1. Home
    2. /
  2. Manuals
    3. /
  3. DrayTek
    4. /
  4. Vigor-2920
    5. /
  5. 3
Page 11 / 251 Scroll up to view Page 6 - 10
Vigor2920 Series User’s Guide
1
1
P
P
r
r
e
e
f
f
a
a
c
c
e
e
Vigor2920 series is a broadband router. It integrates IP layer QoS, NAT session/bandwidth
management to help users control works well with large bandwidth.
By adopting hardware-based VPN platform and hardware encryption of AES/DES/3DS, the
router increases the performance of VPN greatly, and offers several protocols (such as
IPSec/PPTP/L2TP) with up to 2 VPN tunnels.
The object-based design used in SPI (Stateful Packet Inspection) firewall allows users to set
firewall policy with ease. CSM (Content Security Management) provides users control and
management in IM (Instant Messenger) and P2P (Peer to Peer) more efficiency than before.
By the way, DoS/DDoS prevention and URL/Web content filter strengthen the security
outside and control inside.
Object-based firewall is flexible and allows your network be safe. In addition, Vigor2920
series supports USB interface for connecting USB printer to share printer or USB storage
device for sharing files.
Vigor2920 series provides two-level management to simplify the configuration of network
connection. The user mode allows user accessing into WEB interface via simple configuration.
However, if users want to have advanced configurations, they can access into WEB interface
through admin mode.
1.1 Web Configuration Buttons Explanation
Several main buttons appeared on the web pages are defined as the following:
Save and apply current settings.
Cancel current settings and recover to the previous saved settings.
Clear all the selections and parameters settings, including selection from
drop-down list. All the values must be reset with factory default settings.
Add new settings for specified item.
Edit the settings for the selected item.
Delete the selected item with the corresponding settings.
Note:
For the other buttons shown on the web pages, please refer to Chapter 4 for detailed
explanation.
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Page 12 / 251
Vigor2920 Series User’s Guide
2
1.2 LED Indicators and Connectors
Before you use the Vigor router, please get acquainted with the LED indicators and connectors
first.
1.2.1 For Vigor2920
LED
Status
Explanation
Blinking
The router is powered on and running normally.
ACT (Activity)
Off
The router is powered off.
On
USB device is connected and ready for use.
USB
Blinking
The data is transmitting.
CSM
On
The profile(s) of CSM (Content Security
Management) for IM/P2P, URL/Web Content Filter
application is enabled from
Firewall >>General
Setup
. (Such profile must be established under
CSM
menu).
WCF
On
The Web Content Filter is active. (It is enabled
from
Firewall >> General Setup
).
On
The WAN1 or WAN2 connection is ready.
WAN1/2
Blinking
It will blink while transmitting data.
On
The DoS/DDoS function is active.
DoS
Blinking
It will blink while an attack is detected.
VPN
On
The VPN tunnel is active.
QoS
On
The QoS function is active.
LED on Connector
On
The port is connected.
Off
The port is disconnected.
Left LED
(Green)
Blinking
The data is transmitting.
On
The port is connected with 100Mbps.
WAN 1
Right LED
(Green)
Off
The port is connected with 10Mbps when left LED
is on.
On
The port is connected.
Off
The port is disconnected.
Left LED
(Green)
Blinking
The data is transmitting.
On
The port is connected with 1000Mbps.
WAN 2 (Giga)
Right LED
(Green)
Off
The port is connected with 10/100Mbps when left
LED is on.
On
The port is connected.
Off
The port is disconnected.
Left LED
(Green)
Blinking
The data is transmitting.
On
The port is connected with 1000Mbps.
GigaLAN
1/2/3/4
Right LED
(Green)
Off
The port is connected with 10/100Mbps when left
LED is on.
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Page 13 / 251
Vigor2920 Series User’s Guide
3
Interface
Description
Factory Reset
Restore the default settings. Usage: Turn on the router (ACT LED is blinking).
Press the hole and keep for more than 5 seconds. When you see the ACT LED
begins to blink rapidly than usual, release the button. Then the router will restart
with the factory default configuration.
GigaLAN (1-4)
Connecters for local networked devices.
WAN1/WAN2(Giga)
Connecters for remote networked devices.
USB
Connecter for 3G Modem or printer.
PWR
Connecter for a power adapter.
ON/OFF
Power Switch.
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Page 14 / 251
Vigor2920 Series User’s Guide
4
1.2.2 For Vigor2920n
LED
Status
Explanation
Blinking
The router is powered on and running normally.
ACT (Activity)
Off
The router is powered off.
On
USB device is connected and ready for use.
USB
Blinking
The data is transmitting.
CSM
On
The profile(s) of CSM (Content Security
Management) for IM/P2P, URL/Web Content Filter
application is enabled from
Firewall >>General
Setup
. (Such profile must be established under
CSM
menu).
On
Wireless access point is ready.
WLAN
Blinking
It will blink slowly while wireless traffic goes
through.
If ACT and WLAN LEDs blink quickly and
simultaneously when WPS is working, and it will
return to normal condition after two minutes. (You
need to setup WPS within 2 minutes.)
On
The WAN1 or WAN2 connection is ready.
WAN1/2
Blinking
It will blink while transmitting data.
On
The DoS/DDoS function is active.
DoS
Blinking
It will blink while an attack is detected.
VPN
On
The VPN tunnel is active.
QoS
On
The QoS function is active.
LED on Connector
On
The port is connected.
Off
The port is disconnected.
Left LED
(Green)
Blinking
The data is transmitting.
On
The port is connected with 100Mbps.
WAN 1
Right LED
(Green)
Off
The port is connected with 10Mbps when left LED
is on.
On
The port is connected.
Off
The port is disconnected.
Left LED
(Green)
Blinking
The data is transmitting.
On
The port is connected with 1000Mbps.
WAN 2 (Giga)
Right LED
(Green)
Off
The port is connected with 10/100Mbps when left
LED is on.
On
The port is connected.
Off
The port is disconnected.
Left LED
(Green)
Blinking
The data is transmitting.
On
The port is connected with 1000Mbps.
GigaLAN
1/2/3/4
Right LED
(Green)
Off
The port is connected with 10/100Mbps when left
LED is on.
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Page 15 / 251
Vigor2920 Series User’s Guide
5
Interface
Description
Wireless LAN
ON/OFF/WPS
Press "Wireless LAN ON/OFF/WPS" button once to wait for client device
making network connection through WPS.
Press "Wireless LAN ON/OFF/WPS" button twice to enable (WLAN LED on)
or disable (WLAN LED off) wireless connection.
Factory Reset
Restore the default settings. Usage: Turn on the router (ACT LED is blinking).
Press the hole and keep for more than 5 seconds. When you see the ACT LED
begins to blink rapidly than usual, release the button. Then the router will restart
with the factory default configuration.
GigaLAN (1-4)
Connecters for local networked devices.
WAN1/WAN2(Giga)
Connecters for remote networked devices.
USB
Connecter for 3G Modem or printer.
PWR
Connecter for a power adapter.
ON/OFF
Power Switch.
VoIPon
www.voipon.co.uk
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299

Rate

4.5 / 5 based on 2 votes.

Popular DrayTek Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top