Page 46 / 69 Scroll up to view Page 41 - 45
46
NetComm NF2 User Guide
www.netcommlimited.com
YML27
System Time
The NF2 router time can be synchronised either to a local PC or using NTP (Network Time Protocol) settings to a standard global
internet time. These settings will affect functions such as System Log statistics, scheduling and Firewall settings
Figure 42: Advanced - Advanced Settings -System Time
OPTION
DEFINITION
Time Zone
Select the GMT offset for your location.
Auto-Synchronization
Select an NTP (Network Time Protocol) time server to synchronise to the global internet time with.
Sync with Time Server
Select this button to initiate the router time synchronisation to the specified network time server above.
Sync with my PC
Select this button to initiate the router time synchronization to the computer you are currently logged into the
router with.
Table 28: Advanced - Advanced Settings - System Time
Scheduling
The NF2 has built in scheduling, allowing the router to be switched on or off. This offers a means of parental control. To create a
schedule, ensure the enable Schedule option is selected and press the Add New button.
Figure 43: Advanced - Advanced Settings
Schedule
Page 47 / 69
www.netcommlimited.com
NF2
Dual Band Wi-Fi Gigabit Hub User Guide
47
YML38
Adding a Schedule
Figure 44: Advanced - Advanced Settings - Adding a Schedule
OPTION
DEFINITION
Name of Rule
Enter a name for the Schedule.
Policy
Use the Policy option to set each rule defined to Activate or Deactivate the router except the selected days and
hours below.
Week Day
Select the day(s) of the week you wish the rule to be used on.
Start Time (hh:mm)
Enter the Start time for the rule to begin.
End Time (hh:mm)
Enter the End time for the rule to end.
Table 29: Advanced - Advanced settings - Adding a Schedule Settings
Page 48 / 69
48
NetComm NF2 User Guide
www.netcommlimited.com
YML27
IPv6
The NF2 router can be configured to use IPV6 routing configuration.
Figure 45: Advanced - Advanced Settings - IPV6
OPTION
DEFINITION
IPv6
The option to enable or disable IPv6.
IPv6 Connection
Select the type of IPv6 for the router to use. Options include :
Dynamic DHCPv6 - an IPv6 address is assigned by the router automatically,
Static IPv6 - a static IPv6 address assigned by an Internet Service Provider can be assigned
to the router.
PPPoE
for using an IPv6 address over PPPoE.
6 to 4
This option converts an IPv6 address to an IP v4 address.
IPv6 in IPv4 tunnel
This option uses an IPv6 address through an IPv4 tunnel.
DNS Setting
Select Obtain a DNS Server address automatically assigned by the router or assign your own static Primary
and Secondary DNS addresses.
LAN IPv6 Address
Enter the local IPv6 address in this field.
Auto-configuration
Select to enable auto configuration of the IPv6 address.
Auto-configuration Type
Select either Stateless or Stateful IPv6 auto configuration. Stateless Address Auto configuration (or SLAAC) can
be used by devices connecting to a routed network using
Internet Control Message Protocol version 6
(ICMPv6) router discovery messages
.
This is generally streamlined and simplified compared to Stateful Auto-
configuration. Stateful IPv6 also known as DHCPv6 uses a dedicated configuration mechanism that is more
comprehensive than Stateless Auto configuration catering to all the information needs in the form of required
parameters to the network devices
Router Advertisement lifetime
When a computer host first connects to the NF2 router using IPv6 it sends a link-local router solicitation
multicast request for its configuration parameters. If the NF2 router is configured correctly it will respond with a
router advertisement packet that contains network-layer configuration parameters. The Router advertisement
lifetime is the amount of time that the router advertisement is broadcast as a multicast after receiving the
request.
Table 30: Advanced - Advanced Settings
IPv6 Settings
Page 49 / 69
www.netcommlimited.com
NF2
Dual Band Wi-Fi Gigabit Hub User Guide
49
YML38
TR-069
The TR-069 (technical report 069) protocol uses a SOAP/HTTP protocol to provide communications between Customer-Premises
Equipment (CPE) and an Auto-Configuration Server (ACS) for the purpose of automated configuration of the CPE devices.
Figure 46: Advanced - Advanced Settings - TR-069
OPTION
DEFINITION
TR-069
Select the enable option to enable the TR-069 protocol on the NF2.
ACS URL
Enter the URL of the Auto-Configuration Server in this field.
ACS UserName
Enter the user name of the Auto-Configuration Server here.
ACS Password
Enter the password of the Auto-Configuration Server here.
Connection Request Port
Enter the port number to be used by a CPE in sending an Inform message to the ACS server to initialise a
connection.
Connection Request
UserName
Enter the Connection Request username to be used by each of the CPE devices to authenticate with the ACS
server.
Connection Request Password
Enter the Connection Request password to be used by each of the CPE devices to authenticate with the ACS
server.
Inform
Set the Inform to enable or disable to accept or deny an inform message from a CPE device to the ACS server.
Interval
Enter the interval in seconds between Inform messages being sent to the ACS server.
Table 31: Advanced - Advanced Settings - TR-069
Page 50 / 69
50
NetComm NF2 User Guide
www.netcommlimited.com
YML27
VLAN
The VLAN section of the NF2 allows for the creation of a virtual LAN across one or more of the Ethernet and wireless interfaces
Figure 47: Advanced
Advanced Settings
VLAN
Enter the Virtual ID for each Ethernet port and tick whether the data transmitted needs to be tagged, a part of VLAN tagging.
For WAN VLAN settings press the WAN VLAN Settings button.
Figure 48: Advanced - Advanced Settings - VLAN - WAN VLAN
Select the appropriate VID (Virtual ID) and select the Routing Type, either NAT or Bridging. Press the Save button to save any
changes to the settings.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top