Dial Plan 2

:

(000S0<:@gw0>|1800xxxxxxS0<:@gw0>)

Description

:

The above dial plan contains two individual plans, building on from Dial

Plan 1. You will notice that a | separates the 1

st

dial plan from the 2

nd

.The

2

nd

dial plan is used to route 1800 numbers through the your PSTN line. It

works the same way as the 1

st

dial plan, in that when you dial a 1800 number

followed by 6 other digits (0-9) it will be directed through your PSTN line.

Dial Plan 3

:

(<*1:0123456789>)

Description

:

This plan demonstrates replacement. If you dial a * followed by a 1 then the

number 0123456789 would be dialed.

Dial Plan 4

:

(<0:61>[2-9]xxxxxxxxS0)

Description

:

This plan demonstrates replacement and limiting choices. When you dial an 0

followed by a 2,3,4,5,6,7,8 or 9 and then nine of any other digit (0-9) it will

prepend 61 and remove the 0. So if you rang 02 123456789 the actual number

that would be called would be 61 2 123456789.

Dial Plan 5

:

(1900xxxxxx!)

Description

:

This plan demonstrates number barring. If you enter a 1900 followed by 6

more digits (0-9) you call will not be placed.

Dial Plan 6

:

(<#9:>xx.<:@gw0>)

Description

:

This plan demonstrates replacement and repetition. When you enter a #9

followed by any number of digits(a timeout is used to determine the end) it

will go out through the PSTN line (Gateway 0).

Putting it all together

Dial Plan 7

:

(000S0<:@gw0>|1[38]xxx.<:@gw0>|1900xxxxxx!| 0[2-9]xxxxxxxxS0|

<#9:>xx.<:@gw0>)

Description

:

This plan combines elements from all the above dial plans. It routes all 000,

1800, 1300 calls out via the PSTN line. Its bars 1900 numbers. It allows an

Australian land line to be called and it also allows you to select the PSTN line

by dialing a #9.

Appendix B - Factory Reset

To perform a factory reset on your SPA-3000 remove the Ethernet cable and the PSTN line

cable, leaving just the power and the phone connected. Dial **** on the phone. You should hear a

Sipura message asking you to enter your selection. . Then dial 73738#.

WARNING

: This will restore your unit back to factory defaults, all your information will

be lost.

Appendix C - Saving your Configuration

Method 1 – ProgramUtility

There is a utility that has been written to save/restore SPA-3000 configurations. The file is

called NewSipuraUtil and can be downloaded from the following site:

Method 2 - Manually

To save your configuration, log into your SPA-3000 web interface as admin. Change the

view to advanced. Select the

File – Save As

option from your web brower and save the

configuration page to your PC's hard drive. Thats it!

Now to restore settings that you have previously saved, you need to edit the configuration

page that you saved to your PC's hard drive. To do this, find the page on your hard drive, right click

on it and

Open With – Notepad

.

Now, do a search for the following line of code.

<FORM action=”asipua.spa”

...........................

You need to change this line to read:

<FORM action=”http://

IP Address of Sipura

/admin/asipura.spa”

........

Where

IP Address of Sipura

is the IP address of your Sipura SPA-3000.

Now save the page, then load it up in your web browser, when you hit Submit Changes,

your saved configuration will be loaded back into your SPA-3000.

Appendix D – Upgrading Firmware

The latest firmware for the Sipura SPA-3000 can be located on the Sipura support site.

To upgrade the firmware in your SPA-3000 download the latest firmware, unzip it and run

the exe file provided. At the time of writing this document v3.1.7Gwg is the latest firmware,

The first thing that you need to do is enter the IP address of your SPA into the spaces

provided. In the example below the SPA-3000 is located at 192.168.1.10.

Click on the OK button to begin so the program can find your SPA-3000. When the program

locates the SPA, it will interrogate it and you will be shown a confirmation screen.

Click on the Upgrade button to begin the upgrade procedure. The upgrade itself should only

take a minute or so. Whatever you do don't turn the power of during this operation.

Once the procedure has finished, you should be presented with the following screen and

your upgrade has been completed.

Note

: The upgrade procedure does not effect your current settings.