1. Home
    2. /
  2. Manuals
    3. /
  3. MediaLink
    4. /
  4. MWN-WAPR300N
    5. /
  5. 6
Page 26 / 67 Scroll up to view Page 21 - 25
MWN-WAPR300N
21
Upload/Download:
specifies the traffic direction for the selected IP addresses.
Bandwidth Range:
The maximum and minimum upload/download data traffic of
the hosts in specified IP range. The unit is KByte/sec. The uplink of upload and
download cannot exceed the WAN port bandwidth limitation range (by default is
1500 or 1492).
Enable:
enables the current edited rule. Otherwise, the rule will not go into
effect.
Add to list:
After you edit the rule, click the “
Add to list
” button to add the current
rule to the rule list.
Here we take 2Mbps bandwidth as an example. Theoretically, the biggest downloading
rate for 2Mbps bandwidth is 2Mbps=256KByte/s, and the biggest uploading rate is
512kbps=64KByte/s
Example 1
If you want to set the download rate of the computer at the IP address of 192.168.8.2 as
80-90KByte/s, upload rate as 10-15KByte/s, first add one upload rule as shown in the
picture below:
1. Enter 192.168.8.2 in the both IP address fields
2. Select upload in the Upload/Download field.
3. Enter 10-15 in the bandwidth range field
4. Select “Enable”
5. Click “Add to list”
6. Click “Apply” to finish the upload rule settings.
Page 27 / 67
MWN-WAPR300N
22
And then add a download rule as shown in the picture below.
1. Enter 192.168.8.2 in the both IP address fields
2. Select download in the Upload/Download field.
3. Enter 80-90 in the bandwidth range field
4. Select “Enable”
5. Click “Add to list”
6. Click “Apply” to finish the download rule settings.
Example 2
Set the download rate of all computers within the range of
192.168.8.2--192.168.8.254 as 100-120KByte/s, and the upload rate as 20-30KByte/s,
as shown in the picture below.
Upload Rule:
Page 28 / 67
MWN-WAPR300N
23
Download Rule:
4.8 Traffic Statistics
Traffic statistics is used to display the bandwidth that LAN devices have used.
Enable Traffic Statistics
: Enable the Medialink router to calculate the traffic used by the
LAN devices. By default, Traffic Statistics is disabled to improve the router’s data packet
processing ability. When this function is enabled, the webpage will refresh automatically
every five minutes, meanwhile, each computer’s traffic value will refresh automatically.
IP Address:
The IP address of the device whose traffic is being calculated.
Page 29 / 67
MWN-WAPR300N
24
Uplink Rate:
The data speed of data sent from the device per second, the unit is
KByte/s.
Downlink Rate:
The data speed of data received by the device per second, the
unit is KByte/s.
Sent Message:
The number of the calculated data packets that are sent out
through the router.
Sent Bytes:
The volume of the calculated device’s statistics that is sent out
through the router.
Received Message:
The number of the calculated data packets that are received
through the router.
Received Bytes:
The volume of the calculated device’s statistics that is received
through the router.
4.9 Firewall
This page allows you to disable/enable the router’s Firewall.
Page 30 / 67
MWN-WAPR300N
25
4.10 WAN Medium Type / Range Extender
Wired WAN and Wireless WAN
Wired WAN:
In this mode, a network cable is directly connected to the WAN port. Wired
WAN is the default mode.
Wireless WAN
: This mode can be used if your ISP provides a wireless connection
service or if you want to use it to amplify your existing wireless network.
SSID
: SSID (Service Set Identifier) is the identity of the wireless device to which you
wish to connect the Medialink router. Click the “Open Scan” button to let the router
automatically search for an SSID.
MAC
: To connect to the wireless device, the device’s MAC Address must be in this field.
Click the “Open Scan” button to let the router automatically search for the wireless
device’s MAC.
Channel
: The wireless device’s communication channel. You must select the same
channel as the connecting wireless device to enable their communications. Click the
“Open Scan” button to see the channel of the connecting wireless network.
Security Mode
: This must be set to the same security mode that is used by the
connecting device. The Medialink router must have the same Security Mode, Algorithm
or Encryption Mode and Key as the wireless device. These must be entered manually. If
the security settings are not entered correctly, the Medialink router will not be able to
communicate with the wireless device.

Rate

3.5 / 5 based on 2 votes.

Popular MediaLink Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top