When a more secure connection is needed, you can change the wireless security settings on the NB7Plus4W to
WPA2-PSK.
Please follow the following steps:
1.
Connect the computer directly to the modem using Ethernet cable.
2.
Open the web configuration, http://192.168.1.1/ from your web browser i.e. Internet explorer, Firefox.
3.
At the log in screen, enter the Username and password. The default Username is “admin” and the default
password is “admin”. Then click on “Login”.
4.
Click on “Wireless” and then click on “Security”
5.
In the Wireless > Security page, change Network Authentication to “WPA2-PSK”
6.
Enter the key in “WPA2 Pre-Shared Key” field. The key needs to be more than 8 digits and less than 63
digits and it can be any combination of letters and numbers.
7.
Change the WPA2 Group Rekey Interval to “3600”
8.
Click on “Save/Apply”
Page 57 / 60
YML901 Rev1
NB7 Series User Guide
NB7 Series User Guide
www.netcomm.com.au
³7
NB7 Series
How to Bridge my
NB7 Series Modem
Please see the instructions below in order to bridge your NB7 Series Modem/Router:
1.
Open your Web Browser (such as Internet Explorer), and enter the following numbers into the Address Bar:
192.168.1.1
If asked to login, the default username and password is
admin
and
admin
.
2.
Click on
Quick Setup
from the left menu.
3.
Change
DHCP
from
enabled
to
disabled
.
4.
Select
Bridging
and then press
Save and Reboot
.
The modem will now save it’s settings, and reboot itself. Please wait for 2 minutes while this process completes.
After 2 minutes, the modem will have rebooted, and will now be in Bridge Mode.
You can now connect the NB7 Series Modem into your router, and setup the router in
PPPoE
mode.
Page 58 / 60
NB7 Series User Guide
YML901 Rev1
³´
www.netcomm.com.au
Legal & Regulatory
Information
This manual is copyright. Apart from any fair dealing for the purposes of private study, research, criticism or review, as permitted under the Copyright
Act, no part may be reproduced, stored in a retrieval system or transmitted in any form, by any means, be it electronic, mechanical, recording or
otherwise, without the prior written permission of NetComm Limited. NetComm Limited accepts no liability or responsibility, for consequences arising
from the use of this product.
NetComm Limited reserves the right to change the specifications and operating details of this product without notice.
NetComm is a registered trademark of NetComm Limited.
All other trademarks are acknowledged the property of their respective owners.
Customer Information
ACA (Australian Communications Authority) requires you to be aware of the following information and warnings:
1.
This unit shall be connected to the Telecommunication Network through a line cord which meets the requirements of the ACA TS008 Standard.
2.
This equipment has been tested and found to comply with the Standards for C-Tick and or A-Tick as set by the ACA . These standards are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio noise and, if not installed and used in accordance with the instructions detailed within this manual, may cause interference to
radio communications. However, there is no guarantee that interference will not occur with the installation of this product in your home or
office. If this equipment does cause some degree of interference to radio or television reception, which can be determined by turning the
equipment off and on, we encourage the user to try to correct the interference by one or more of the following measures:
•
Change the direction or relocate the receiving antenna.
•
Increase the separation between this equipment and the receiver.
•
Connect the equipment to an alternate power outlet on a different power circuit from that to which the receiver/TV
is connected.
•
Consult an experienced radio/TV technician for help.
3.
The power supply that is provided with this unit is only intended for use with this product. Do not use this power supply with any other
product or do not use any other power supply that is not approved for use with this product by NetComm. Failure to do so may cause
damage to this product, fire or result in personal injury.
Page 59 / 60
YML901 Rev1
NB7 Series User Guide
NB7 Series User Guide
www.netcomm.com.au
³9
NB7 Series
Product Warranty
The warranty is granted on the following conditions:
1.
This w
arranty extends to the original purchaser (you) and is not transferable;
2.
This warranty shall not apply to software programs, batteries, power supplies, cables or other accessories supplied in or with the product;
3.
The customer complies with all of the terms of any relevant agreement with NetComm and any other reasonable requirements of NetComm
including producing such evidence of purchase as NetComm may require;
4.
The cost of transporting product to and from NetComm’s nominated premises is your responsibility; and,
5.
NetComm does not have any liability or responsibility under this warranty where any cost, loss, injury or damage of any kind, whether direct,
indirect, consequential, incidental or otherwise arises out of events beyond NetComm’s reasonable control. This includes but is not limited
to: acts of God, war, riot, embargoes, acts of civil or military authorities, fire, floods, electricity outages, lightning, power surges, or shortages
of materials or labour.
6.
The customer is responsible for the security of their computer and network at all times. Security features may be disabled within the factory
default
settings. NetComm recommends that you enable these features to enhance your security.
The warranty is automatically voided if:
1.
You, or so
meone else, use the product, or attempts to use it, other than as specified by NetComm;
2.
The fault or defect in your product is the result of a voltage surge subjected to the product either by the way of power supply or
communication line, whether caused by thunderstorm activity or any other cause(s);
3.
The fault is the result of accidental damage or damage in transit, including but not limited to liquid spillage;
4.
Your product has been used for any purposes other than that for which it is sold, or in any way other than in strict accordance with the user
manual supplied;
5.
Your product has been repaired or modified or attempted to be repaired or modified, other than by a qualified person at a service centre
authorised by NetComm; and,
6.
The serial nu
mber has been defaced or altered in any way or if the serial number plate has been removed.
Limitations of Warranty
The Trade Practices Act 1974 and corresponding State and Territory Fair Trading Acts or legalisation of another Government (“the relevant acts”) in
certain circumstances imply mandatory conditions and warranties which cannot be excluded. This warranty is in addition to and not in replacement
for such conditions and warranties.
To the extent permitted by the Relevant Acts, in relation to your product and any other materials provided with the product (“the Goods”) the liability
of NetComm under the Relevant Acts is limited at the option of NetComm to:
•
Replacement of the Goods; or
•
Repair of the Goods; or
•
Payment of the cost of replacing the Goods; or
•
Payment of the cost of having the Goods repaired.
All NetComm ACN 002 490 486 products have a standard 12 months warranty from date of purchase. However some products have an
extended warranty option (refer to packaging). To be eligible for the extended warranty you must supply the requested warranty information
to NetComm within 30 days of the original purchase by registering on-line via the NetComm web site at
19216811.live