1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. D7000
    5. /
  5. 43
Page 211 / 312 Scroll up to view Page 206 - 210
Change the Physical WAN Connection Preference
The
modem router
can autodetect the type of WAN connection. However, you can also set the WAN
connection preference manually to either the DSL port or the Ethernet WAN port.
The
modem router
does not support load balancing over DSL and Ethernet WAN
interfaces. Only
one
WAN interface (either the DLS port or the Ethernet WAN port)
can be active at any time.
Note
To change the WAN connection preference:
1.
Launch an Internet browser from a computer or WiFi device that is connected to the network.
2.
Type
.
A login window opens.
3.
Enter the user name and password for the
modem router
.
The user name is
admin
. The default password is
password
. The user name and password are
case-sensitive.
4.
Click the
OK
button.
The BASIC Home page displays.
5.
Select
ADVANCED > Setup > WAN Setup
.
The WAN Setup page displays.
6.
From the
WAN Preference
menu, select one of the following options:
•
Auto-Detect
. The
modem router
automatically detects whether the WAN connection is DSL over
the DLS port or Ethernet over the Internet port.
Auto-Detect
is the default setting.
•
Must use DSL WAN
.The
modem router
uses the DSL port for a DSL WAN connection.The Internet
port is shut down.
•
Must use Ethernet WAN
.The
modem router
uses the Internet port for an Ethernet WAN connection.
The DSL port is shut down.
7.
Click the
Apply
button.
Your settings are saved.
Manage the WAN and LAN Network Settings
211
Nighthawk AC1900 WiFi VDSL/ADSL Modem Router Model D7000
Page 212 / 312
Enable and Configure a VLAN
A network of computers and devices can behave as if they were connected to the same network even
though they might actually be physically on different segments of a LAN. Virtual LANs (VLANs) are
configured through software rather than hardware, which makes them very flexible.
If you enable a VLAN and if the network devices (hubs and switches) on your LAN support the VLAN
(802.1Q) standard, the VLAN ID for the wireless access point is associated with all traffic coming from
the modem router.
If you are subscribed to IPTV service, the
modem router
might require VLAN tags to distinguish between
the Internet traffic and the IPTV traffic.
For information about enabling and configuring the virtual IPTV interface, see one of the following sections:
•
Manually Set Up an ADSL Internet Connection
on page 51
•
Manually Set Up a VDSL Internet Connection
on page 63
•
Manually Set Up a Cable or Fiber Internet Connection
on page 73
If your ISP provides directions for how to set up VLANs for IPTV and Internet service,
follow those directions.
Note
To enable and configure a VLAN for the virtual Internet interface and another VLAN for the virtual
IPTV interface:
1.
Launch an Internet browser from a computer or WiFi device that is connected to the network.
2.
Type
.
A login window opens.
3.
Enter the user name and password for the
modem router
.
The user name is
admin
. The default password is
password
. The user name and password are
case-sensitive.
4.
Click the
OK
button.
The BASIC Home page displays.
5.
Select
BASIC > Internet
.
Manage the WAN and LAN Network Settings
212
Nighthawk AC1900 WiFi VDSL/ADSL Modem Router Model D7000
Page 213 / 312
6.
Configure a VLAN for the virtual Internet interface:
a.
Make sure that
Internet
is selected from the menu above the
Enable This Interface
check box
and that the
Enable This Interface
check box is selected for the virtual Internet interface (it is by
default).
b.
Select the
Use VLANID
check box.
c.
Enter a VLAN ID that applies to the virtual Internet interface.
The VLAN ID can be in a range from 0 to 4094. The default VLAN ID is 10.
d.
To specify a priority for the VLAN, in the
Priority (0 ~ 7)
field, enter a value from 0 to 7.
e.
Click the
Apply
button.
Your settings are saved for the virtual Internet interface.
7.
From the menu above the
Enable This Interface
check box, select
IPTV
.
Manage the WAN and LAN Network Settings
213
Nighthawk AC1900 WiFi VDSL/ADSL Modem Router Model D7000
Page 214 / 312
The previous figure shows only the top of the Internet Setup page.
8.
Configure a VLAN for the virtual IPTV interface:
a.
Make sure that the
Enable This Interface
check box is selected for the virtual IPTV interface.
If you already enabled and configured the virtual IPTV interface, the check box is selected.
b.
Select the
Use VLANID
check box.
c.
Enter a VLAN ID that applies to the virtual IPTV interface.
The VLAN ID can be in a range from 0 to 4094. The default VLAN ID is 0.
d.
To specify a priority for the VLAN, in the
Priority (0 ~ 7)
field, enter a value from 0 to 7.
e.
Click the
Apply
button.
Your settings are saved for the virtual IPTV interface.
For information about enabling bridge mode for the IPTV virtual interface, see
Enable
Bridge Mode for IPTV Devices
on page 215.
Note
Manage the WAN and LAN Network Settings
214
Nighthawk AC1900 WiFi VDSL/ADSL Modem Router Model D7000
Page 215 / 312
Enable Bridge Mode for IPTV Devices
Some devices, such as an IPTV, cannot function behind the
modem router
’s network address translation
(NAT) service or firewall. Based on what your Internet service provider (ISP) requires, for the device to
connect to the ISP’s network directly, you can enable the bridge between the device and the
modem
router
’s IPTV virtual interface. In bridge mode, by default, the LAN 4 port on the back panel of the
modem
router
is bound to the IPTV virtual interface.
In addition to connecting an IPTV device to the LAN 4 port, you can connect an IPTV device to the LAN
3 port and another one to the LAN 2 port.That is, the
modem router
can support up to three IPTV devices.
The LAN 1 port is reserved for a wired Internet connection. Do not connect an IPTV device to the LAN 1
port.
For information about enabling and configuring the virtual IPTV interface, see one of the following sections:
•
Manually Set Up an ADSL Internet Connection
on page 51
•
Manually Set Up a VDSL Internet Connection
on page 63
•
Manually Set Up a Cable or Fiber Internet Connection
on page 73
To enable bridge mode for one or more IPTV devices:
1.
Launch an Internet browser from a computer or WiFi device that is connected to the network.
2.
Type
.
A login window opens.
3.
Enter the user name and password for the
modem router
.
The user name is
admin
. The default password is
password
. The user name and password are
case-sensitive.
4.
Click the
OK
button.
The BASIC Home page displays.
5.
Select
BASIC > Internet
.
The Internet Setup page displays.
6.
From the menu above the
Enable This Interface
check box, select
IPTV
.
Manage the WAN and LAN Network Settings
215
Nighthawk AC1900 WiFi VDSL/ADSL Modem Router Model D7000

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top