Page 111 / 190 Scroll up to view Page 106 - 110
3
2
1
6 Universal Repeater
In this mode, this broadband router acts as a wireless repeater. It will repeat the signal of
the wireless access point you specified, to extend its wireless coverage. The broadband
router will still accept wireless clients when in this mode.
Here are descriptions of every setup item:
Item Name
Description
Band
Please select the radio band from one of
following options (must be the same with the
wireless access point you wish to connect):
2.4 GHz (B): 2.4GHz band, only allows 802.11b
wireless network client to connect this router
(maximum transfer rate 11Mbps).
2.4 GHz (N): 2.4GHz band, only allows 802.11n
wireless network client to connect this router
Page 112 / 190
(maximum transfer rate 300Mbps).
2.4 GHz (B+G):
2.4GHz band, only allows
802.11b and 802.11g wireless network client
to connect this router (maximum transfer rate
11Mbps for 802.11b clients, and maximum
54Mbps for 802.11g clients).
2.4 GHz (G): 2.4GHz band, only allows 802.11g
wireless network client to connect this router
(maximum transfer rate 11Mbps).
2.4 GHz (B+G+N): 2.4GHz Band, Allows
802.11b, 802.11g, and 802.11N wireless
clients. It’s recommends to select this band to
maximize compatibility.
ESSID
This is the name of broadband router. You can
type any alphanumerical characters here,
maximum 32 characters. ESSID is used to
identify your own broadband router from
others when there are other broadband
routers in the same area. Default SSID is
‘default’, it’s recommended to change default
ESSID value to the one which is meaningful to
you, like myhome, office_room1, etc.
Channel Number
Select the channel number you wish to use; all
access points must use the same channel.
Associated Clients
Click ‘Show Active Clients’ button to show
the list of all connected wireless clients. You
can click ‘Refresh’ in new window to get
latest list again, or click ‘Close’ to close the
Page 113 / 190
window.
Please note that if you have pop
up blocker
installed, you may have to disable it or tell
your pop
up blocker to allow the popup
window, or you will not be able to see the
wireless client list window.
Root AP SSID
Please input the SSID of the wireless access
point you wish to extend signal coverage.
Site Survey
Click ‘Select Site Survey’ and a popup window
will appear. All reachable wireless access
points will be shown in the window. Select the
wireless access point you wish to connect from
the list, and click ‘Done’. If the wireless access
point you wish to connect is not listed, you can
click ‘Refresh’ to rescan.
If you still can’t find the wireless access point
you wish to connect, please move the
broadband router to the place nearer to the
access point you wish to connect.
When you finished with the settings in this page, you can click ‘Apply’ button to save
changes you made in this page, or you can click ‘Cancel’ to discard changes. After you click
‘Apply’ button, you’ll see the following message:
Please click ‘Apply’ to save changes you made and restart the broadband router, this
requires about 30 seconds and the broadband router will stop responding (this is normal
Page 114 / 190
and is not malfunction). You can reconnect to this broadband router and continue on other
settings later.
You can click ‘Continue’ to continue on other settings without restart the broadband router,
however, the changes you made will not take effect before you restart the broadband
router.
Page 115 / 190
3
2
2 Security Settings
In certain AP working modes, you can enable encryption to improve security level.
When you click ‘Set Security’ button, the following window will appear:
Please select an encryption method from ‘Encryption’ dropdown menu, and corresponding
setting will appear:
Disabled
Encryption is disabled. It’s
not recommended
to disable encryption because other people
may use certain wireless scanner to copy the data transferred over air.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top