1. Home
    2. /
  2. Manuals
    3. /
  3. Kyocera
    4. /
  4. KR-2
    5. /
  5. 8
Page 36 / 72 Scroll up to view Page 31 - 35
36
of
72
WI-FI PROTECTED SETUP
Wi-Fi Protected Setup
Enable
Enable the Wi-Fi Protected Setup feature.
Lock Wireless Security Settings
Locking the wireless security settings prevents the settings from being changed by any
new external registrar using its PIN. Devices can still be added to the wireless network
using Wi-Fi Protected Setup. It is still possible to change wireless network settings with
Manual Wireless Network Setup
,
Wireless Network Setup Wizard
, or an existing external
WLAN Manager Registrar.
PIN Settings
A PIN is a unique number that can be used to add the router to an existing network or to
create a new network. The default PIN may be printed on the bottom of the router. For
extra security, a new PIN can be generated. You can restore the default PIN at any time.
Only the Administrator ("admin" account) can change or reset the PIN.
Current PIN
Shows the current value of the router's PIN.
Reset PIN to Default
Restore the default PIN of the router.
Generate New PIN
Create a random number that is a valid PIN. This becomes the router's PIN. You can
then copy this PIN to the user interface of the registrar.
Add Wireless Station
This Wizard helps you add wireless devices to the wireless network using the Wi-Fi
Protected Setup protocol.
The wizard will prompt you to enter the PIN for the device, or ask you to press the
configuration button on the device. If the device supports Wi-Fi Protected Setup and has
a configuration button, you can add it to the network by pressing the configuration button
on the device and then the on the router within 60 seconds. The status LED on the router
will flash three times if the device has been successfully added to the network.
There are several ways to add a wireless device to your network. Access to the wireless
network is controlled by a “registrar”. A registrar only allows devices onto the wireless
network if you have entered the PIN, or pressed a special Wi-Fi Protected Setup button
on the device. The router acts as a registrar for the network, although other devices may
act as a registrar as well.
Page 37 / 72
37
of
72
Add Wireless Device Wizard
Start the wizard.
ADVANCED NETWORK
UPnP
UPnP is short for Universal Plug and Play, which is a networking architecture that
provides compatibility among networking equipment, software, and peripherals. This
router has optional UPnP capability, and can work with other UPnP devices and software.
Enable UPnP
If you need to use the UPnP functionality, you can enable it here.
Allow Users to disable Internet Access
Disabling this option prevents UPnP clients from terminating the WAN connection.
Allow Users to modify Virtual Server Mappings
Disabling this option prevents UPnP clients from adding, modifying, deleting, or disabling
virtual server entries.
WAN Ping
Pinging public WAN IP addresses is a common method used by hackers to test whether
your WAN IP address is valid.
Enable WAN Ping Respond
If you leave this option unchecked, you are causing the router to ignore
ping
commands
for the public WAN IP address of the router.
WAN Ping Inbound Filter
Select a filter that controls which WAN computers can use the ping feature. If you do not
see the filter you need in the list of filters, go to the
Advanced
→
Inbound Filter
screen
and create a new filter.
WAN Port Speed
Normally, this is set to "auto". If you have trouble connecting to the WAN, try the other
settings.
Multicast Streams
The router uses the IGMP protocol to support efficient multicasting -- transmission of
identical content, such as multimedia, from a source to a number of recipients.
Enable Multicast Streams
This option must be enabled if any applications on the LAN participate in a multicast
group. If you have a multimedia LAN application that is not receiving content as
expected, try enabling this option.
Page 38 / 72
38
of
72
PPPoE Pass Through
This option controls whether LAN computers can act as PPPoE clients and negotiate the
PPP sessions through the router over the WAN ethernet link.
Enable PPPoE Pass Through
Enabling this option allows LAN computers to act as PPPoE clients. Disabling this option
prevents LAN computers from establishing PPPoE pass-through connections.
FAILOVER
The router can establish an uplink via the ethernet WAN port or any modems plugged into the
USB, ExpressCard or CardBus ports. Although all of these devices may be plugged in, only one
of them may establish a link at a time. If the WAN connection fails the router will automatically
attempt to bring up a new link on another device. This feature is called failover.
WAN Failure Detection
WAN failure detection works by detecting the presence of traffic on the ethernet WAN
link. (Note that this only applies to the ethernet WAN link, not the modems.) If the link is
idle for too long the router will attempt to ping a target IP address. If the ping does not
reply, the router assumes the link is down and attempts to fail over to a modem.
Enable
This enables failure detection on the ethernet link. Even when this is disabled unplugging
the ethernet cable at the WAN port will trigger failover to a modem.
Timeout
If the ethernet link is idle for this amount of time then the router will either send a ping or
failover to a modem.
Enable Ping on Idle
When enabled, the router will send a ping after the link idle timeout. If the ping gets a
reply, the router will restart the idle timer, otherwise it will failover to a modem.
Ping Target
The default ping target is the router's gateway. You may specify a different IP address as
a target here.
WAN Interfaces
This section allows you to change the failover order of devices (aka interfaces); to
monitor their status; to take the active link down; or to bring a link up on another device.
The device at the top of the list has the highest priority. This is the device which the
router will attempt to start when it boots up. If the link cannot be brought up on this
device, or if it goes down later, the router will attempt to bring the link up on the next
available device. Whenever a link fails on a device, the router will always move down to
the next device down in the list, and wrap around again to the top.
Page 39 / 72
39
of
72
Slot
The slot is the physical port the modem or ethernet cable is plugged into.
Device
This shows a description of the device.
Status
This is the link status of a device, which is one of the following.
Ready
This means the device is plugged in and available but not active.
Establishing
This means the router is attempting to bring up the link over the device.
Established
This means the link is up and running on the device.
Suspended
This means the router will not attempt to bring up the link over the device until a timer
expires. This only applies to modems, which must conform to carrier specifications about
how often they may attempt to connect to the network. The timeout depends on how
many previous connection attempts have failed in a row.
Control
The device which has an active link will show a circle-and-slash icon. If you click on this
icon the router will bring the link down. It will not automatically failover in this case.
All other available devices will have a light-bulb icon. If you click on this icon the router
will attempt to bring the link up over this device. If necessary, it will first bring the active
link down. Failover will proceed to the next device down on the list.
Priority
Click on the up- and down-arrow icons to change the priority of the device.
Page 40 / 72
40
of
72
TOOLS HELP
•
Administrator Settings
•
Time
•
Syslog
•
Email Settings
•
System
•
Firmware
•
Dynamic DNS
•
System Check
•
Schedules
ADMINISTRATOR SETTINGS
The Administrator Settings section is used to set-up secure access to the Web-based
management. By default no password is configured. It is highly recommended that you create a
password to keep your new router secure.
System Language
The language in which the router's web pages are displayed in can be changed here.
Admin Password
Enter a password for the user "admin", who will have full access to the Web-based
management interface.
Internet Access Password
Enter a password for the user "user", who will have read-only access to the Web-based
management interface.
Gateway Name
The name of the router can be changed here.
Inactivity Time Out
If the router does not detect any administrative activity (from WAN or LAN) during this
number of minutes, it logs the adminstrator off.
Enable HTTPS Server
Enabling this option makes it possible to perform remote management with the Secure
HTTP (HTTPS) protocol.
Enable Remote Management
Enabling Remote Management allows you to manage the router from anywhere on the
Internet. Disabling Remote Management allows you to manage the router only from
computers on your LAN.

Rate

4 / 5 based on 1 vote.

Popular Kyocera Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top