1. Home
    2. /
  2. Manuals
    3. /
  3. FRITZ
    4. /
  4. WLAN-7390
    5. /
  5. 25
Page 121 / 197 Scroll up to view Page 116 - 120
Removing the Printer Port in Windows XP
121
3.
Click the “Uninstall/Change” button.
4.
Confirm the next query by clicking “Continue”.
This concludes the uninstallation of the printer port.
Removing the Printer Port in Windows XP
1.
Open “start / Control Panel / Add or Remove Pro-
grams”. Make sure that the “Change or Remove Pro-
grams” button is selected in the column at left.
2.
Select the “AVM FRITZ!Box USB Printer Port“ entry
from the list of “Currently installed programs”.
3.
Click the “Change/Remove” button.
This concludes the uninstallation of the printer port.
This concludes the uninstallation of the program group.
Page 122 / 197
122
Product Details
II
PRODUCT DETAILS AND USEFUL INFORMATION
1
Product Details
FRITZ!Box Fon WLAN 7390
This chapter provides you with product details on FRITZ!Box Fon
WLAN 7390. You receive information on cables and adapters, technical
data and further details.
1.1
Cable
See the information in the following section on the individu-
al cables and adapters on the FRITZ!Box Fon WLAN 7390.
DSL/Telephone Cable
The DSL/telephone cable is a special combined cable devel-
oped by AVM to connect the FRITZ!Box Fon WLAN 7390 to
the DSL splitter and the ISDN NT or analog telephone line.
If you need a longer cable, you can extend one or multiple
ends of the combined cable using RJ45 double couplings.
Which ends of the cable you extend depends on the spa-
tial conditions at your location.
You will need the following components to extend the
length of one or more ends of your DSL/telephone cable:
•
1 standard network cable
•
1 standard RJ45 CAT5 double coupling
Both components are available from specialized vendors.
AVM recommends that the standard DSL/telephone cable
be extended to no more than 10 meters.
Your FRITZ!Box Fon WLAN 7390 package may include only
the DSL cable (see page 122). For a description of the ex-
act contents of your FRITZ!Box package, see the card-
board box in which the FRITZ!Box was delivered.
Page 123 / 197
Network Cable
123
Network Cable
The FRITZ!Box Fon WLAN 7390 network cable (yellow) is a
standard category 5 (Cat5) Ethernet cable. If you need a
replacement cable, a longer cable or an extension, please
use a standard STP-type (Shielded Twisted Pair) Ethernet
cable of category 5 or 5e (Cat5 or Cat5e). To extend the ca-
ble you will need a shielded RJ45 double coupling (Cat5 or
Cat5e) with a 1:1 pin assignment. You can use both
straight cables and crosslink cables. All components are
available from specialized vendors.
When components of a smaller category are used, re-
duced transmission rates may result.
AVM recommends using a network cable no more than
100 meters long.
1.2
LEDs
Five LEDs are built into the top of the FRITZ!Box Fon
WLAN 7390, which flash or light up to display various con-
nection statuses.
Remember that the quality of the line may be decrease as
the distance from the central switching station increases.
Additional network cable is required if you would like to
use all of the FRITZ!Box Fon WLAN 7390 network ports.
Page 124 / 197
124
LEDs
LED
Condition
Meaning
Power/DSL
on
•
FRITZ!Box on standby
•
the device has electrical power and the DSL line is
ready for operation
flashing
•
the device has electrical power
•
the connection to DSL is being established or has
been interrupted
Internet
on
a telephone connection to the Internet is active
flashing
there are messages in your mailbox (this function must be
supported by your telephony carrier)
Fixed Line
on
a telephone connection via the telephone line (ISDN/ana-
log) is active
flashing
there are messages in your mailbox (this function must be
supported by your telephony carrier)
WLAN
on
WLAN function is enabled.
flashing
•
enabling or disabling WLAN function
•
adopting the WLAN settings
•
performing WPS
•
WPS procedure aborted: More than two WLAN devices
are performing WPS at the same time. Repeat the con-
nection routine.
Info
on
•
a telephone connection between two Internet telepho-
ny subscribers is active; the call is free of charge (this
function must be supported by your Internet telepho-
ny provider)
•
signals an event specified by the user
•
Stick & Surf procedure concluded
flashing
•
updating the firmware
•
specified value for online meter reached
•
signals an event specified by the user
•
Stick & Surf procedure in progress
flashes red
Error: Open the FRITZ!Box user interface and follow the in-
structions on the “Overview” page
Page 125 / 197
WLAN Button
125
“Info” LED
Here you can define what additional information should
be displayed on the “Info” LED. For details, see the “ Sys-
tem / “Info” Display” section of the user interface of your
FRITZ!Box.
1.3
WLAN Button
The FRITZ!Box is equipped with a WLAN button.
The button has two functions:
•
enabling/disabling WLAN
•
establishing a WLAN Connection with the WPS meth-
od (see “WPS (Wi-Fi Protected Setup)” from
page 148)
If you hold the button down longer than six seconds,
this function will be executed. For this to work, your
WLAN adapter must support the WPS method.

Rate

4.5 / 5 based on 2 votes.

Popular FRITZ Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top