1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. SRW2008
    5. /
  5. 11
Page 51 / 81 Scroll up to view Page 46 - 50
Chapter 5
Advanced Configuration
45
8-Port 10/100/1000 Gigabit Switch with Webview
Root
•
Provides the lowest cost path to forward packets
to root device.
Designated
•
Indicates the port or LAG via which the
designated device is attached to the LAN.
Alternate
•
Provides an alternate path to the root
device from the root interface.
Backup
•
Provides a backup path to the designated
port path toward the Spanning Tree leaves. Backup
ports occur only when two ports are connected in a
loop by a point-to-point link. Backup ports also occur
when a LAN has two or more connections connected
to a shared segment.
Disabled
•
Indicates the port is not participating in the
Spanning Tree.
Mode
Indicates the current Spanning Tree mode. The
Spanning Tree mode is selected in the Global STP screen.
The possible field values are:
Classic STP
•
Indicates that Classic STP is enabled on
the device.
Rapid STP
•
Indicates that Rapid STP is enabled on the
device.
Multiple STP
•
Indicates that Multiple STP is enabled
on the device.
Interface Priority
Defines the interface priority for
specified instance. The default value is
128
.
Path Cost
Indicates the port contribution to the Spanning
Tree instance. The range should always be 1-200,000,000.
Designated Bridge ID
Indicates that the bridge ID
number that connects the link or shared LAN to the root.
Designated Port ID
Indicates that the Port ID number on
the designated bridge that connects the link or the shared
LAN to the root.
Designated Cost
Indicates that the default path cost
is assigned according to the method selected on the
Spanning Tree Global Settings screen.
Forward Transitions
Indicates the number of times
the port has changed from Forwarding state to Blocking
state.
Remaining Hops
Indicates the hops remaining to the
next destination.
Multicast > IGMP Snooping
Multicast > IGMP Snooping
When IGMP Snooping is enabled globally, all IGMP packets
are forwarded to the CPU. The CPU analyzes the incoming
packets and determines:
Which ports want to join which Multicast groups?
•
Which ports have Multicast routers generating IGMP
•
queries?
Which routing protocols are forwarding packets and
•
Multicast traffic?
Ports requesting to join a specific Multicast group issue an
IGMP report, specifying that Multicast group is accepting
members. This results in the creation of the Multicast
filtering database.
Enable IGMP Snooping
Indicates if IGMP Snooping is
enabled on the device. IGMP Snooping can be enabled
only if Bridge Multicast Filtering is enabled.
VLAN ID
Specifies the VLAN ID.
IGMP Status
Indicates if IGMP snooping is enabled on
the VLAN.
Auto Learn
Indicates if Auto Learn is enabled on the
device. If Auto Learn is enabled, the device automatically
learns where other Multicast groups are located. Enables
or disables Auto Learn on the Ethernet device.
Host Timeout
Indicates the amount of time host waits to
receive a message before timing out. The default time is
260
seconds.
MRouter Timeout
Indicates the amount of the time the
Multicast router waits to receive a message before it times
out. The default value is
300
seconds.
Page 52 / 81
Chapter 5
Advanced Configuration
46
8-Port 10/100/1000 Gigabit Switch with Webview
Leave Timeout
Indicates the amount of time the host
waits, after requesting to leave the IGMP group and not
receiving a Join message from another station, before
timing out. If a Leave Timeout occurs, the switch notifies
the Multicast device to stop sending traffic The Leave
Timeout value is either user-defined, or an immediate
leave value. The default timeout is
10
seconds.
Multicast > Bridge Multicast
Multicast > Global Settings
The
Bridge Multicast
screen displays the ports and LAGs
attached to the Multicast service group in the Ports and
LAGs tables. The Port and LAG tables also reflect the
manner in which the port or LAGs joined the Multicast
group. Ports can be added either to existing groups or to
new Multicast service groups. The Bridge Multicast screen
permits new Multicast service groups to be created. The
Bridge Multicast screen also assigns ports to a specific
Multicast service address group.
The
Bridge Multicast
screen is divided into two areas,
Configuring Multicast and Multicast Table. The fields are
the same for both areas.
VLAN ID
Identifies a VLAN to be configured to a Multicast
service.
Bridge Multicast Address
Identifies the Multicast group
MAC address/IP address.
Bridge IP Multicast
DIsplays the port that can be added
to a Multicast service.
LAG
Displays LAG that can be added to a Multicast
service.
The configuration options are as follows:
Static
•
Indicates
the
port
is
user-defined.
Dynamic
•
Indicates
the
port
is
configured
dynamically.
Forbidden
•
Forbidden ports are not included the
Multicast group, even if IGMP snooping designated
the port to join a Multicast group.
None
•
The port is not configured for Multicast service.
The
Add to List
button adds the configured RMON event
to the Event Table at the bottom of the screen.
Multicast > Bridge Multicast Forward All
Multicast > Multicast Forward All
The
Bridge Multicast Forward All
screen contains fields
for attaching ports or LAGs to a device that is attached
to a neighboring Multicast router/switch. Once IGMP
Snooping is enabled, Multicast packets are forwarded to
the appropriate port or VLAN.
The
Bridge Multicast Forward All
screen contains the
following fields:
VLAN
ID
DIsplays
the
VLAN
for
which
Multicast
parameters are displayed.
The configuration options are as follows:
None
•
The port is not configured for Multicast service.
Forbidden
•
Forbidden ports are not included the
Multicast group, even if IGMP snooping designated
the port to join a Multicast group.
Static
•
Indicates the port is user-defined.
Dynamic
•
Indicates
the
port
is
configured
dynamically.
SNMP > Global Parameters
The
Global Parameters
screen contains parameters for
defining SNMP notification parameters.
Page 53 / 81
Chapter 5
Advanced Configuration
47
8-Port 10/100/1000 Gigabit Switch with Webview
SNMP > Global Parameters
Local Engine ID
Indicates the local device engine ID. The
field value is a hexadecimal string. Each byte in hexadecimal
character strings consists of two hexadecimal digits. Each
byte can be separated by a period or a colon. The Engine
ID must be defined before SNMPv3 is enabled. For stand-
alone devices, select a default Engine ID that is comprised
of Enterprise number and the default MAC address. For a
stackable system configure the Engine ID, and verify that
the Engine ID is unique for the administrative domain.
This prevents two devices in a network from having the
same Engine ID.
Use Default
Uses the device generated Engine ID. The
default Engine ID is based on the device MAC address and
is defined per standard as:
First 4 octets — first bit = 1, the rest is IANA Enterprise
•
number.
Fifth octet — Set to 3 to indicate the MAC address that
•
follows.
Last 6 octets — MAC address of the device.
•
SNMP Notifications
Indicates if the device can send
SNMP notifications.
Authentication
Notifications
Indicates
if
SNMP
Authentication failure notification is enabled on the
device.
SNMP > Views
SNMP > Views
SNMP Views provide access or block access to device
features or feature aspects. For example, a view can be
defined that states that SNMP Group A has Read Only
(R/O) access to Multicast groups, while SNMP Group B
has Read-Write (R/W) access to Multicast groups. Feature
access is granted via the MIB name, or MIB Object ID.\
View Name
Displays the user-defined views. The options
are as follows:
Default
•
Displays the default SNMP view for read and
read/write views.
DefaultSuper
•
Displays the default SNMP view for
administrator views.
Subtree ID Tree
Indicates the device feature OID included
or excluded in the selected SNMP view. The options to
select the Subtree are as follows:
Select from List
•
Select the Subtree from the list
provided.
Insert
•
Enables a Subtree not included in the Select
from List field to be entered.
View Type
Indicates if the defined OID branch will be
included or excluded in the selected SNMP view.
The
Add to List
button adds the Views configuration to
the Views Table at the bottom of the screen.
Page 54 / 81
Chapter 5
Advanced Configuration
48
8-Port 10/100/1000 Gigabit Switch with Webview
SNMP > Group Profile
SNMP > Group Profile
The
Group Profile
screen provides information for creating
SNMP groups and assigning SNMP access control privileges
to SNMP groups. Groups allow network managers to
assign access rights to specific device features, or features
aspects.
Group Name
Displays the user-defined group to which
access control rules are applied. The field range is up to
30 characters.
Security Model
Defines the SNMP version attached to
the group. The possible field values are:
SNMPv1
•
SNMPv1 is defined for the group.
SNMPv2
•
SNMPv2 is defined for the group.
SNMPv3
•
SNMPv3 is defined for the group.
Security Level
Defines the security level attached to the
group. Security levels apply to SNMPv3 only. The possible
field values are:
No
Authentication
•
Indicates
that
neither
the
Authentication nor the Privacy security levels are
assigned to the group.
Authentication
•
Authenticates SNMP messages, and
ensures the SNMP messages origin is authenticated.
Privacy
•
Encrypts SNMP messages.
Operation
Defines the group access rights. The possible
field values are:
Read
•
The management access is restricted to read-
only, and changes cannot be made to the assigned
SNMP view.
Write
•
The management access is read-write and
changes can be made to the assigned SNMP view.
Notify
•
Sends traps for the assigned SNMP view.
SNMP > Group Membership
SNMP > Group Membership
The
Group Membership
screen provides information
for assigning SNMP access control privileges to SNMP
groups.
User name
Provides a user-defined local user list.
Engine ID
Indicates either the local or remote SNMP entity
to which the user is connected. Changing or removing the
local SNMP Engine ID deletes the SNMPv3 User Database.
Local
•
Indicates that the user is connected to a local
SNMP entity.
Remote
•
Indicates that the user is connected to a
remote SNMP entity. If the Engine ID is defined, remote
devices receive inform messages.
Group Name
Contains a list of user-defined SNMP
groups. SNMP groups are defined in the SNMP Group
Profile page.
Authentication Method
Indicates the Authentication
method used. The possible field values are:
None
•
Indicates that no authentication method is
used to authenticate the port.
MD5 Password
•
Indicates that port authentication
is
performed
via
HMAC-MD5-96
password
authentication.
SHA Password
•
Indicates that port authentication
is
performed
via
HMAC-SHA-96
password
authentication.
MD5
Key
•
Indicates
that
port
authentication
is
performed via the HMAC-MD5 algorithm.
SHA
Key
•
Indicates
that
port
authentication
is
Page 55 / 81
Chapter 5
Advanced Configuration
49
8-Port 10/100/1000 Gigabit Switch with Webview
performed via HMAC-SHA-96 authentication.
Password
Define the local user password. Local user
passwords can contain up to 159 characters.
Authentication
Key
Defines
the
HMAC-MD5-96
or
HMAC-SHA-96 authentication level. The authentication
and privacy keys are entered to define the authentication
key. If only authentication is required, 16 bytes are defined.
If both privacy and authentication are required, 32 bytes
are defined. Each byte in hexadecimal character strings is
two hexadecimal digits. Each byte can be separated by a
period or a colon.
Privacy Key
Defines the Privacy Key (LSB). If only
authentication is required, 20 bytes are defined. If both
privacy and authentication are required, 36 bytes are
defined. Each byte in hexadecimal character strings is
two hexadecimal digits. Each byte can be separated by a
period or colon.
The
Add to List
button adds the Group Membership
configuration to the respective table at the bottom of the
screen.
SNMP > Communities
The
Communities
screen
contains
three
areas,
Communities, Basic Table and Advanced Table.
SNMP > Communities
SNMP Management Station
Defines the management
station
IP
address
for
which
the
advanced
SNMP
community is defined. There are two definition options:
Define the management station IP address.
•
All
•
Includes all management station IP addresses.
Community
String
Defines
the
password
used
to
authenticate the management station to the device.
Basic
Enables SNMP Basic mode for a selected community
and contains the following fields:
Access Mode
Defines the access rights of the community.
The possible field values are:
Read Only
•
Management access is restricted to read-
only, and changes cannot be made to the community.
Read Write
•
Management access is read-write and
changes can be made to the device configuration, but
not to the community.
SNMP
Admin
•
User
has
access
to
all
device
configuration options, as well as permissions to modify
the community.
View Name
Contains a list of user-defined SNMP views.
Advanced
Enables SNMP Advanced mode for a selected
community and contains the following fields:
Group Name
Defines advanced SNMP communities
group names.
The
Add
to
List
button
adds
the
Communities
configuration to the respective Table at the bottom of the
screen.
Base Table
Management Station
Displays the management station
IP address for which the basic SNMP community is
defined.
Community String
Displays the password used to
authenticate the management station to the device.
Access
Mode
Displays
the
access
rights
of
the
community.
View Name
Displays the user-defined SNMP view.
SNMP > Table

Rate

3.5 / 5 based on 2 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top