1. Home
    2. /
  2. Manuals
    3. /
  3. EDIMAX
    4. /
  4. AR-7266WnA
    5. /
  5. 16
Page 76 / 124 Scroll up to view Page 71 - 75
67
Parameter
Description
Disable WPS
Check to disable the Wi-Fi protected Setup.
WPS Status
When AP’s settings are factory default (out of box), it is
set to open security and un-configured state. “WPS
Status” will display it as “UnConfigured”. If it already
shows “Configured”, some registrars such as Vista WCN
will not configure AP. Users will need to go to the
“Backup/Restore” page and click “Reset” to reload
factory default settings.
Self-PIN Number
“Self-PIN Number” is AP’s PIN. Whenever users want to
change AP’s PIN, they could click “Regenerate PIN” and
then click “ Apply Changes”. Moreover, if users want to
make their own PIN, they could enter four-digit PIN
without checksum and then click “ Apply Changes”.
However, this would not be recommended since the
Page 77 / 124
68
registrar side needs to be supported with four-digit PIN.
Regenerate PIN
Click to regenerate the Self-PIN Number.
Push Button
Configuration
Clicking this button will invoke the PBC method of WPS.
It is only used when AP acts as a registrar.
Start PBC
Click to start the Push Button method of WPS.
Reset
It restores the original values.
Client PIN Number
It is only used when users want their station to join AP’s
network. The length of PIN is limited to four or eight
numeric digits. If users enter eight-digit PIN with
checksum error, there will be a warning message
popping up. If users insist on this PIN, AP will take it.
When you finish, click ‘Apply Changes’. You’ll see the following message
displayed on web browser:
Press ‘Continue’ to save the settings made and back to web management
interface; press ‘Apply’ to save the settings made and restart the router so the
settings will take effect after it reboots.
5.2.5.
QoS
The router supports IP QoS feature that can provide different priority to different
users or data flows.
Page 78 / 124
69
Parameter
Description
IP QoS
Click the radio button to enable or disable the IP QoS
function.
Default QoS
Select the default mode of QoS from the list.
IP Precedence:
In QoS, a three-bit field in the ToS byte of the IP header
(see RFC 791). Using IP Precedence, a network
administrator can assign values from 0(the default) to 7
Page 79 / 124
70
to classify and prioritize types of traffic.
802.1P:
IEEE 802.1p is a 3 bit field within an Ethernet frame
header when using tagged frames on an 802.1 network.
It specifies a priority value of between 0 and 7 inclusive
that can be used by Quality of Service (QoS) disciplines
to differentiate traffic.
Source IP
The IP address of the traffic source.
Source Netmask
The source IP netmask. This field is required if the
source IP has been entered.
Source Port
The source port of the selected protocol. You cannot
configure this field without entering the protocol first.
Destination IP
The IP address of the traffic destination.
Destination Netmask
The destination IP netmask. This field is required if the
destination IP has been entered.
Destination Port
The destination port of the selected protocol. You cannot
configure this field without entering the protocol first.
Protocol
The selections are TCP, UDP, ICMP and the blank for
none. This field is required if the source port or
destination port has been entered.
Physical Port
The incoming ports. The selections include LAN ports,
wireless port, and the blank for not applicable.
Outbound Priority
The priority level for the traffic that matches this
classification rule. The possible selections are (in the
descending priority): p0, p1, p2, p3.
Page 80 / 124
71
802.1p
Select this field to mark the 3-bit user-priority field in the
802.1p header of the packet that matches this
classification rule. Note that this 802.1p marking is
workable on a given PVC channel only if the VLAN tag is
enabled in this PVC channel.
Precedence
Select this field to mark the IP precedence bits in the
packet that match this classification rule.
TOS
The IP (Internet Protocol) uses the ToS (Type of Service)
field to provide an indication of the quality of service
desired. These parameters are to be used to guide the
selection of the actual service parameters when
transmitting an IP datagram through a particular
network.0
IP QoS Rules
This table lists the rules you have configured. Click
“Delete Selected” to delete the selected rules or click
“Delete All” to delete all the rules.
When you finish, click ‘Apply Changes’. You’ll see the following message
displayed on web browser:
Press ‘Continue’ to save the settings made and back to web management
interface; press ‘Apply’ to save the settings made and restart the router so the
settings will take effect after it reboots.

Rate

3.5 / 5 based on 2 votes.

Popular EDIMAX Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top