1. Home
    2. /
  2. Manuals
    3. /
  3. eHome
    4. /
  4. EH100
    5. /
  5. 6
Page 26 / 92 Scroll up to view Page 21 - 25
±µ
eHome EH100 User Manual
Section ² - Configuration
Dynamic IP
Address:
Host Name:
MAC Address:
Internet Connection Setup
Dynamic IP (Cable)
Clone MAC
Address:
DNS Addresses:
MTU:
Choose Dynamic IP Address to obtain IP
Address information automatically from
your ISP. Select this option if your ISP
does not give you an IP address to use.
This option is commonly used for Cable
modem services.
The Host Name is optional but may be
required by some ISPs. The default host
name is the device name of the Router
and may be changed.
The default MAC Address is set to the
WAN’s physical interface MAC address
on the Broadband Router. It is not
recommended that you change the
default MAC address unless required
by your ISP.
You can use the
Clone MAC Address
button to copy the MAC address of your network adapter and replace the WAN MAC
address with it. Some ISP’s record the MAC address of the network adapter in the computer used to initially connect to
their service. The ISP will then only grant Internet access to requests from a computer with this particular Mac Address.
Enter the Primary DNS server IP address assigned by your ISP.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1500 is the
default MTU.
Page 27 / 92
±¶
eHome EH100 User Manual
Section ² - Configuration
Internet Connection Setup
PPPoE (DSL)
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide
you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE
software from your computer. The software is no longer needed and will not work through a router.
Select
Dynamic
(most common) or
Static
. Select
Static
if your ISP assigned
you the IP address, subnet mask,
gateway, and DNS server addresses.
PPPoE:
User Name:
Enter your PPPoE user name.
Password:
Enter your PPPoE password and then
retype the password in the next box.
Service Name:
Enter the ISP Service Name (optional).
IP Address:
Enter the IP address (Static PPPoE
only).
DNS Addresses:
Enter the Primary and Secondary DNS
Server Addresses (Static PPPoE only).
Maximum Idle
Time:
Enter a maximum idle time during which
the Internet connection is maintained
during inactivity. To disable this
feature, enable Auto-reconnect.
MTU:
Maximum Transmission Unit - you may
need to change the MTU for optimal
performance with your specific ISP. 1492
is the default MTU.
Connection Mode
Select:
Select either Always-on, Manual, or
Connect-on demand.
Page 28 / 92
±·
eHome EH100 User Manual
Section ² - Configuration
Internet Connection Setup
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with
a username and password. This option is used for some DSL services.
PPTP:
Select
Dynamic
(most common) or
Static
. Select
Static
if your ISP assigned
you the IP address, subnet mask,
gateway, and DNS server addresses.
IP Address:
Enter the IP address (Static PPTP
only).
Subnet Mask:
Enter the Primary and Secondary DNS
Server Addresses (Static PPTP only).
Gateway:
Enter the Gateway IP Address provided
by your ISP.
Server IP:
Enter the Server IP provided by your ISP
(optional).
PPTP Account:
Enter your PPTP account name.
Maximum Idle
Time:
Enter a maximum idle time during which
the Internet connection is maintained
during inactivity. To disable this feature,
enable Auto-reconnect.
MTU:
Maximum Transmission Unit - you may
need to change the MTU for optimal
performance with your specific ISP. 1492
is the default MTU.
Connect Mode:
Select either Always-on, Manual, or
Connect-on demand.
Page 29 / 92
±¸
eHome EH100 User Manual
Section ² - Configuration
Internet Connection Setup
L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username
and password. This option is typically used for DSL services.
L2TP:
Select
Dynamic
(most common) or
Static
. Select
Static
if your ISP assigned
you the IP address, subnet mask,
gateway, and DNS server addresses.
IP Address:
Enter the IP address (Static L2TP
only).
Subnet Mask:
Enter the Primary and Secondary DNS
Server Addresses (Static L2TP only).
Gateway:
Enter the Gateway IP Address provided
by your ISP.
DNS:
The DNS server information will be
supplied by your ISP (Internet Service
Provider.)
Server IP:
Enter the Server IP provided by your ISP
(optional).
L2TP Account:
Enter your L2TP account name.
L2TP Password:
Enter your L2TP password and then
retype the password in the next box.
Maximum Idle
Time:
Enter a maximum idle time during which
the Internet connection is maintained
during inactivity. To disable this feature,
enable Auto-reconnect.
Page 30 / 92
²0
eHome EH100 User Manual
Section ² - Configuration
MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the
default MTU.
Connect Mode:
Select either Always-on, Manual, or Connect-on demand.

Rate

4.5 / 5 based on 2 votes.

Popular eHome Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top