1. Home
    2. /
  2. Manuals
    3. /
  3. Kozumi
    4. /
  4. KM-400P
    5. /
  5. 4
Page 16 / 48 Scroll up to view Page 11 - 15
The following table describes the fields in this screen.
Label
Description
WAN Connection Type
Select the WAN Connection Type here, you can select
PPPoA
,
PPPoE
,
1483 MER
,
1483 Routed
or
1483 Bridged
.
Encapsulation Mode
Select the method of encapsulation used by your ISP from the drop-down
list box. Choises are
LLC/SNAP
or
VC-Mux
.
< Back
Click
< Back
to return to the previous screen
Next >
Click
Next >
to go to the next screen
If you select PPPoA or PPPoE in WAN Connection Type, click
Next
, the screen of Fig 3.3.1-3 appears as
shown next.
Fig
3.3.1
-3
The following table describes the fields of this screen.
Label
Description
Obtain an IP address
automatically
The dynamic IP is not fixed; your ISP assigns you the different one each
time.
Use the following IP
address
A static IP is a fixed IP that your ISP gives you.
WAN IP Address
Input the IP address of the WAN interface provided by your ISP
Enable NAT
Select it to enable the NAT functions of the MODEM. If you are not to
enable NAT and intend the user of the MODEM to access the Internet
normally, you must add a route on the uplink equipment; otherwise the
access to the Internet will fail. Normally, it is required to enable NAT.
< Back
Click
< Back
to return to the previous screen
Next >
Click
Next >
to go to the next screen
Then click
Next
, the screen of Fig3.3.1-4 appears as shown next.
16
Page 17 / 48
Fig
3.3.1
-4
The following table describes the fields of this screen.
Label
Description
PPP Username
PPP Password
The username and password apply to PPPoE and PPPoA encapsulation
only. Make sure that you have entered the correct username and password.
PPP Connection Type
Choices are
Continuous
,
Connect on Demand
and
Manual
.
< Back
Click
< Back
to return to the previous screen
Next >
Click
Next >
to go to the next screen
Then click Next, the screen of Fig3.3.1-5 appears as shown next.
17
Page 18 / 48
Fig
3.3.1
-5
The following table describes the fields of this screen.
Label
Description
LAN IP
Enter the IP address of your ROUTER in dotted decimal notation, for
example, 192.168.1.1(factory default)
LAN Netmask
Type the subnet mask of LAN IP.
Enable Secondary IP
Select this check box to enable the secondary LAN IP
Secondary LAN IP
Enter the secondary IP address of your ROUTER in dotted decimal
notation, for example, 192.168.100.1(factory default)
Secondary LAN Netmask
Type the subnet mask of the secondary LAN IP
Enable DHCP Server
Select this check box to enable the DHCP Server
Start IP
This field specifies the first of the contiguous addresses in the IP address
pool.
End IP
This field specifies the last of the contiguous addresses in the IP address
pool.
< Back
Click
< Back
to return to the previous screen
Next >
Click
Next >
to go to the next screen
If you finish the settings of this page, click
Next
, the screen appears as shown next.
18
Page 19 / 48
Fig
3.3.1
-7
If you select 1483 MER in Fig 3.3.1-2, the screen appears as shown next.
Fig
3.3.1
-8
The following table describes the fields of this screen.
19
Page 20 / 48
Label
Description
Obtain an IP address
automatically
The MODEM will obtain a (WAN) IP address automatically and at this
time it will enable DHCP Client functions. The WAN IP address is
obtained from the uplink equipment like BAS and the uplink equipment is
required to enable the DHCP Server functions.
Use the following IP
address
If you want to input the WAN ip address by yourself. Check this entry and
then input related data in the field.
WAN IP Address
Input the IP address of the WAN interface provided by your ISP
WAN Subnet Mask
Input the subnet mask concerned to the IP address of the WAN interface
provided by your ISP.
Default Gateway
You can input the IP address of the default gateway by yourself, click this
entry and then input related data in the fields.
Obtain DNS server
addresses automatically
To obtain the IP address of the DNS server assigned by the uplink
equipment such as BAS.
Use the following DNS
server addresses
If you want to input the IP address of the DNS server by yourself, click
this entry and then input related data in the fields.
Primary DNS server
Input the IP address of the primary DNS server here.
Secondary DNS server
Input the IP address of the secondary DNS server provided by your ISP
here.
Enable NAT
Select it to enable the NAT functions of the MODEM. If you are not to
enable NAT and intend the user of the MODEM to access the Internet
normally, you must add a route on the uplink equipment; otherwise the
access to the Internet will fail. Normally, it is required to enable NAT.
< Back
Click
< Back
to return to the previous screen
Next >
Click
Next >
to go to the next screen
If you finish the settings of this page, click Next, the screen of Fig 3.3.1-6 appears. The settings of this
screen, see above paragraphs.
If you select 1483 Routed in Fig 3.3.1-2, the screen of Fig 3.3.1-9 appears as shown next.
Fig
3.3.1
-9
20

Rate

4 / 5 based on 1 vote.

Popular Kozumi Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top