1. Home
    2. /
  2. Manuals
    3. /
  3. NetComm
    4. /
  4. N900
    5. /
  5. 7
Page 31 / 69 Scroll up to view Page 26 - 30
www.netcommlimited.com
NF2
–
Dual Band Wi-Fi Gigabit Hub User Guide
31
YML38
VPN
–
IPSec
This page allows the NetComm NF2 to act as a VPN IPSec endpoint. Internet Protocol Security (IPsec) is used to secure IP (Internet
Protocol) communications by authenticating and encrypting each IP packet of a communication session. IPsec also includes
protocols for establishing mutual authentication between agents at the beginning of the session and negotiation of cryptographic
keys to be used during the session.
Figure 21: Advanced - Network Setup - IPSec
OPTION
DEFINITION
VPN-IPSEC
Select this checkbox to enable the router as a VPN-IPSec endpoint.
Netbios over IPSEC
Select this checkbox to enable Netbios over IPSEC.
NAT Traversal
Select this option to enable NAT Traversal of the IPSec connection.
VPN Statistic
Select this field to enable VPN statistics
–
including the VPN tunnel name, elapsed time of the VPN tunnel,
incoming and outgoing packets.
Max. Number of Tunnels
Enter the maximum number of VPN tunnels that can be created at any one time.
Dynamic VPN
This field will create a VPN tunnel using dynamic IP addresses.
Table 17: Advanced - Network Setup -VPN-IPSec
Page 32 / 69
32
NetComm NF2 User Guide
www.netcommlimited.com
YML27
VPN
–
IPSec Tunnel Setup
This page allows you to configure a VPN endpoint IPSec.
Figure 22: Advanced - Network Setup - Dynamic IPSec
OPTION
DEFINITION
Tunnel Name
Enter the VPN tunnel name.
Local Subnet
Enter the Local Subnet address.
Local Network
Enter the Local Network address.
Phase 1 Key Life Time
Enter the Phase 1 Key Life Time in seconds.
Phase 2 Key Life Time
Enter the time in seconds for the Phase 2 Key Life Time.
Encapsulation Protocol
Enter the encapsulation protocol for the VPN tunnel. Options are ESP (Encapsulated Security Payload), AH
(Authentication Header) or ESP + AH.
PFS Group
Select the PFS (Perfect Forward secrecy) Group to be used.
Remote ID
Enter the remote ID and select the Remote ID type. Options include Username, FQDN (Fully Qualified Domain
Name), User@FQDN or Key ID.
Local ID
Enter the local ID and select the local ID type. Options include Username, FQDN (Fully Qualified Domain Name),
User@FQDN or Key ID
Dead Peer Detection (DPD)
Select to enable Dead Peer Detection, a means of detecting a dead IKE (Internet Key Exchange) peer. Set the
timeout and delay in seconds.
Set IKE Proposal
Select to Enable IKE (Internet Key Exchange) Proposals.
Table 18: Advanced - Network Setup - VPN IPSec - Dynamic IPSec
Page 33 / 69
www.netcommlimited.com
NF2
–
Dual Band Wi-Fi Gigabit Hub User Guide
33
YML38
VPN-L2TP
This page allows you to configure a Layer 2 Tunnelling protocol. It does not provide any encryption or confidentiality by itself; it relies
on an encryption protocol that it passes within the tunnel to provide privacy.
Figure 23: Advanced - Network Setup - L2TP
VPN-PPTP Client
The Point-to-Point Tunnelling Protocol (PPTP) is a method for implementing virtual private networks. PPTP uses a control channel
over TCP and a GRE tunnel operating to encapsulate PPP packets.
Figure 24: Advanced - Network Setup - PPTP Client
Page 34 / 69
34
NetComm NF2 User Guide
www.netcommlimited.com
YML27
VPN
–
PPTP Server
This page allows the NetComm NF2 to become a PPTP VPN endpoint.
Figure 25: Advanced - Network Setup - VPN - PPTP Server
OPTION
DEFINITION
VPN-PPTP Server
Select this option to enable the VPN-PPTP Server function.
Server Virtual IP
Enter the IP address of the PPTP server.
IP Pool Start Address
The starting IP address for the DHCP pool, in the above example is 192.168.0.10.
IP Pool End Address
The ending IP address for the DHCP pool, in the above example is 192.168.0.100
Authentication Protocol
Select the authentication protocol you wish to use.
MPPE Encryption Mode
Select to enable MPPE Encryption Mode (Microsoft Point-to-Point Encryption).
NAT
Select to enable NAT on the PPTP server.
Encryption length
Enter encryption length for the packets sent through the VPN tunnel.
Table 19: Advanced - Network Setup - VPN - PPTP Server Settings
Page 35 / 69
www.netcommlimited.com
NF2
–
Dual Band Wi-Fi Gigabit Hub User Guide
35
YML38
Change Password
This page allows you to change the administrator username and password to secure the NetComm NF2 management console
against unauthorised access.
Figure 26: Advanced - Network Setup - Change Password

Rate

3.5 / 5 based on 2 votes.

Popular NetComm Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top