1. Home
    2. /
  2. Manuals
    3. /
  3. Kozumi
    4. /
  4. KM-400P
    5. /
  5. 2
Page 6 / 48 Scroll up to view Page 1 - 5
Items
Usage
Ethernet
Ethernet RJ-45 port
Power On/Off.
Power
Power connector. DC 12 Voltage/1000mA,female pole is
positive.
1.4 System Requirements
Make sure first that you have prepared these following items to guarantee the ROUTER can work normally.
Services subscriptions
An 10BaseT/100BaseT Ethernet card installed on your PC
HUB or Switch. (Attached to several PCs through one of Ethernet interfaces on the device)
Operation system: Windows 98SE, Windows 2000, Windows ME, or Windows XP
Internet Explorer V5.0 or higher, or Netscape V4.0 or higher, or firefox 1.5 or higher.
1.5 Feature
Supports various line modes
Supports external PPPoE dial-up access
Supports internal PPPoE/PPPoA dial-up access
Supports leased line mode
Supports ZIPB (Zero Installation PPP Bridge Mode)
Supports 1483B/1483R/MER access
Supports multiple PVCs(eight at most) and these PVCs can be isolated from each other
Support a single PVC with multiple sessions
Support multiple PVCs with multiple sessions
Supports the binding of the ports and the PVCs
Supports the 802.1Q and 802.1P protocol
Supports DHCP server
Supports NAT/NAPT
Supports static route
Supports firmware upgrade
：
WEB/tftp/ftp
Supports reset to factory default:reset, WEB
Supports DNS relay
Supports Virtual server
Supports DMZ functions
Supports two-level passwords and usernames
Supports WEB interface
Supports telnet CLI
Supports System status display
Supports PPP session PAP/CHAP
Supports IP filter function
6
Page 7 / 48
Supports IP QoS function
Supports remote access control
Supports line connection status test
Supports remote management
（
Telnet; HTTP
）
Supports configuration file backup and restoration function
Ethernet supported such as Crossover Detection & Auto-Correction and polarity correction
Supports UPnP
7
Page 8 / 48
2. Hardware Installation
1
、
Refer to the figure below: Connect the DSL port of the device and the ROUTER port of the splitter with
a telephone cable; connect the phone to the Phone port of the splitter through a cable; connect the incoming
line to the Line port of the splitter.
The splitter has three ports
：
LINE: Connects to a wall phone jack (RJ-11 jack)
ROUTER: Connects to the DSL jack of the device
PHONE: Connects to a telephone set
2
、
Connect the LAN port of the device to the network card of the PC via an Ethernet line (MDI/MDIX).
Note:
Use twisted-pair cables to connect with the HUB/Switch.
3
、
Plug the power adapter to the wall outlet and then connect the other end of it to the PWR port of the
device.
Connection 1:
Fig. 2-1 displays the application diagram for the connection of the Router, PC, splitter and
telephone set
。
Fig 2-1 Connection Diagram
（
Without connecting telephone sets before the splitter
）
Connection 2
：
As illustrated in the following figure, the splitter is installed close to the device.
8
Page 9 / 48
Fig 2-2 Connection Diagram
（
Connecting a telephone set before the splitter
）
It is
recommended
to follow the Connection 1 in an actual connection!
Note:
When Connection 2 is used, the filter must be installed close to the telephone lines. (See Fig.
2-2. Do not use the splitter instead of the filter).
Installing a telephone directly before the splitter may lead to a failure of connection between the device and
the device of LAN side, or cannot access into the Internet, or slow the connection speed if you really need to add
a telephone set before the splitter, you have to add a MicroFilter before connecting to a telephone set. Do not
connect several telephones before the splitter. Moreover, do not connect several telephones with MicroFilters.
9
Page 10 / 48
3. Introducing the Web Configurator
3.1 How to access ROUTER
The following introductions are prepared for the first time users, it is a detail “How-To” user
guide.
1
、
Open IE browser
，
then enter
in address bar.
2
、
You are required to enter user name and password. See the Fig 3.1-1.
The super user name and password is admin/admin
The common user name and password is user/user
Fig 3.1-1
3
、
If you enter as super user, the below screen will be displayed when you enter successfully.
Fig 3.1-2
After you enter router as super user, you can check, config and modify all the options. You can use the
system diagnostic function also.
If you enter as common user, you can check the status of ROUTER, but can’t change the most of options.
10

Rate

4 / 5 based on 1 vote.

Popular Kozumi Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top