1. Home
    2. /
  2. Manuals
    3. /
  3. EDIMAX
    4. /
  4. BR-6214K
    5. /
  5. 5
Page 21 / 45 Scroll up to view Page 16 - 20
20
Parameters
Description
Account
Enter your account name to login to your Broadband router.
Password
Enter your password
Retype your
Enter your password again for verification purposes
Password
Note
: If you forget your password, you’ll have to reset the router to the factory default
(password is 1234) with the reset button (see router’s back panel)
Click <
Apply>
at the bottom of the screen to save the above configurations. You can now configure other advance
sections or start using the router (with the advance settings in place)
2.1.3 Remote Management
The remote management function allows you to designate a host range in the Internet the ability to configure the
Broadband router from a remote site. Enter the designated host IP Addresses in the IP Address field.
Parameters
Description
IP Address
Please specify the IP range to the Remote Management IP fields. All the Internet IPs
that inside this range can manage this router from WAN side.
Port
To avoid conflict of virtual server at port 80, user can specify a different port in Remote
Management Port for WAN side access.
Ping from WAN side
Ping from WAN side is turned on by default and could be turned off if the Enable
checkbox is unchecked.
Click <
Apply>
at the bottom of the screen to save the above configurations. You can now configure other advance
sections or start using the router (with the advance settings in place)
Downloaded from
www.Manualslib.com
manuals search engine
Page 22 / 45
21
2.2 WAN
Use the WAN Settings screen if you have already configured the Quick Setup Wizard section and you would like to
change your Internet connection type. The WAN Settings screen allows to specify the type of WAN port connect you
want to establish with your ISP. The WAN settings offer the following selections for the router’s WAN port,
Static IP,
DHCP
,
PPPoE
,
PPTP
,
L2TP
, and
DDNS
.
Parameters
Description
2.2.1 Static IP
Your ISP has given you an IP address already
2.2.2 DHCP
Your ISP will automatically give you an IP address
2.2.3 PPPoE
Your ISP requires PPPoE connection.
2.2.4 PPTP
Your ISP requires you to use a Point-to-Point Tunneling Protocol (PPTP) connection.
2.2.5 L2TP
Your ISP requires L2TP connection.
2.2.6 DDNS
You can specify a DDNS server that you wish to use and configure the user name
and password provided by you DDNS service provider.
Once you have made a selection, click <
More Configuration>
at the bottom of the screen and proceed to the manual’s
relevant sub-section
2.2.1 Static IP
Select Static IP address if your ISP has given you a specific IP address for you to use. Your ISP should provide all the
information required in this section. (See chapter 1 “Static IP Address” for more detail)
2.2.2 DHCP
Choose the DHCP selection if your ISP will automatically give you an IP address. Some ISP’s may also require that you
fill in additional information such as MAC address (see chapter 1 “Dynamic IP” for more detail)
2.2.3 PPPoE (PPP over Ethernet)
Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. Your ISP should provide all the
information required in this section. (See chapter 1 “PPPoE” for more detail)
2.2.4 PPTP
Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. Your ISP should provide all the
information required in this section. (See chapter 1 “PPTP” for more detail)
2.2.5 L2TP
Select L2TP if your ISP requires the L2TP protocol to connect you to the Internet. Your ISP should provide all the
information required in this section. (See chapter 1 “L2TP” for more detail)
2.2.6 DDNS
DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your
static domain name from the DDNS service providers. This router supports DynDNS, TZO and other common DDNS
service providers.
Downloaded from
www.Manualslib.com
manuals search engine
Page 23 / 45
22
Parameters
Description
Service Type
Select a DDNS service provider or select Disabled to disable DDNS function.
Username
The account that your DDNS service provider assigned to you
Password
The password you set for the DDNS service account above
Host Name
Your static domain name that use DDNS
Click <
Apply>
at the bottom of the screen to save the above configurations. You can now configure other advance
sections or start using the router (with the advance settings in place)
2.3 LAN
The LAN Port screen below allows you to specify a private IP address for your router’s LAN ports as well as a subnet
mask for your LAN segment.
Downloaded from
www.Manualslib.com
manuals search engine
Page 24 / 45
23
Parameters
Description
IP address
This is the router’s LAN port IP address (Your LAN clients default gateway IP
address)
IP Subnet Mask
Specify a Subnet Mask for your LAN segment
DHCP Server Status
You can enable or disable the DHCP server. By enabling the DHCP server the router
will automatically give your LAN clients an IP address. If the DHCP is not enabled
then you’ll have to manually set your LAN client’s IP addresses; make sure the LAN
Client is in the same subnet as this broadband router if you want the router to be
your LAN client’s default gateway
IP Address Pool
You can select a particular IP address range for your DHCP server to issue IP
addresses to your LAN Clients.
WINS Server
You can specify the WINS server to assign to DHCP clients.
Provide Real DNS Server
When check this box, DHCP server will provide WAN DNS server to DHCP clients.
Otherwise, DHCP server will provide itself as the DNS server.
Domain from upper DHCP
Enable this to assign the domain name from WAN connection.
Static DHCP leases
Static DHCP leases is for user to statically associate an IP address to a specific
MAC address.
Dynamic DHCP Client List
Dynamic DHCP Client List shows all IP addresses already assigned and the
corresponding LAN PC hostname and their MAC addresses.
Click <
Apply>
at the bottom of the screen to save the above configurations. You can now configure other advance
sections or start using the router (with the advance settings in place)
2.4 QoS
This router supports various types of QoS – Port-based QoS, Rate Policing QoS, and Guaranteed/Spare Class QoS.
For Port based QoS, user can specify the High/Low queue priority for each Ethernet port and can apply total rate limit to
any port from 128Kbps to 32Mbps or at Full-rate(100Mbps). Flow control can also be enabled/disabled on per-port basis.
For Application based QoS, user can specify a destination port number and associate it with an egress priority (High or
Low). For example, in Fig 35, if user config port 7297 with high priority, then user would experience better service quality
for such flows.
Parameters
Description
2.4.1 Port-based QoS
User can differentiate packet priority by L4 port number or by physical Ethernet port
number.
2.4.2 Rate Policing QoS
User can specify a L3/4 criterion and associate it with a maximum token (packet
rate or data rate based).
2.4.3 Guaranteed/Spare Class
Your ISP requires PPPoE connection.
QoS
Downloaded from
www.Manualslib.com
manuals search engine
Page 25 / 45
24
2.4.1 Port-based QoS
For Application based QoS, user can specify a destination port number and associate it with an egress priority (High or
Low). For example, if user configures port 7297 with high priority, then user would experience better service quality for
such flows.
For Port based QoS, user can specify the High/Low queue priority for each Ethernet port and can apply total rate limit to
any port from 128Kbps to 32Mbps or at Full-rate(100Mbps). Flow control can also be enabled/disabled on per-port basis.
Parameters
Description
Enable QoS by Application
Enable application-based QoS.
Protocol/Specific Port#
Set the priority of the specified protocol name or port number to higher or lower
priority.
Enable QoS by device port
Enable Port-based QoS.
Click <
Apply>
at the bottom of the screen to save the above configurations. You can now configure other advance
sections or start using the router (with the advance settings in place)
2.4.2 Rate Policing QoS
This router supports Rate Policing QoS. User can specify a L3/4 criterion and associate it with a maximum token (packet
rate or data rate based). If a packet arrives and it matches to a rate policing entry, router decreases entry’s allocated
token by one (if pps based) or by packet length in bytes(if bps based). If unfortunately the packet just run out of allocated
tokens, then it would be dropped directly or logged to software, depends on the setting of Drop Log field.
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4.5 / 5 based on 2 votes.

Popular EDIMAX Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top