Page 11 / 92 Scroll up to view Page 6 - 10
11
eHome EH100 User Manual
Section ± - Installation
If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:
1. Place the router in an open and central location. Do not plug the power adapter into the router.
2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down
your computer.
3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the
WAN port on the router.
4. Plug an Ethernet cable into one of the four LAN ports on the router. Plug the other end into the Ethernet port on your
computer.
5. Turn on or plug in your modem.
Wait for the modem to boot (about 30 seconds).
6. Plug the power adapter to the router and connect to an outlet or power strip. Wait about 30 seconds for the router
to boot.
7. Turn on your computer.
8. Verify the link lights on the router. The power light, WAN light, and the LAN light (the port that your computer is
plugged into) should be lit. If not, make sure your computer, modem, and router are powered on and verify the cable
connections are correct.
9. Skip to page 14 to configure your router.
Connect to Cable/DSL/Satellite Modem
Page 12 / 92
eHome EH100 User Manual
Section ± - Installation
If you are connecting the
eHome
router to another router to use as a wireless access point and/or switch, you will have
to do the following before connecting the router to your network:
• Disable UPnP
• Disable DHCP
• Change the LAN IP address to an available address on your network. The LAN ports on the router cannot
accept a DHCP address from your other router.
To connect to another router, please follow the steps below:
1. Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable.
Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the
Networking Basics
section for more information. If you need to change the settings, write down your existing settings
before making any changes. In most cases, your computer should be set to receive an IP address automatically in
which case you will not have to do anything to your computer.
2. Open a web browser and enter
and press
Enter
. When the login window appears, set the user
name to
admin
and leave the password box empty. Click
OK
to continue.
3. Browse to the
Advanced > Advanced Network
page. Uncheck the box next to
Enable UPnP
. Click the
Save
Settings
button to continue.
4. Browse to the
Setup > Network Settings
page.
Uncheck the box next to
Enable DHCP Server
.
5. Under
Router Settings
, enter an available IP address and the subnet mask of your network. Click
Save Settings
to save your settings. Use this new IP address to access the configuration utility of the router in the future. Close the
browser and change your computer’s IP settings back to the original values as in Step 1.
Connect to Another Router
Page 13 / 92
eHome EH100 User Manual
Section ± - Installation
6. Disconnect the Ethernet cable from the router and reconnect your computer to your network.
7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug
anything into the WAN port of the
eHome
router.
8. You may now use the other 3 LAN ports to connect other Ethernet devices and computers. To configure your wireless
network, open a web browser and enter the IP address you assigned to the router. Refer to the
Configuration
and
Wireless
Security
sections for more information on setting up your wireless network.
Page 14 / 92
eHome EH100 User Manual
Section ² - Configuration
Configuration
This section will show you how to configure your new eHome wireless router using the web-based configuration
utility.
Web-based Configuration Utility
To access the configuration utility, open a web-browser
such as Internet Explorer and enter the IP address of
the router (192.168.0.1).
Enter the user name (admin) and your password. Leave
the password blank by default.
If you get a “Page Cannot be Displayed” error, please
refer to the
Troubleshooting
section for assistance.
Page 15 / 92
eHome EH100 User Manual
Section ² - Configuration
After logging in the Setup page will be displayed:

Rate

4.5 / 5 based on 2 votes.

Popular eHome Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top