Hitron Technologies CVE-30360 Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

Hitron Technologies

CVE-30360

Page 31 / 98 Scroll up to view Page 26 - 30

HITRON CVE-30360 USER’S GUIDE

CABLE

FIGURE 6:

The Cable > System Info Screen

The following table describes the labels in this screen.

TABLE 7:

The Cable > System Info Screen

General Information

Vendor

Identification

This displays the name of the company that supplied the

CVE-30360.

Model Name

This displays the device’s model name (CVE-30360).

DOCSIS Mode

This displays the version of the Data Over Cable Service

Interface Specification (DOCSIS) standard to which the

CVE-30360 complies.

HW Version

This displays the version number of the CVE-30360’s

physical hardware.

SW Version

This displays the version number of the software that

controls the CVE-30360.

Boot ROM Version

This displays the version number of the program that

controls the CVE-30360’s boot procedure (in which the

main software is loaded).

MAC Address

RF MAC Address

This displays the Media Access Control (MAC) address of

the CVE-30360’s RF module. This is the module that

connects to the Internet through the

CATV

connection.

Ethernet MAC

Address

This displays the Media Access Control (MAC) address of

the CVE-30360’s Ethernet module. This is the module to

which you connect through the

LAN

ports.

WAN MAC Address

(in Routing Mode

This displays the Media Access Control (MAC) address of

the module that connects to the Internet through the

CATV

connection when the CVE-30360 is in routing mode.

Page 32 / 98

HITRON CVE-30360 USER’S GUIDE

CABLE

2.3

THE INITIALIZATION SCREEN

This screen displays the steps successfully taken to connect to the Internet over the

CATV

connection.

Use this screen for troubleshooting purposes to ensure that the CVE-30360 has

successfully connected to the Internet; if an error has occurred you can identify the

stage at which the failure occurred.

NOTE:

This screen displays when you first log in to the CVE-30360.

Click

Cable

Initialization

. The following screen displays.

Primary BSSID

MAC Address

This displays the Media Access Control (MAC) address of

the CVE-30360’s Basic Service Set IDentifier (BSSID).

This is the MAC address of the wireless module to which

wireless clients connect.

NOTE:

You may have additional BSSIDs, depending on

your contract with your service provider.

System Time

This displays the current date and time.

System Uptime

This displays the number of days, hours, minutes and

seconds since the CVE-30360 was last switched on or

rebooted.

Network Access

This field displays when you are connected to your service

provider, and shows whether or not your service provider

allows you to access the Internet over the

CATV

connection.



Permitted

displays if you can access the Internet.



Denied

displays if you cannot access the Internet.

TABLE 7:

The Cable > System Info Screen (continued)

Page 33 / 98

HITRON CVE-30360 USER’S GUIDE

CABLE

FIGURE 7:

The Cable > Initialization Screen

For each step:



Process

displays when the CVE-30360 is attempting to complete a connection

step.



Success

displays when the CVE-30360 has completed a connection step.

2.4

THE STATUS SCREEN

Use this screen to discover information about:



The nature of the upstream and downstream connection between the CVE-

30360 and the device to which it is connected through the

CATV

interface.



IP details of the CVE-30360’s WAN connection.

You can also configure the CVE-30360’s downstream center frequency.

Click

Cable

Status

. The following screen displays.

Page 34 / 98

HITRON CVE-30360 USER’S GUIDE

CABLE

FIGURE 8:

The Cable > Status Screen

The following table describes the labels in this screen.

TABLE 8:

The Cable > Status Screen

Network Access

This displays whether or not your service provider allows

you to access the Internet over the

CATV

connection.



Permitted

displays if you can access the Internet.



Denied

displays if you cannot access the Internet.

Downstream

NOTE:

The downstream signal is the signal transmitted to the CVE-30360.

Page 35 / 98

HITRON CVE-30360 USER’S GUIDE

CABLE

Frequency to Tune to

This displays the current center frequency in Hertz (Hz)

over which data is transmitted to the CVE-30360 over

the

CATV

interface. This is the frequency to which the

CVE-30360 is locked in; it will only scan for another

frequency if this frequency becomes unavailable.

If you want the CVE-30360 to attempt to connect at a

different frequency, enter it in the field and click

Apply

NOTE:

Do not change the frequency unless you have a

good reason to do so.

Scanning Start

Frequency

This displays the frequency in Hertz (Hz) at which the

CVE-30360 begins scanning for a connection over the

CATV

interface (if a frequency is not already locked in).

Channel Frequency

This displays the actual frequency of each downstream

data channel to which the CVE-30360 is connected.

Modulation

This displays the type of modulation that each

downstream channel uses. Possible modulation types

Signal Strength

This displays the power of the signal of each

downstream data channel to which the CVE-30360 is

connected, in dBmV (decibels above/below 1 millivolt).

Signal Noise Ratio

This displays the Signal to Noise Ratio (SNR) of each

downstream data channel to which the CVE-30360 is

connected, in dB (decibels).

Upstream

NOTE:

The upstream signal is the signal transmitted from the CVE-30360.

Channel ID

This displays the ID number of each channel on which

the upstream signal is transmitted.

Upstream Frequency

This displays the frequency in Herz (Hz) of each

upstream data channel to which the CVE-30360 is

connected.

Upstream Bandwidth

This displays the bandwidth of each upstream data

channel to which the CVE-30360 is connected (in Hertz).

SCDMA Mode

This displays the Synchronous Code Division Multiple

Access (SCDMA) mode of each channel on which the

upstream signal is transmitted.

Transmission Signal

Strength

This displays the transmitted power of the signal of each

upstream data channel to which the CVE-30360 is

connected, in dBmV (decibels above/below 1 millivolt).

Cable Modem IP Information

IP Address

This displays the CVE-30360’s WAN IP address. This IP

address is automatically assigned to the CVE-30360

Subnet Mask

This displays the CVE-30360’s WAN subnet mask.

TABLE 8:

The Cable > Status Screen (continued)

Rate

Popular Hitron Technologies Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share