1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. FSM7328
    5. /
  5. 12
Page 56 / 400 Scroll up to view Page 51 - 55
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
6-2
Quick Start up
202-10088-01, March 2005
System Info and System Setup
Quick Start up Software Version Information
Quick Start up Physical Port Data
Table 6-1.
Quick Start up Software Version Information
Command
Details
show hardware
(in Privileged EXEC)
Allows the user to see the software version the device contains
Machine Model (The type and number of ports the device provides.)
For example:
Machine Model FSM7328S
24 = 24 10/100 ports
04 = 4 Uplink ports on front of switch
Table 6-2.
Quick Start up Physical Port Data
Command
Details
show port all
(in Privileged EXEC)
Displays the Ports
slot/port
Type - Indicates if the port is a special type of port
Admin Mode - Selects the Port Control Administration State
Physical Mode - Selects the desired port speed and duplex mode
Physical Status - Indicates the port speed and duplex mode
Link Status - Indicates whether the link is up or down
Link Trap - Determines whether or not to send a trap when link status
changes
LACP Mode - Displays whether LACP is enabled or disabled on this
port.
Page 57 / 400
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
Quick Start up
6-3
202-10088-01, March 2005
Quick Start up User Account Management
Quick Start up IP Address
To view the network parameters the operator can access the device by the following three
methods.
•
Simple Network Management Protocol - SNMP
•
Telnet
•
Web Browser
Table 6-3.
Quick Start up User Account Management
Command
Details
show users
(in Privileged EXEC)
Displays all of the users that are allowed to access the switch
Access Mode - Shows whether the user is able to change
parameters on the switch(Read/Write) or is only able to view
then (Read Only).
As a factory default, admin has Read/Write access and guest
has Read Only access. There can only be one Read/Write user
and up to 5 Read Only users.
show loginsession
(in User EXEC)
Displays all of the login session information
users passwd <
username>
(in Global Config)
Allows the user to set passwords or change passwords needed
to login
A prompt will appear after the command is entered requesting
the users old password. In the absence of an old password
leave the area blank. The operator must press enter to execute
the command.
The system then prompts the user for a new password then a
prompt to confirm the new password. If the new password and
the confirmed password match a message will be displayed.
User password should not be more than eight characters in
length.
copy system:running-config
nvram:startup-config
(in Privileged EXEC)
This will save passwords and all other changes to the device.
If you do not save config, all configurations will be lost when a
power cycle is performed on the switch or when the switch is
reset
logout
(in User EXEC and Privileged
EXEC)
Logs the user out of the switch
Page 58 / 400
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
6-4
Quick Start up
202-10088-01, March 2005
Note:
The user should do a
copy system:running-config nvram:startup-config
after
configuring the network parameters so that the configurations are not lost.
Note:
The IP address assigned to
network
in the above table will not be routable. If access to
management CPU via the routable interface is desired, use the
ip
command.
Table 6-4.
Quick Start up IP Address
Command
Details
show network
(in User EXEC)
Displays the Network Configurations
IP Address - IP Address of the interface
Default IP is 0.0.0.0
Subnet Mask - IP Subnet Mask for the interface
Default is 0.0.0.0
Default Gateway - The default Gateway for this interface
Default value is 0.0.0.0
Burned in MAC Address - The Burned in MAC Address used for in-
band connectivity
Locally Administered MAC Address - Can be configured to allow a
locally administered MAC address
MAC Address Type - Specifies which MAC address should be used for
in-band connectivity
Network Configurations Protocol Current - Indicates which network
protocol is being used
Default is none
Management VLAN Id - Specifies VLAN id
Web Mode - Indicates whether HTTP/Web is enabled.
Java Mode - Indicates whether java mode is enabled.
network parms
(in Privileged EXEC)
network parms <ipaddr
> <netmask> [<gateway>]
IP Address range from 0.0.0.0 to 255.255.255.255
Subnet Mask range from 0.0.0.0 to 255.255.255.255
Gateway Address range from 0.0.0.0 to 255.255.255.255
Page 59 / 400
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
Quick Start up
6-5
202-10088-01, March 2005
Quick Start up Uploading from Switch to Out-of-Band PC (Only
XMODEM)
Quick Start up Downloading from Out-of-Band PC to Switch
(Only XMODEM)
Table 6-5.
Quick Start up Uploading from Switch to Out-of-Band PC (XMODEM)
Command
Details
copy {
nvram:startup-config |
nvram:errorlog |
nvram:msglog |
nvram:traplog} <url>
The types are:
config - configuration file
errorlog - error log
system trace - system trace
traplog - trap log
The URL must be specified as:
xmodem:filepath/fileName
This starts the upload and also displays the mode of
uploading and the type of upload it is and confirms the
upload is taking place.
For example:
If the user is using HyperTerminal, the user must
specify where the file is going to be received by the
PC.
Table 6-6.
Quick Start up Downloading from Out-of-Band PC to Switch (Only XMODEM)
Command
Details
copy <url> {nvram:startup-config |
system:image}
Sets the download datatype to be an image or
config file.
The URL must be specified as:
xmodem:filepath/fileName
For example:
If the user is using HyperTerminal, the user
must specify which file is to be sent to the
switch.
The Switch will restart automatically once the
code has been downloaded.
Page 60 / 400
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
6-6
Quick Start up
202-10088-01, March 2005
Quick Start up Downloading from TFTP Server
Before starting a TFTP server download, the operator must complete the Quick Start up for the IP
Address.
Quick Start up Factory Defaults
Table 6-7.
Quick Start up Downloading from TFTP Server
Command
Details
copy <url> {nvram:startup-config |
system:image}
Sets the download datatype to be an image
or config file.
The URL must be specified as:
tftp://ipAddr/filepath/fileName.
The nvram:startup-config option downloads
the config file using tftp and system:image
option downloads the code file.
Table 6-8.
Quick Start up Factory Defaults
Command
Details
clear config
Enter yes when the prompt pops up to clear all the configurations
made to the switch.
copy system:running-config
nvram:startup-config
Enter yes when the prompt pops up that asks if you want to save
the configurations made to the switch.
reload OR Cold Boot the Switch
Enter yes when the prompt pops up that asks if you want to reset
the system.
This is the users choice either reset the switch or cold boot the
switch, both work effectively.

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top