1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. SPA-841
    5. /
  5. 52
Page 256 / 286 Scroll up to view Page 251 - 255
SPA9000 Field Reference
Voice tab
SPA9000 Voice System Administration Guide
254
B
SIP Debug Option
SIP messages are received at or sent from the proxy listen
port. This feature controls which SIP messages to log.
Choices are as follows:
none—No logging.
1-line—Logs the start-line only for all messages.
1-line excl. OPT—Logs the start-line only for all messages
except OPTIONS requests/responses.
1-line excl. NTFY—Logs the start-line only for all messages
except NOTIFY requests/responses.
1-line excl. REG—Logs the start-line only for all messages
except REGISTER requests/responses.
1-line excl. OPT|NTFY|REG—Logs the start-line only for all
messages except OPTIONS, NOTIFY, and REGISTER
requests/responses.
full—Logs all SIP messages in verbose mode.
full excl. OPT—Logs all SIP messages in full text except
OPTIONS requests/responses.
full excl. NTFY—Logs all SIP messages in full text except
NOTIFY requests/responses.
full excl. REG—Logs all SIP messages in full text except
REGISTER requests/responses.
full excl. OPT|NTFY|REG—Logs all SIP messages in full text
except for OPTIONS, NOTIFY, and REGISTER requests/
responses.
Default:
None
Restrict Source IP
If line interfaces use the same SIP Port value and the Restrict
Source IP feature is enabled, the proxy IP address for Lines 1
and 2 is treated as an acceptable IP address for both lines. To
enable the Restrict Source IP feature, select yes. Otherwise,
select no. A source IP address is untrusted if it does not
match any of the IP addresses resolved from the configured
<Proxy> (or <Outbound Proxy> if <Use Outbound Proxy> is
yes).
Default:
no
Referor Bye Delay
Controls when the SPA9000 sends BYE to terminate stale call
legs upon completion of call transfers. Multiple delay settings
(Referor, Refer Target, Referee, and Refer-To Target) are
configured on this screen. For the Referor Bye Delay, enter
the appropriate period of time in seconds.
Default:
4
Downloaded from
www.Manualslib.com
manuals search engine
Page 257 / 286
SPA9000 Field Reference
Voice tab
SPA9000 Voice System Administration Guide
255
B
Voice tab > Line page
Subscriber Information section
Refer Target Bye Delay
For the Refer Target Bye Delay, enter the appropriate period
of time in seconds.
Default:
0
Referee Bye Delay
For the Referee Bye Delay, enter the appropriate period of
time in seconds.
Default:
0
Refer-To Target Contact
To contact the refer-to target, select yes. Otherwise, select
no.
Default:
no
Auth INVITE
When enabled, authorization is required for initial incoming
INVITE requests from the SIP proxy.
Display Name
Display name for caller ID.
User ID
User ID assigned by the ITSP, often the same as the DID.
Password
Password for this User ID.
Use Auth ID
To use the authentication ID and password for SIP
authentication, select yes. Otherwise, select no to use the
user ID and password.
Default:
no
Auth ID
Authentication ID for SIP authentication.
Call Capacity
Maximum number of calls allowed on this line interface. You
can set a value from 1 to 15, or leave the setting as unlimited.
Note that the SPA9000 does not distinguish between
incoming and outgoing calls when talking about call capacity.
NOTE
Unlimited = 16.
Default:
unlimited
Contact List
List of client stations that the SPA9000 alerts when there is
an incoming call to the line interface from the ITSP.
Cfwd No Ans Delay
Delay, in seconds, before the call forwarding of no-answer
calls feature is triggered.
Default:
20
Downloaded from
www.Manualslib.com
manuals search engine
Page 258 / 286
SPA9000 Field Reference
Voice tab
SPA9000 Voice System Administration Guide
256
B
Voice tab > Line page
Dial Plan section
Voice tab > Line page
NAT Settings section
Dial Plan
Dial plan script for this line.
Default:
(xx.)
The Dial Plan strips off the steering digit prior to
sending the dialed number to the ITSP.
NAT Mapping Enable
To use externally mapped IP addresses and SIP/RTP ports in
SIP messages, select yes. Otherwise, select no.
Default:
no
NAT Keep Alive Enable
To send the configured NAT keep alive message periodically,
select yes. Otherwise, select no.
Default:
no
NAT Keep Alive Msg
Enter the keep alive message that should be sent
periodically to maintain the current NAT mapping. If the value
is $NOTIFY, a NOTIFY message is sent. If the value is
$REGISTER, a REGISTER message without contact is sent.
Default:
$NOTIFY
NAT Keep Alive Dest
Destination that should receive NAT keep alive messages. If
the value is $PROXY, the messages are sent to the current or
outbound proxy.
Default:
$PROXY
EXT SIP Port
Enter the port number of the external port to substitute for the
actual SIP port of the SPA9000 in all outgoing SIP messages.
Default: blank
Downloaded from
www.Manualslib.com
manuals search engine
Page 259 / 286
SPA9000 Field Reference
Voice tab
SPA9000 Voice System Administration Guide
257
B
Voice tab > Line page
Proxy and Registration section
Proxy
SIP proxy server for all outbound requests.
Default: blank
Outbound Proxy
SIP Outbound Proxy Server where all outbound requests are
sent as the first hop.
Use Outbound Proxy
Enable the use of <Outbound Proxy>. If set to no, <Outbound
Proxy> and <Use OB Proxy in Dialog) is ignored.
Default:
no
Use OB Proxy In Dialog
Whether to force SIP requests to be sent to the outbound
proxy within a dialog. Ignored if <Use Outbound Proxy> is no
or <Outbound Proxy> is empty.
Default:
yes
Register
Enable periodic registration with the <Proxy>. This
parameter is ignored if <Proxy> is not specified.
Default:
yes
Make Call Without Reg
Allow making outbound calls without successful (dynamic)
registration by the unit. If No, dial tone will not play unless
registration is successful.
Default:
no
Register Expires
Allow answering inbound calls without successful (dynamic)
registration by the unit. If proxy responded to REGISTER with
a smaller Expires value, the SPA9000 will renew registration
based on this smaller value instead of the configured value. If
registration failed with an Expires too brief error response,
the SPA9000 will retry with the value given in the Min-Expires
header in the error response.
Default:
3600
Recommended:
60
Ans Call Without Reg
E
xpires value in sec in a REGISTER request. SPA9000 will
periodically renew registration shortly before the current
registration expired. This parameter is ignored if <Register>
is no. Values are yes or no.
Use DNS SRV
Whether to use DNS SRV lookup for Proxy and Outbound
Proxy.
Default:
no
Downloaded from
www.Manualslib.com
manuals search engine
Page 260 / 286
SPA9000 Field Reference
Voice tab
SPA9000 Voice System Administration Guide
258
B
DNS SRV Auto Prefix
If enabled, the SPA9000 will automatically prepend the Proxy
or Outbound Proxy name with _sip._udp when performing a
DNS SRV lookup on that name.
Default:
no
Proxy Fallback Intvl
This parameter sets the delay (sec) after which the SPA9000
will retry from the highest priority proxy (or outbound proxy)
servers after it has failed over to a lower priority server. This
parameter is useful only if the primary and backup proxy
server list is provided to the SPA9000 via DNS SRV record
lookup on the server name. (Using multiple DNS A record per
server name does not allow the notion of priority and so all
hosts are considered at the same priority and the SPA9000
will not attempt to fall back after a fail over).
Default:
3600
Proxy Redundancy
Method
SPA9000 will make an internal list of proxies returned in DNS
SRV records. In normal mode, this list will contain proxies
ranked by weight and priority.
If based on SRV, the port is configured, the SPA9000 does
normal first and also inspects the port number based on 1
st
proxy’s port in the list.
Default:
Normal
Mailbox Status
The status of the connection to the voice mail server
Mailbox status for all the mailboxes associated with this line
interface. The status is automatically updated when the
SPA9000 receives voicemail status notification from the ITSP.
Format: [
mbs
[,
mbs
[,
mbs
[,…]]]] where:
mbs
=
mbid
:
new
/
old
mbid
= mailbox ID, such as 12345
new
= number of new messages in mailbox: 0,1,2,…
old
= number of old messages in mailbox: 0, 1, 2, …
Mailbox Subscribe URL
This parameter allows $USER and $PROXY macros, such as
$USER@$PROXY
Mailbox Deposit URL
This parameter allows $USER, $PROXY, and $MBID macros,
such as $USER@$PROXY, or $MBID@$PROXY.
Default:
blank
Mailbox Subscribe
Expires
Identifies when the mailbox subscription expires.
Recommended:
30
Downloaded from
www.Manualslib.com
manuals search engine

Rate

3.5 / 5 based on 2 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top