1. Home
    2. /
  2. Manuals
    3. /
  3. DrayTek
    4. /
  4. Vigor2860Vn-plus
    5. /
  5. 4
Page 16 / 794 Scroll up to view Page 11 - 15
Vigor2860 Series User’s Guide
2
1.1 Web Configuration Buttons Explanation
Several main buttons appeared on the web pages are defined as the following:
Save and apply current settings.
Cancel current settings and recover to the previous saved settings.
Clear all the selections and parameters settings, including selection from
drop-down list. All the values must be reset with factory default settings.
Add new settings for specified item.
Edit the settings for the selected item.
Delete the selected item with the corresponding settings.
Note:
For the other buttons shown on the web pages, please refer to Chapter 3, 4 for detailed
explanation.
Page 17 / 794
Vigor2860 Series User’s Guide
3
1.2 LED Indicators and Connectors
Before you use the Vigor router, please get acquainted with the LED indicators and connectors
first.
1.2.1 For Vigor2860
LED
Status
Explanation
Blinking
The router is powered on and running normally.
ACT (Activity)
Off
The router is powered off.
On
Internet connection is ready.
Off
Internet connection is not ready.
WAN2
Blinking
The data is transmitting.
QoS
On
The QoS function is active.
On
USB device is connected and ready for use.
USB1~2
Blinking
The data is transmitting.
On
The router is ready to access Internet through DSL link.
DSL
Blinking
Slowly: The DSL connection is ready.
Quickly: The connection is training.
WCF
On
The Web Content Filter is active. (It is enabled from
Firewall >> General Setup
).
On
The VPN tunnel is active.
Off
VPN services are disabled
VPN
Blinking
Traffic is passing through VPN tunnel.
On
The DoS function is active.
DoS
Blinking
It will blink while detecting an attack.
LED on Connector
On
The port is connected.
Off
The port is disconnected.
Left
LED
Blinking
The data is transmitting.
On
The port is connected with 1000Mbps.
WAN2
(Giga)
Right
LED
Off
The port is connected with 10/100Mbps
On
The port is connected.
Off
The port is disconnected.
Left
LED
Blinking
The data is transmitting.
On
The port is connected with 1000Mbps.
GigaLAN
1~6
Right
LED
Off
The port is connected with 10/100Mbps
Page 18 / 794
Vigor2860 Series User’s Guide
4
Interface
Description
Factory Reset
Restore the default settings. Usage: Turn on the router (ACT LED is
blinking). Press the hole and keep for more than 5 seconds. When you
see the ACT LED begins to blink rapidly than usual, release the button.
Then the router will restart with the factory default configuration.
USB
Connecter for a USB device (for 3G/4G USB Modem or printer).
VDSL/ADSL
Connecter for accessing the Internet.
WAN2
Connecter for local network devices or modem for accessing Internet.
GigaLAN (1-6)
Connecters for local network devices.
PWR
Connecter for a power adapter.
ON/OFF
Power Switch.
Page 19 / 794
Vigor2860 Series User’s Guide
5
1.2.2 For Vigor2860ac / Vigor2860n-plus / Vigor2860n
LED
Status
Explanation
Blinking
The router is powered on and running normally.
ACT (Activity)
Off
The router is powered off.
On
Internet connection is ready.
Off
Internet connection is not ready.
WAN2
Blinking
The data is transmitting.
QoS
On
The QoS function is active.
On
USB device is connected and ready for use.
USB
Blinking
The data is transmitting.
On
The router is ready to access Internet through DSL link.
DSL
Blinking
Slowly: The DSL connection is ready.
Quickly: The connection is training.
WCF
On
The Web Content Filter is active. (It is enabled from
Firewall >> General Setup
).
On
2.4G/5G: Wireless access point with bandwidth of
2.4GHz/5GHz is ready.
WLAN: Wireless access point is ready.
2.4G/5G/WLAN
Blinking
It will blink slowly while wireless traffic goes through.
ACT and WLAN LEDs blink quickly and
simultaneously when WPS is working, and will return
to normal condition after two minutes. (You need to
setup WPS within 2 minutes.)
On
The VPN tunnel is active.
Off
VPN services are disabled.
VPN
Blinking
Traffic is passing through VPN tunnel.
On
The DoS function is active.
DoS
Blinking
It will blink while detecting an attack.
LED on Connector
On
The port is connected.
Off
The port is disconnected.
WAN2
(Giga)
Left
LED
Blinking
The data is transmitting.
Page 20 / 794
Vigor2860 Series User’s Guide
6
On
The port is connected with 1000Mbps.
Right
LED
Off
The port is connected with 10/100Mbps
On
The port is connected.
Off
The port is disconnected.
Left
LED
Blinking
The data is transmitting.
On
The port is connected with 1000Mbps.
GigaLAN
1~6
Right
LED
Off
The port is connected with 10/100Mbps
Interface
Description
Wireless LAN
ON/OFF/WPS
For Vigor2860n :
Press the button and release it within 2 seconds. When the
wireless function is ready, the green LED will be on.
Press the button and release it within 2 seconds to turn off the
WLAN function. When the wireless function is not ready, the
LED will be off.
For Vigor2860ac/Vigor2860n-plus :
Wireless band will be switched /changed according to the button
pressed and released. For example,
2.4G (On) and 5G (On) – in default.
2.4G (Off) and 5G (On) – pressed and released the button once.
2.4G (On) and 5G (Off) – pressed and released the button
twice.
2.4G (Off) and 5G (Off) – pressed and released the button three
times.
When WPS function is enabled by web user interface, press this
button for more than 2 seconds to wait for client’s device making
network connection through WPS.
Factory Reset
Restore the default settings. Usage: Turn on the router (ACT LED
is blinking). Press the hole and keep for more than 5 seconds.
When you see the ACT LED begins to blink rapidly than usual,

Rate

4.5 / 5 based on 2 votes.

Popular DrayTek Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top