1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. FSM7328S
    5. /
  5. 34
Page 166 / 400 Scroll up to view Page 161 - 165
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
8-98
Switching Commands
202-10088-01, March 2005
Mode
Interface Config
set garp timer leave all
This command sets the GVRP leave time for all ports. Leave time is the time to wait after
receiving an unregister request for a VLAN or a multicast group before deleting the VLAN entry.
This can be considered a buffer time for another station to assert registration for the same attribute
in order to maintain uninterrupted service.time is 20 to 600 (centiseconds). The value 60
centiseconds is 0.6 seconds.
Note:
This command has an effect only when GVRP is enabled.
Default
60
Format
set garp timer leave all <
20-600>
Mode
Global Config
no set garp timer leave all
This command sets the GVRP leave time for all ports to the default 60 centiseconds (0.6 seconds).
Note:
This command has an effect only when GVRP is enabled.
Format
no set garp timer leave all
Mode
Global Config
set garp timer leaveall
This command sets how frequently
Leave All PDUs
are generated per port. A
Leave All PDU
indicates that all registrations will be unregistered. Participants would need to rejoin in order to
maintain registration. The value applies per port and per GARP participation. The time may range
from 200 to 6000 (centiseconds). The value 1000 centiseconds is 10 seconds.
Note:
This command has an effect only when GVRP is enabled.
Default
1000
Format
set garp timer leaveall <
200-6000>
Mode
Interface Config
no set garp timer leaveall
This command sets how frequently
Leave All PDUs
are generated per port to 1000 centiseconds (10
seconds). .
Page 167 / 400
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
Switching Commands
8-99
202-10088-01, March 2005
Note:
This command has an effect only when GVRP is enabled
.
Format
no set garp timer leaveall
Mode
Interface Config
set garp timer leaveall all
This command sets how frequently
Leave All PDUs
are generated for all ports. A
Leave All PDU
indicates that all registrations will be unregistered. Participants would need to rejoin in order to
maintain registration. The value applies per port and per GARP participation. The time may range
from 200 to 6000 (centiseconds). The value 1000 centiseconds is 10 seconds.
Note:
This command has an effect only when GVRP is enabled
.
Default
1000
Format
set garp timer leaveall all <
200-6000>
Mode
Global Config
no set garp timer leaveall all
This command sets how frequently
Leave All PDUs
are generated for all ports to 1000 centiseconds
(10 seconds). .
Note:
This command has an effect only when GVRP is enabled.
Format
no set garp timer leaveall all
Mode
Global Config
show garp
This command displays Generic Attributes Registration Protocol (GARP) information.
Format
show garp
Mode
Privileged EXEC and User EXEC
GMRP Admin Mode
This displays the administrative mode of GARP Multicast Registration Protocol
(GMRP) for the system.
GVRP Admin Mode
This displays the administrative mode of GARP VLAN Registration Protocol
(GVRP) for the system
Page 168 / 400
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
8-100
Switching Commands
202-10088-01, March 2005
GARP VLAN Registration Protocol (GVRP) Commands
This chapter provides a detailed explanation of the GVRP commands. The commands are divided
into two functional groups:
•
Show commands display switch settings, statistics, and other information.
•
Configuration commands configure features and options of the switch. For every
configuration command, there is a show command that displays the configuration setting.
set gvrp adminmode
This command enables GVRP.
Default
disabled
Format
set gvrp adminmode
Mode
Privileged EXEC
no set gvrp adminmode
This command disables GVRP.
Format
no set gvrp adminmode
Mode
Privileged EXEC
set gvrp interfacemode
This command enables GVRP (GARP VLAN Registration Protocol) for a specific port.
Default
disabled
Format
set gvrp interfacemode
Mode
Interface Config
no set gvrp interfacemode
This command disables GVRP (GARP VLAN Registration Protocol) for a specific port. If GVRP
is disabled, Join Time, Leave Time and Leave All Time have no effect.
Format
no set gvrp interfacemode
Mode
Interface Config
Page 169 / 400
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
Switching Commands
8-101
202-10088-01, March 2005
set gvrp interfacemode all
This command enables GVRP (GARP VLAN Registration Protocol) for all ports.
Default
disabled
Format
set gvrp interfacemode all
Mode
Global Config
no set gvrp interfacemode all
This command disables GVRP (GARP VLAN Registration Protocol) for all ports. If GVRP is
disabled, Join Time, Leave Time and Leave All Time have no effect.
Format
no set gvrp interfacemode all
Mode
Global Config
show gvrp configuration
This command displays Generic Attributes Registration Protocol (GARP) information for one or
all interfaces.
Format
show gvrp configuration
{<
slot/port
> | all}
Mode
Privileged EXEC and User EXEC
Interface
Valid slot and port number separated by forward slashes.
Join Timer
Specifies the interval between the transmission of GARP PDUs registering (or
re-registering) membership for an attribute. Current attributes are a VLAN or
multicast group. There is an instance of this timer on a per-Port, per-GARP par-
ticipant basis. Permissible values are 10 to 100 centiseconds (0.1 to 1.0 sec-
onds). The factory default is 20 centiseconds (0.2 seconds). The finest
granularity of specification is 1 centisecond (0.01 seconds).
Leave Timer
Specifies the period of time to wait after receiving an unregister request for an
attribute before deleting the attribute. Current attributes are a VLAN or multi-
cast group. This may be considered a buffer time for another station to assert
registration for the same attribute in order to maintain uninterrupted service.
There is an instance of this timer on a per-Port, per-GARP participant basis. Per-
missible values are 20 to 600 centiseconds (0.2 to 6.0 seconds). The factory
default is 60 centiseconds (0.6 seconds). The finest granularity of specification
is 1 centisecond (0.01 seconds).
LeaveAll Timer
This Leave All Time controls how frequently LeaveAll PDUs are generated. A
LeaveAll PDU indicates that all registrations will shortly be deregistered. Par-
ticipants will need to rejoin in order to maintain registration. There is an
Page 170 / 400
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
8-102
Switching Commands
202-10088-01, March 2005
instance of this timer on a per-Port, per-GARP participant basis. The Leave All
Period Timer is set to a random value in the range of LeaveAllTime to
1.5*LeaveAllTime. Permissible values are 200 to 6000 centiseconds (2 to 60
seconds). The factory default is 1000 centiseconds (10 seconds). The finest
granularity of specification is 1 centisecond (0.01 seconds).
Port GMRP Mode
Indicates the GMRP administrative mode for the port. It may be enabled or dis-
abled. If this parameter is disabled, Join Time, Leave Time and Leave All Time
have no effect. The factory default is disabled.
GARP Multicast Registration Protocol (GMRP) Commands
This chapter provides a detailed explanation of the GMRP commands. The commands are divided
into two functional groups:
•
Show commands display switch settings, statistics, and other information.
•
Configuration commands configure features and options of the switch. For every
configuration command, there is a show command that displays the configuration setting.
set gmrp adminmode
This command enables GARP Multicast Registration Protocol (GMRP) on the system. The default
value is disable.
Format
set gmrp adminmode
Mode
Privileged EXEC
no set gmrp adminmode
This command disables GARP Multicast Registration Protocol (GMRP) on the system.
Format
no set gmrp adminmode
Mode
Privileged EXEC

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top