDP Flood, ARP Attack, Spoofing ICMP, Null Scan, and many others. This
should be disabled only in special circumstances.
Default DMZ Server
. This feature is sometimes helpful when you are playing online
games or videoconferencing. Be careful when using this feature because it makes the
firewall security less effective. See the following section,
Default DMZ Server
, for
more details.
Respond to Ping on Internet Port
. If you want the router to respond to a ping from
the Internet, select this check box. Use this setting only as a diagnostic tool because it
allows your router to be discovered. Do not select this check box unless you have a
specific reason.
Disable IGMP Proxying
. IGMP proxying allows a computer on the local area network
(LAN) to receive the multicast traffic it is interested in from the Internet. If you do not
need this feature, you can select this check box to disable it.
MTU Size (in bytes)
. The normal MTU (Maximum Transmit Unit) value for most
Ethernet networks is 1500 bytes, or 1492 bytes for PPPoE connections. For some
ISPs, you might need to reduce the MTU. This is rarely required. Only reduce the
MTU if you are sure that it is necessary for your ISP connection. See
Change the
MTU Size
on page
39.
NAT Filtering
. Network Address Translation (NAT) determines how the router
processes inbound traffic. Secured NAT provides a secured firewall to protect the
computers on the LAN from attacks from the Internet, but might prevent some Internet
games, point-to-point applications, or multimedia applications from functioning. Open
NAT provides a much less secured firewall, but allows almost all Internet applications
to function.
Default DMZ Server
The default DMZ server feature is helpful when you are using some online games and
videoconferencing applications that are incompatible with Network Address Translation
(NAT). The router is programmed to recognize some of these applications and to work
correctly with them, but there are other applications that might not function well. In some
cases, one local computer can run the application correctly if the IP address for that computer
is entered as the default DMZ server.
WARNING:
DMZ servers pose a security risk. A computer designated as the
default DMZ server loses much of the protection of the firewall and
is exposed to exploits from the Internet. If compromised, the DMZ
server computer can be used to attack other computers on your
network.
Page 39 / 130
Genie Advanced Home
39
Dual Band 11ac WiFi Router R6200
The router usually detects and discards Incoming traffic from the Internet that is not a
response to one of your local computers or a service that you have configured in the Port
Forwarding/Port Triggering screen. Instead of discarding this traffic, you can have the router
forward the traffic to one computer on your network. This computer is called the default DMZ
server.
To set up a default DMZ server:
1.
On the WAN Setup screen, select the
Default DMZ Server
check box.
2.
Type the IP address.
3.
Click
Apply
.
Change the MTU Size
The maximum transmission unit (MTU) is the largest data packet a network device transmits.
When one network device communicates across the Internet with another, the data packets
travel through many devices along the way. If a device in the data path has a lower MTU
setting than the other devices, the data packets have to be split or “fragmented” to
accommodate the device with the smallest MTU.
The best MTU setting for NETGEAR equipment is often just the default value. In some
situations, changing the value fixes one problem but causes another. Leave the MTU
unchanged unless one of these situations occurs:
You have problems connecting to your ISP or other Internet service, and the technical
support of either the ISP or NETGEAR recommends changing the MTU setting. These
web-based applications might require an MTU change:
-
A secure website that does not open, or displays only part of a web page
-
Yahoo email
-
MSN portal
-
America Online’s DSL service
You use VPN and have severe performance problems.
You used a program to optimize MTU for performance reasons, and now you have
connectivity or performance problems.
Note:
An incorrect MTU setting can cause Internet communication
problems. For instance, you might not be able to access certain
websites, frames within websites, secure login pages, or FTP or
POP servers.
If you suspect an MTU problem, a common solution is to change the MTU to 1400. If you are
willing to experiment, you can gradually reduce the MTU from the maximum value of 1500
Page 40 / 130
Genie Advanced Home
40
Dual Band 11ac WiFi Router R6200
until the problem goes away. The following table describes common MTU sizes and
applications.
Table 2.
Common MTU Sizes
MTU
Application
1500
The largest Ethernet packet size and the default value. This setting is typical for
connections that do not use PPPoE or VPN, and is the default value for NETGEAR
routers, adapters, and switches.
1492
Used in PPPoE environments.
1472
Maximum size to use for pinging. (Larger packets are fragmented.)
1468
Used in some DHCP environments.
1460
Usable by AOL if you do not have large email attachments, for example.
1436
Used in PPTP environments or with VPN.
1400
Maximum size for AOL DSL.
576
Typical value to connect to dial-up ISPs.
To change the MTU size:
1.
Select
Advanced > Setup > WAN Setup
.
2.
In the MTU Size field, enter a value from 64 to 1500.
3.
Click
Apply
to save the settings.
LAN Setup
The LAN Setup screen allows configuration of LAN IP services such as Dynamic Host
Configuration Protocol (DHCP) and Routing Information Protocol (RIP).
The router is shipped preconfigured to use private IP addresses on the LAN side and to act
as a DHCP server. The router’s default LAN IP configuration is:
LAN IP address.
192.168.1.1
Subnet mask.
255.255.255.0
These addresses are part of the designated private address range for use in private networks
and are suitable for most applications. If your network requires a different IP addressing
scheme, you can change these settings in the LAN Setup screen.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top