Page 181 / 298 Scroll up to view Page 176 - 180
igor2930 Series User’s Guide
173
Page 182 / 298
Vigor2930 Series User’s Guide
174
Index
Click this link to access into next page for setting SIP account.
Profile
Display the profile name of the account.
Domain/Realm
Display the domain name or IP address of the SIP registrar
server.
Proxy
Display the domain name or IP address of the SIP proxy
server.
Account Name
Display the account name of SIP address before @.
Ring Port
Specify which port will ring when receiving a phone call. Set
Phone1, Phone2, ISDN1-S0 or ISDN-TE as the default ring
port for the SIP account. If you choose Phone1, Phone2 or
ISDN1-S0, the ISDN2-TE selection will be dimmed, vice
versa. There are ten internal lines with numbers (30 – 39)
offered for
ISDN-S0
.
You can specify any one of them as ring
port for specified SIP account. By the way, ISDN-S0 can be
used by mapping with MSN numbers.
STUN Server
Type in the IP address or domain of the STUN server.
External IP
Type in the gateway IP address.
SIP PING interval
The default value is 150 (sec). It is useful for a Nortel server
NAT Traversal Support.
Status
Show the status for the corresponding SIP account.
R
means
such account is registered on SIP server successfully.
means
the account is failed to register on SIP server.
Profile Name
Assign a name for this profile for identifying. You can type
similar name with the domain. For example, if the domain
name is
draytel.org
, then you might set
draytel-1
in this field.
Page 183 / 298
igor2930 Series User’s Guide
175
Register via
If you want to make VoIP call without register personal
information, please choose
None
and check the box to achieve
the goal.
Some SIP server allows user to use VoIP function
without registering. For such server, please check the box of
Call without registration
. Choosing
Auto
is recommended.
The system will select a proper way for your VoIP call.
SIP Port
Set the port number for sending/receiving SIP message for
building a session. The default value is
5060.
Your peer must
set the same value in his/her Registrar.
Domain/Realm
Set the domain name or IP address of the SIP Registrar server.
Proxy
Set domain name or IP address of SIP proxy server. By the
time you can type
:port
number
after the domain name to
specify that port as the destination of data transmission (e.g.,
nat.draytel.org:5065
)
Act as Outbound Proxy
Check this box to make the proxy acting as outbound proxy.
Display Name
The caller-ID that you want to be displayed on your friend’s
screen.
Account Number/Name
Enter your account name of SIP Address, e.g. every text
before @.
Authentication ID
Check the box to invoke this function and enter the name or
number used for SIP Authorization with SIP Registrar. If this
setting value is the same as Account Name, it is not necessary
for you to check the box and set any value in this field.
Password
The password provided to you when you registered with a SIP
service.
Expiry Time
The time duration that your SIP Registrar server keeps your
registration record. Before the time expires, the router will
send another register request to SIP Registrar again.
NAT Traversal Support
If the router (e.g.
,
broadband router) you use connects to
internet by other device, you have to set this function for your
necessity.
None –
Disable this function.
Stun
– Choose this option if there is Stun server provided for
your router.
Manual
– Choose this option if you want to specify an
external IP address as the NAT transversal support.
Nortel
– If the soft-switch that you use supports Nortel
solution, you can choose this option.
Page 184 / 298
Vigor2930 Series User’s Guide
176
Ring Port
Set Phone1, Phone2, ISDN1-S0 or ISDN-TE as the default
ring port for this SIP account. If you choose Phone1, Phone2
or ISDN1-S0, the ISDN2-TE selection will be dimmed, vice
versa. There are ten internal lines with numbers (30 – 39)
offered for
ISDN-S0
.
You can specify one of them or choose
Any
as ring port for specified SIP account. By the way,
ISDN-S0 can be used by mapping with MSN numbers.
Ring Pattern
Choose a ring tone type for the VoIP phone call.
3.11.3 Phone Settings
This page allows user to set phone settings for Phone1, Phone2, ISDN1-S0 and
ISDN2-TE/S0 respectively.
Phone List
Port –
There are four phone ports provided here for you to
configure. Three (Index 1 to 3) are fixed and one (Index 4) is
configurable.
Phone1
and
Phone2
allow you to set general
settings for PSTN phones.
ISDN1-S0
and
ISDN2-TE
allow
you to set common settings for ISDN network connection.
ISDN2 port is configurable. Please use the drop down list to
choose
ISDN2-TE
for Internet connection or choose
ISDN2-S0
(ISDN intern) for ISDN phone. In addition, you
can connect six phones to this router in certain case. Please
refer to
Section 4-1
for detailed information of ISDN
phone/network connection.
Page 185 / 298
igor2930 Series User’s Guide
177
If you want to enable function of ISDN On-Net/Off-Net, you
have to choose ISDN2-TE.
Call Feature
– A brief description for call feature will be
shown in this field for your reference.
Codec
– The default Codec setting for each port will be
shown in this field for your reference. You can click the
number below the Index field to change it for each phone port.
Tone
- Display the tone settings that configured in the
advanced settings page of Phone Index.
Gain
- Display the volume gain settings for Mic/Speaker that
configured in the advanced settings page of Phone Index.
Default SIP Account
– “draytel_1” is the default SIP account.
You can click the number below the Index field to change SIP
account for each phone port.
DTMF Relay
– Display DTMF mode that configured in the
advanced settings page of Phone Index.
RTP
Symmetric RTP
– Check this box to invoke the function. To
make the data transmission going through on both ends of
local router and remote router not misleading due to IP lost
(for example, sending data from the public IP of remote router
to the private IP of local router), you can check this box to
solve this problem.
Dynamic RTP Port Start
- Specifies the start port for RTP
stream. The default value is 10050.
Dynamic RTP Port End
- Specifies the end port for RTP
stream. The default value is 15000.
RTP TOS
– It decides the level of VoIP package. Use the
drop down list to choose any one of them.
VoIP Collection Timer
– Keep the default setting.
VoIP Collection Timer Length
- Keep the default setting.
Detailed Settings for Phone1/Phone2 Port
Click the number link of each port, you can access into the following page for configuring
Phone settings. Below is the sample page for Phone1.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top