1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. SRW2024P
    5. /
  5. 9
Page 41 / 110 Scroll up to view Page 36 - 40
32
Chapter 5: Using the Web-based Utility for Configuration
Port Management Tab - Link Aggregation
24-Port 10/100/1000 Gigabit Switch with Webview and PoE
Type.
The type of LAG is displayed here.
Link Status
. The link status is displayed here.
Speed
. The connection speed is displayed here.
Duplex
. The connection duplex is displayed here.
Flow Control
. This is the flow control status of the LAG. It is active when the port uses Full Duplex Mode.
Create
. To create a new LAG, click the
Create
button in the Create column, then add members to the LAG by
clicking on the
Select Member
button. The select member screen for the Link Aggregation opens.
Detail
button. To configure the LAG and the LAG broadcast control, click the
Detail
button. The detail screen for
the LAG opens. Assign up to 8 ports to the LAG by selecting the ports, then click
Apply
.
Figure 5-8: Link Aggregation - Link Aggregation Select
Member
Figure 5-7: Port Management - Link Aggregration
Figure 5-9: Link Aggregation - Link Aggregation Detail
Downloaded from
www.Manualslib.com
manuals search engine
Page 42 / 110
33
Chapter 5: Using the Web-based Utility for Configuration
Port Management Tab - LACP
24-Port 10/100/1000 Gigabit Switch with Webview and PoE
Port Management Tab - LACP
Ports can be statically grouped into an aggregate link (that is, LAG) to increase the bandwidth of a network
connection or to ensure fault recovery. Or you can use the Link Aggregation Control Protocol (LACP) to
automatically negotiate a LAG link between the Switch and another network device. For static LAGs, the switches
have to comply with the Cisco EtherChannel standard. For dynamic LAGs, the switches have to comply with LACP.
This Switch supports up to eight LAGs. For example, a LAG consisting of two 1000 Mbps ports can support an
aggregate bandwidth of 4 Gbps when operating at full duplex.
To avoid creating a loop in the network, be sure you enable LACP before connecting the ports, and also
disconnect the ports before disabling LACP.
Global Setting
System Priority.
Indicates the global LACP priority value. The possible range is 1- 65535. The default value is 1.
Port Setting
Set the System Priority and Port Priority for the Port Actor. After you have completed setting the port LACP
parameters, click
Save Settings
.
Port.
Defines the port number to which timeout and priority values are assigned.
Status
. Select
Enabled
to enable the port.
Set Port Actor
. This menu sets the local side of an aggregate link; that is, the ports on this Switch.
Port Priority.
Defines the LACP priority value for the port. The field range is 1-65535.
LACP Timeout.
Administrative LACP timeout. A short or long timeout value can be selected. Long is the default.
Figure 5-10: Port Management - LACP
Downloaded from
www.Manualslib.com
manuals search engine
Page 43 / 110
34
Chapter 5: Using the Web-based Utility for Configuration
Port Management Tab - PoE Power Settings
24-Port 10/100/1000 Gigabit Switch with Webview and PoE
Port Management Tab - PoE Power Settings
If a device is connected to a Switch port and the Switch detects that it requires more than the power budget of
the port, no power is supplied to the device (that is, port power remains off).
If the power demand from devices connected to Switch ports exceeds the power budget set for the Switch, the
port power priority settings are used to control the supplied power.
Select
Enabled
to enable PoE power on selected ports, set the priority using the drop-down menu provided, and
set the power allocation for each port.
Port
. Displays the port number.
Admin Status
. Select
Enabled
to enable PoE power to be supplied to the connected device.
Priority
. Set the priority of the supply using the drop-down menu.
Power Allocation
(3000-15400 milliwatts). Set the maximum power that can be supplied to the port.
Mode
. Displays whether the connected PoE device is on or off.
Power Consumption
(milliwatts). Displays the power currently being used by the connected PoE device.
Figure 5-11: Port Management - PoE Power Settings
Downloaded from
www.Manualslib.com
manuals search engine
Page 44 / 110
35
Chapter 5: Using the Web-based Utility for Configuration
VLAN Management Tab - Create VLAN
24-Port 10/100/1000 Gigabit Switch with Webview and PoE
VLAN Management Tab - Create VLAN
The Create VLAN screen provides information and global parameters for configuring and working with VLANs.
Single VLAN
VLAN ID (2-4094).
Indicates the ID number of the VLAN being configured. Up to 256 VLANs can be created. This
field is used to add VLANs one at a time. To add the defined VLAN ID number, press the
Add
button.
VLAN Name.
Displays the user-defined VLAN name.
VLAN Range
VLAN Range.
Indicates a range of VLANs being configured. To add the defined range of VLAN ID numbers, press
the
Add Range
button.
VLAN Table
The VLAN Table displays a list of all configured VLANs. The VLAN ID, VLAN Name, and status of the VLAN are
displayed here. To remove a VLAN, click the
Remove
button.
VLAN Management Tab - Port Settings
The VLAN Port Settings screen provides parameters for managing ports that are part of a VLAN. The port default
VLAN ID (PVID) is configured on the VLAN Port Settings screen. All untagged packets arriving to the device are
tagged by the ports PVID.
Port.
The port number included in the VLAN.
Mode.
Indicates the port mode. Possible values are:
•
General.
The port belongs to VLANs, and each VLAN is user-defined as tagged or untagged (full 802.1Q
mode).
•
Access.
The port belongs to a single untagged VLAN. When a port is in Access mode, the packet types
which are accepted on the port (packet type) cannot be designated. It is also not possible to enable/
disable ingress filtering on an access port.
•
Trunk.
The port belongs to VLANs in which all ports are tagged (except for an optional single native VLAN).
Figure 5-12: VLAN Management - Create VLAN
NOTE:
VLANs that are created dynamically using
GVRP are assigned a VLAN name “Undefined”.
Figure 5-13: VLAN Management - Port Settings
Downloaded from
www.Manualslib.com
manuals search engine
Page 45 / 110
36
Chapter 5: Using the Web-based Utility for Configuration
VLAN Management Tab - Ports to VLAN
24-Port 10/100/1000 Gigabit Switch with Webview and PoE
Acceptable Frame Type.
Packet type accepted on the port. Possible values are:
•
Admit Tag Only.
Indicates that only tagged packets are accepted on the port.
•
Admit All.
Indicates that both tagged and untagged packets are accepted on the port.
PVID.
Assigns a VLAN ID to untagged packets. The possible values are 2 to 4094. VLAN 4095 is defined as per
standard and industry practice as the discard VLAN. Packets classified to the Discard VLAN are dropped.
Ingress Filtering.
Enables or disables Ingress filtering on the port. Ingress filtering discards packets which do
not include an ingress port.
LAG.
Indicates the LAG to which the VLAN is defined.
VLAN Management Tab - Ports to VLAN
Use the Port to VLAN screen to configure port members for the selected VLAN index. Assign ports as tagged if
they are connected to 802.1Q VLAN compliant devices, or untagged they are not connected to any VLAN-aware
devices.
Select VLAN.
Select the VLAN number. from the drop-down menu.
Switch Port Mode
Indicates VLAN membership mode for an interface. (Default: Access
Access.
Indicates the port belongs to a single untagged VLAN. When a port is in Access mode, the packet types
which are accepted on the port cannot be designated. Ingress filtering cannot be enabled/disabled on an access
port.
Trunk.
Indicates the port belongs to VLANs in which all ports are tagged, except for one port that can be
untagged.
General.
Indicates the port belongs to VLANs, and each VLAN is user-defined as tagged or untagged (full 802.1Q
mode).
Membership
Select VLAN membership for each interface by marking the appropriate radio button for a port or LAG:
Excluded.
Excludes the interface from the VLAN. However, the interface can be added to the VLAN through GVRP.
Figure 5-14: VLAN Management - Ports to VLAN
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4 / 5 based on 1 vote.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top