Page 221 / 312 Scroll up to view Page 216 - 220
6.
In the
IP Address
field, enter the LAN IP address for the
modem router
.
7.
In the
IP Subnet Mask
, enter the LAN subnet mask for the
modem router
.
8.
Click the
Apply
button.
Your settings are saved.
If you changed the LAN IP address of the
modem router
, you are disconnected when the changes
take effect.
To reconnect, close your browser, relaunch it, and log in to the
modem router
at its new LAN IP
address.
Manage the Router Information Protocol Settings
Router Information Protocol (RIP) lets the
modem router
exchange routing information with other routers.
By default, RIP is enabled in both directions (in and out) without a particular RIP version.
To manage the RIP settings:
1.
Launch an Internet browser from a computer or WiFi device that is connected to the network.
2.
Type
.
Manage the WAN and LAN Network Settings
221
Nighthawk AC1900 WiFi VDSL/ADSL Modem Router Model D7000
Page 222 / 312
A login window opens.
3.
Enter the user name and password for the
modem router
.
The user name is
admin
. The default password is
password
. The user name and password are
case-sensitive.
4.
Click the
OK
button.
The BASIC Home page displays.
5.
Select
ADVANCED > Setup > LAN Setup
.
The LAN Setup page displays.
6.
From the
RIP Direction
menu, select an RIP direction:
Both
.The
modem router
broadcasts its routing table periodically and incorporates information that
it receives. This is the default setting.
Out Only
. The
modem router
broadcasts its routing table periodically but does not incorporate the
RIP information that it receives.
In Only
.The
modem router
incorporates the RIP information that it receives but does not broadcast
its routing table.
7.
From the
RIP Version
menu, select an RIP version:
Disabled
. The RIP version is disabled. This is the default setting.
RIP-1
. This format is universally supported. It is adequate for most networks, unless you are using
an unusual network setup.
RIP-2
. This format carries more information. Both RIP-2B and RIP-2M send the routing data in
RIP-2 format. RIP-2B uses subnet broadcasting. RIP-2M uses multicasting.
8.
Click the
Apply
button.
Your settings are saved.
Manage Reserved LAN IP Addresses
When you specify a reserved IP address for a computer on the LAN, that computer always receives the
same IP address each time it accesses the
modem router
’s DHCP server.
Reserve a LAN IP address
You can assign a reserved IP address to a computer or server that requires permanent IP settings.
Manage the WAN and LAN Network Settings
222
Nighthawk AC1900 WiFi VDSL/ADSL Modem Router Model D7000
Page 223 / 312
To reserve an IP address:
1.
Launch an Internet browser from a computer or WiFi device that is connected to the network.
2.
Type
.
A login window opens.
3.
Enter the user name and password for the
modem router
.
The user name is
admin
. The default password is
password
. The user name and password are
case-sensitive.
4.
Click the
OK
button.
The BASIC Home page displays.
5.
Select
ADVANCED > Setup > LAN Setup
.
The LAN Setup page displays.
6.
In the Address Reservation section, click the
Add
button.
7.
Either select a device from the Address Reservation Table table by selecting the corresponding radio
button or specify the reserved IP address information:
In the
IP Address
field, enter the IP address to assign to the computer or device.
Choose an IP address from the
modem router
’s LAN subnet, such as 192.168.0.x.
In the
MAC Address
field, enter the MAC address of the computer or device.
In the
Device Name
field, enter the name of the computer or device.
8.
Click the
Add
button.
The reserved address is entered into the table on the LAN Setup page.
The reserved address is not assigned until the next time the computer or device contacts the
modem
router
’s DHCP server. Reboot the computer or device, or access its IP configuration and force a DHCP
release and renew.
Change a Reserved IP Address
You can change a reserved IP address entry.
To change a reserved IP address entry:
1.
Launch an Internet browser from a computer or WiFi device that is connected to the network.
2.
Type
.
Manage the WAN and LAN Network Settings
223
Nighthawk AC1900 WiFi VDSL/ADSL Modem Router Model D7000
Page 224 / 312
A login window opens.
3.
Enter the user name and password for the
modem router
.
The user name is
admin
. The default password is
password
. The user name and password are
case-sensitive.
4.
Click the
OK
button.
The BASIC Home page displays.
5.
Select
ADVANCED > Setup > LAN Setup
.
The LAN Setup page displays.
6.
In the Address Reservation section, select the radio button next to the reserved address.
7.
Click the
Edit
button.
The Edit page displays.
8.
Change the settings.
9.
Click the
Apply
button.
Your settings are saved.
Remove a Reserved IP Address Entry
You can remove a reserved IP address entry.
To remove a reserved IP address entry:
1.
Launch an Internet browser from a computer or WiFi device that is connected to the network.
2.
Type
.
A login window opens.
3.
Enter the user name and password for the
modem router
.
The user name is
admin
. The default password is
password
. The user name and password are
case-sensitive.
4.
Click the
OK
button.
The BASIC Home page displays.
5.
Select
ADVANCED > Setup > LAN Setup
.
The LAN Setup page displays.
6.
In the Address Reservation section, select the radio button next to the reserved address.
7.
Click the
Delete
button.
Manage the WAN and LAN Network Settings
224
Nighthawk AC1900 WiFi VDSL/ADSL Modem Router Model D7000
Page 225 / 312
The address entry is removed.
Change the
Modem Router
’s Device Name
The
modem router
’s device name is
D6100
.This device name displays in a file manager when you browse
your network.
To change the
modem router
’s device name:
1.
Launch an Internet browser from a computer or WiFi device that is connected to the network.
2.
Type
.
A login window opens.
3.
Enter the user name and password for the
modem router
.
The user name is
admin
. The default password is
password
. The user name and password are
case-sensitive.
4.
Click the
OK
button.
The BASIC Home page displays.
5.
Select
ADVANCED > Setup > LAN Setup
.
The LAN Setup page displays.
6.
In the
Device Name
field, enter a new name.
7.
Click the
Apply
button.
Your settings are saved.
Manage the DHCP Server Address Pool
By default, the
modem router
acts as a Dynamic Host Configuration Protocol (DHCP) server.The
modem
router
assigns IP, DNS server, and default gateway addresses to all computers that are connected to its
LAN and WiFi network. The assigned default gateway address is the LAN address of the
modem router
.
These addresses must be part of the same IP address subnet as the
modem router
’s LAN IP address.
The default DHCP address pool is 192.168.0.2–192.168.0.254.
The
modem router
delivers the following parameters to any LAN device that requests DHCP:
Manage the WAN and LAN Network Settings
225
Nighthawk AC1900 WiFi VDSL/ADSL Modem Router Model D7000

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top