1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. FWG114P
    5. /
  5. 44
Page 216 / 296 Scroll up to view Page 211 - 215
Reference Manual for the ProSafe Wireless 802.11g
Firewall/Print Server Model FWG114P v2
C-6
Preparing Your Network
201-10301-02, May 2005
5.
Verify that ‘Client for Microsoft Networks’ and ‘Internet Protocol (TCP/IP)’ are present. If
not, select Install and add them.
6.
Select ‘Internet Protocol (TCP/IP)’, click Properties, and verify that “Obtain an IP address
automatically is selected.
7.
Click OK and close all Network and Dialup Connections windows.
8.
Make sure your PC is connected to the firewall, then reboot your PC.
Verifying TCP/IP Properties
To check your PC’s TCP/IP configuration:
1.
On the Windows taskbar, click the Start button, and then click Run.
The Run window opens.
2.
Type
cmd
and then click OK.
A command window opens
3.
Type
ipconfig /all
Your IP Configuration information will be listed, and should match the values below if you are
using the default TCP/IP settings that NETGEAR recommends:
•
The IP address is between 192.168.0.2 and 192.168.0.254
•
The subnet mask is 255.255.255.0
•
The default gateway is 192.168.0.1
4.
Type
exit
Configuring the Macintosh for TCP/IP Networking
Beginning with Macintosh Operating System 7, TCP/IP is already installed on the Macintosh. On
each networked Macintosh, you will need to configure TCP/IP to use DHCP.
MacOS 8.6 or 9.x
1.
From the Apple menu, select Control Panels, then TCP/IP.
Page 217 / 296
Reference Manual for the ProSafe Wireless 802.11g
Firewall/Print Server Model FWG114P v2
Preparing Your Network
C-7
201-10301-02, May 2005
The TCP/IP Control Panel opens:
2.
From the “Connect via” box, select your Macintosh’s Ethernet interface.
3.
From the “Configure” box, select Using DHCP Server.
You can leave the DHCP Client ID box empty.
4.
Close the TCP/IP Control Panel.
5.
Repeat this for each Macintosh on your network.
MacOS X
1.
From the Apple menu, choose System Preferences, then Network.
2.
If not already selected, select Built-in Ethernet in the Configure list.
3.
If not already selected, Select Using DHCP in the TCP/IP tab.
4.
Click Save.
Page 218 / 296
Reference Manual for the ProSafe Wireless 802.11g
Firewall/Print Server Model FWG114P v2
C-8
Preparing Your Network
201-10301-02, May 2005
Verifying TCP/IP Properties for Macintosh Computers
After your Macintosh is configured and has rebooted, you can check the TCP/IP configuration by
returning to the TCP/IP Control Panel. From the Apple menu, select Control Panels, then TCP/IP.
The panel is updated to show your settings, which should match the values below if you are using
the default TCP/IP settings that NETGEAR recommends:
•
The IP Address is between 192.168.0.2 and 192.168.0.254
•
The Subnet mask is 255.255.255.0
•
The Router address is 192.168.0.1
If you do not see these values, you may need to restart your Macintosh or you may need to switch
the “Configure” setting to a different option, then back again to “Using DHCP Server”.
Page 219 / 296
Reference Manual for the ProSafe Wireless 802.11g
Firewall/Print Server Model FWG114P v2
Preparing Your Network
C-9
201-10301-02, May 2005
Verifying the Readiness of Your Internet Account
For broadband access to the Internet, you need to contract with an Internet service provider (ISP)
for a single-user Internet access account using a cable modem or DSL modem. This modem must
be a separate physical box (not a card) and must provide an Ethernet port intended for connection
to a Network Interface Card (NIC) in a computer. Your firewall does not support a USB-connected
broadband modem.
For a single-user Internet account, your ISP supplies TCP/IP configuration information for one
computer. With a typical account, much of the configuration information is dynamically assigned
when your PC is first booted up while connected to the ISP, and you will not need to know that
dynamic information.
In order to share the Internet connection among several computers, your firewall takes the place of
the single PC, and you need to configure it with the TCP/IP information that the single PC would
normally use. When the firewall’s Internet port is connected to the broadband modem, the firewall
appears to be a single PC to the ISP. The firewall then allows the computers on the local network to
masquerade as the single PC to access the Internet through the broadband modem. The method
used by the firewall to accomplish this is called Network Address Translation (NAT) or IP
masquerading.
Are Login Protocols Used?
Some ISPs require a special login protocol, in which you must enter a login name and password in
order to access the Internet. If you normally log in to your Internet account by running a program,
such as WinPOET or EnterNet, then your account uses PPP over Ethernet (PPPoE).
When you configure your router, you will need to enter your login name and password in the
router’s configuration menus. After your network and firewall are configured, the firewall will
perform the login task when needed, and you will no longer need to run the login program from
your PC. It is not necessary to uninstall the login program.
What Is Your Configuration Information?
More and more, ISPs are dynamically assigning configuration information. However, if your ISP
does not dynamically assign configuration information but instead uses fixed configurations, your
ISP should have given you the following basic information for your account:
Page 220 / 296
Reference Manual for the ProSafe Wireless 802.11g
Firewall/Print Server Model FWG114P v2
C-10
Preparing Your Network
201-10301-02, May 2005
•
An IP address and subnet mask
•
A gateway IP address, which is the address of the ISP’s router
•
One or more domain name server (DNS) IP addresses
•
Host name and domain suffix
For example, your account’s full server names may look like this:
mail.xxx.yyy.com
In this example, the domain suffix is
xxx.yyy.com
.
If any of these items are dynamically supplied by the ISP, your firewall automatically acquires
them.
If an ISP technician configured your PC during the installation of the broadband modem, or if you
configured it using instructions provided by your ISP, you need to copy the configuration
information from your PC’s Network TCP/IP Properties window or Macintosh TCP/IP Control
Panel before reconfiguring your PC for use with the firewall. These procedures are described next.
Obtaining ISP Configuration Information for Windows Computers
As mentioned above, you may need to collect configuration information from your PC so that you
can use this information when you configure the FWG114P v2 Wireless Firewall/Print Server.
Following this procedure is only necessary when your ISP does not dynamically supply the
account information.
To get the information you need to configure the firewall for Internet access:
1.
On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2.
Double-click the Network icon.
The Network window opens, which displays a list of installed components.
3.
Select TCP/IP, and then click Properties.
The TCP/IP Properties dialog box opens.
4.
Select the IP Address tab.
If an IP address and subnet mask are shown, write down the information. If an address is
present, your account uses a fixed (static) IP address. If no address is present, your account
uses a dynamically-assigned IP address. Click “Obtain an IP address automatically”.
5.
Select the Gateway tab.

Rate

4 / 5 based on 1 vote.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top