HooToo HT-ND006 Router Manual PDF (Setup & Configuration Guide)

Page 26 / 43 Scroll up to view Page 21 - 25

23

2.

WPA-Personal:

WPA personal, supports AES and TKIP cipher types.

3.

WPA2-Personal:

WPA2 personal, supports AES, TKIP, and TKIP+AES

cipher types.

4.

Mixed WPA/WPA2-PSK:

If selected, both WPA-PSK and WPA2-PSK

secured wireless clients can join your wireless network

.

WPA cipher type:

1.

AES:

If selected, wireless speed can reach up to 300Mbps.

2.

TKIP:

If selected, wireless speed can reach up to 54Mbps.

3.

TKIP+AES:

If selected, both AES and TKIP secured wireless clients can

join your wireless network.

Key Renewal Interval:

Enter a valid time period for the key to be

changed.

4.4.3

WPS Settings

Choose PIN or PBC for improved Wi-Fi protection.

Security Mode:

1.

Disable

:

If you want to allow all wireless clients to join your wireless

network.

Page 27 / 43

24

4.4.4

Access Control

The Wireless Access Control is based on the MAC address of the wireless

adapter to determine whether it communicates with the Router or not.

Select "Off" to disable this function.

Select "Allow" or "Block" to enable this function.

4.4.5

Connection Status

Here you can see a list of the wireless devices connected to the router.

MAC Address:

Shows the connecting PC's MAC address.

Bandwidth:

The width of the channel frequency.

Note:

The bandwidth refers to the channel bandwidth instead of the

wireless connection rate. This page informs you if there are unauthorized

connections to your wireless network by viewing the wireless client list.

Page 28 / 43

25

4.5.

LAN Settings

4.5.1.

LAN Settings

Here you can configure the LAN IP Address and Subnet Mask. This IP

address is used to access the device settings through a web browser.

Make sure to keep track of any changes you apply to this page.

Configuration Procedure:

1

．

Change the IP address to the one you wish to use, for example

10.10.10.252.

2

．

Click Save to save your settings.

Note

：

1.

Default IP address and subnet mask are, respectively, 10.10.10.252

and 255.255.255.0.

2.

Make sure to keep track of any changes you apply to this page. If

you change the Router LAN IP address, it is necessary to connect to

the new IP address and log in again. Also, you must set the default

gateway addresses of all LAN PCs to this new IP address.

3.

The router LAN IP address and WAN IP address cannot be on the

same IP segment. If they are then the router will not be able to

access the Internet.

Page 29 / 43

26

4.5.2.

DHCP Server

Here you can change the DHCP IP address pool and lease time.

DHCP Server Configuration:

1.

DHCP Server:

Enable/disable the DHCP server.

2.

Start IP/End IP:

Specify Start/End IP addresses of the IP address pool.

These addresses should be part of the same IP address subnet as the

router LAN IP address.

3.

Lease Time:

Time length for the IP address to be assigned to each

device before it is refreshed.

4.

Click

Save

to save your settings.

Note:

1.

By default, the router performs as a DHCP server. Do not disable the

DHCP server feature unless you want to manually configure TCP/IP

settings for all PCs on your LAN.

2.

Lease time will be renewed automatically upon expiration. No

additional configuration are needed.

3.

If you are not an advanced user, the default DHCP server settings

are recommended.

Page 30 / 43

27

4.5.3.

DHCP List & Binding

Here you can view the DHCP dynamic client list: host name, IP address,

MAC address, and lease time information.

Note:

1.

You can know whether there are unauthorized connections by

viewing the client list.

2.

You can specify a reserved IP address for a PC in the LAN. That PC

will always receive the same IP address each time it accesses the

DHCP server. Reserved IP addresses can be assigned to servers that

require permanent IP settings.

3.

If the IP address you have reserved for your PC is currently used by

another client, then you will not be able to obtain a new IP address

from the device DHCP server, instead, you will have to manually

specify a different IP address for your PC to access the Internet.

For PCs that have already obtained IP addresses, you may need to

perform the Repair action to activate the configured static IP addresses.

4.6

Expert Settings

4.6.1

URL Filter

This section is to set URL filtering access. Check the checkbox to enable

this function. Select one policy from the drop-down menu and enter a

policy name in the field. You can set the access restriction parameters

(e.g. the fixed IP range, times, and days).

Rate

Popular HooToo Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share