1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. DGND3300v2
    5. /
  5. 25
Page 121 / 177 Scroll up to view Page 116 - 120
Chapter 7.
Advanced Settings (Part 1)
|
121
N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual
Figure 59.
3.
Click
Add Priority Rule
. The QoS - Priority Rules screen displays.
4.
In the Priority Category
list, either use the default selection of
Applications
,
or select
Online
Gaming
. A drop-down list of predefined applications or games is available.
Figure 60.
5.
You can select an existing item, or you can scroll to the bottom of the list and select
Add a
New Application
or
Add a New Game
.
a.
If you choose to add a new entry, the screen expands as shown:
Figure 61.
Downloaded from
www.Manualslib.com
manuals search engine
Page 122 / 177
122
|
Chapter 7.
Advanced Settings (Part 1)
N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual
b.
In the QoS Policy for field, enter a descriptive name for the new application or game.
c.
Select the connection type, either TCP, UDP, or both (TCP/UDP), and specify the
port number or range of port numbers used by the application or game.
6.
From the Priority
drop-down list, select the priority that this traffic should receive relative to
other applications and traffic when accessing the Internet. The options are Low, Normal,
High, and Highest.
7.
Click
Apply
to save this rule to the QoS Policy list and return to the QoS Setup screen.
8.
In the QoS Setup screen, select the
Turn Internet Access QoS On
check box.
9.
Click
Apply
.
QoS for a Router LAN Port
To create a QoS policy for a device connected to one of the router’s LAN ports:
1.
From the main menu, select
Advanced > QoS Setup
. The QoS Setup screen displays.
2.
Click
Setup QoS Rule
.
3.
In the Priority Category
field, select
Ethernet LAN Port
. The screen changes:
Figure 62.
4.
In the LAN Ports
list, select the LAN port that will have a QoS policy.
5.
From the Priority
drop-down list, select the priority that this port’s traffic should receive
relative to other applications and traffic when accessing the Internet. The options are Low,
Normal, High, and Highest.
6.
Click
Apply
to save this rule to the QoS Policy list and return to the QoS Setup screen.
7.
In the QoS Setup screen, select the
Turn Internet Access QoS On
check box.
8.
Click
Apply
.
QoS for a MAC Address
To create a QoS policy for traffic from a specific MAC address:
1.
From the main menu, select
Advanced > QoS Setup
. The QoS Setup screen displays.
2.
Click
Add Priority Rule
.
3.
In the Priority Category
field, select
MAC Address
. The screen changes:
Downloaded from
www.Manualslib.com
manuals search engine
Page 123 / 177
Chapter 7.
Advanced Settings (Part 1)
|
123
N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual
Figure 63.
4.
If the device to be prioritized appears in the MAC Device List, select it. The information from
the MAC Device List is used to populate the policy name, MAC Address, and Device Name
fields. If the device does not appear in the MAC Device List, click
Refresh
. If it still does not
appear, you must complete these fields manually.
5.
From the Priority
drop-down list, select the priority that this device’s traffic should receive
relative to other applications and traffic when accessing the Internet. The options are Low,
Normal, High, and Highest.
6.
Click
Apply
to save this rule to the QoS Policy list and return to the QoS Setup screen.
7.
In the QoS Setup screen, select the
Turn Internet Access QoS On
check box.
8.
Click
Apply
.
Editing or Deleting an Existing QoS Policy
To edit or delete an existing QoS policy:
1.
From the main menu, select
Advanced > QoS Setup
. The QoS Setup screen displays.
2.
Select the radio button for the QoS policy to be edited or deleted, and do one of the
following:
•
Click
Delete
to remove the QoS policy.
•
Click
Edit
to edit the QoS policy. Follow the instructions in the preceding sections to
change the policy settings.
3.
Click
Apply
in the QoS Setup screen to save your changes.
Configuring Static Routes
Static routes provide additional routing information to your N300 wireless modem router.
Under usual circumstances, the N300 wireless modem router has adequate routing
information after it has been configured for Internet access, and you do not need to configure
additional static routes. You must configure static routes only for unusual cases such as
multiple routers or multiple IP subnets located on your network.
As an example of when a static route is needed, consider the following case:
Downloaded from
www.Manualslib.com
manuals search engine
Page 124 / 177
124
|
Chapter 7.
Advanced Settings (Part 1)
N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual
•
Your primary Internet access is through a cable modem to an ISP.
•
You have an ISDN router on your home network for connecting to the company where
you are employed. This router’s address on your LAN is
1
92.168.0.100.
•
Your company’s network address is 134.177.0.0.
When you first configured your N300 wireless modem router, two implicit static routes were
created. A default route was created with your ISP as the gateway, and a second static route
was created to your local network for all 192.168.0.x addresses. With this configuration, if you
attempt to access a device on the 134.177.0.0 network, your N300 wireless modem router
forwards your request to the ISP. The ISP forwards your request to the company where you
are employed, and the request is likely to be denied by the company’s firewall.
In this case you must define a static route, telling your N300 wireless modem router that
134.177.0.0 should be accessed through the ISDN router at 192.168.0.100.
In this example:
•
The Destination IP Address and IP Subnet Mask fields specify that this static route applies
to all 134.177.x.x addresses.
•
The Gateway IP Address field specifies that all traffic for these addresses should be
forwarded to the ISDN router at 192.168.0.100.
•
A Metric value of 1 will work since the ISDN router is on the LAN.
•
Private is selected only as a precautionary security measure in case RIP is activated.
From the main menu, select
Advanced > Static Routes
. The Static Routes screen displays.
Figure 64.
To add or edit a static route:
1.
Click
Add
to open the Static Routes screen.
Figure 65.
Downloaded from
www.Manualslib.com
manuals search engine
Page 125 / 177
Chapter 7.
Advanced Settings (Part 1)
|
125
N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual
2.
In the Route Name field, type a name for this static route. (This is for identification purposes
only.)
3.
Select the
Private
check box if you want to limit access to the LAN only. If Private is
selected, the static route is not reported in RIP.
4.
Select the
Active
check box to make this route effective.
5.
Type the destination IP address of the final destination.
6.
Type the IP subnet mask for this destination.
If the destination is a single host, type
255.255.255.255
.
7.
Type the gateway IP address, which must be a router on the same LAN segment as the
N300 wireless modem router.
8.
Type a number between 1 and 15 as the metric value.
This represents the number of routers between your network and the destination. Usually,
a setting of 2 or 3 works, but if this is a direct connection, set it to 1.
9.
Click
Apply
to have the static route entered into the table.
Wireless Repeating (Also Called WDS)
The N300 Wireless Modem Router can be used with a wireless access point (AP) to build
large bridged wireless networks. Wireless repeating is a type of Wireless Distribution System
(WDS).
WARNING!
If you use the wireless repeating function, your options for
wireless security are limited to None or WEP. For more
information about wireless security, see
Chapter 2, Wireless
Settings
.
Downloaded from
www.Manualslib.com
manuals search engine

Rate

3.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top