1. Home
    2. /
  2. Manuals
    3. /
  3. DrayTek
    4. /
  4. Vigor2860Vn-plus
    5. /
  5. 20
Page 96 / 794 Scroll up to view Page 91 - 95
Vigor2860 Series User’s Guide
82
Available settings are explained as follows:
Item
Description
Enable
Choose
Yes
to invoke the settings for this WAN interface.
Choose
No
to disable the settings for this WAN interface.
Display Name
Type the description for such WAN interface.
Physical Mode
Display the physical mode of such WAN interface.
Physical Type
You can change the physical type for WAN2 or choose
Auto
negotiation
for determined by the system.
Line Speed
If your choose
According to Line Speed
as the
Load
Balance Mode
, please type the line speed for downloading
and uploading for such WAN interface. The unit is kbps.
VLAN Tag insertion
Enable
– Enable the function of VLAN with tag.
The router will add specific VLAN number to all packets on
the WAN while sending them out.
Please type the tag value and specify the priority for the
packets sending by WAN1.
Disable
– Disable the function of VLAN with tag.
Tag value
– Type the value as the VLAN ID number. The
range is form 0 to 4095.
Priority
– Type the packet priority number for such VLAN.
The range is from 0 to 7.
Active Mode
Choose
Always On
to make the WAN2 connection being
activated always.
Load Balance
: Check this box to enable
auto
load balance
function for such WAN interface.
When the data traffic is large, the WAN interface with the
function enabled will balance the data transmission
automatically among all of the WAN interfaces in
connection status.
Page 97 / 794
Vigor2860 Series User’s Guide
83
Backup Type
If you choose
Backup
as the
Active Mode
,
Backup Type
will appear. Please specify which WAN will be treated as
the Backup WAN.
When any of selected WAN disconnect
– Such backup
WAN will be activated when any master WAN interface
disconnects.
When all of selected WAN disconnect
– Such backup
WAN will be activated only when all master WAN
interfaces disconnect.
After finished the above settings, click
OK
to save the settings.
WAN3/WAN4 with USB
To use 3G/4G network connection through 3G/4G USB Modem, please configure
WAN3
or
WAN4
interface.
Available settings are explained as follows:
Item
Description
Enable
Choose
Yes
to invoke the settings for this WAN interface.
Choose
No
to disable the settings for this WAN interface.
Display Name
Type the description for such WAN interface.
Physical Mode
Display the physical mode of such WAN interface.
Line Speed
If your choose
According to Line Speed
as the
Load
Balance Mode
, please type the line speed for downloading
and uploading for such WAN interface. The unit is kbps.
Page 98 / 794
Vigor2860 Series User’s Guide
84
Active Mode
Choose
Always On
to make the WAN3 connection being
activated always.
Load Balance
: Check this box to enable
auto
load balance
function for such WAN interface.
When the data traffic is large, the WAN interface with the
function enabled will balance the data transmission
automatically among all of the WAN interfaces in connection
status.
Backup Type
If you choose
Backup
as the
Active Mode
,
Backup Type
will appear. Please specify which WAN will be treated as the
Backup WAN.
When any of selected WAN disconnect
– Such backup
WAN will be activated when any master WAN interface
disconnects.
When all of selected WAN disconnect
– Such backup WAN
will be activated only when all master WAN interfaces
disconnect.
After finished the above settings, click
OK
to save the settings.
Page 99 / 794
Vigor2860 Series User’s Guide
85
3.1.3 Internet Access
For the router supports multi-WAN function, the users can set different WAN settings (for
WAN1/WAN2/WAN3/WAN4) for Internet Access. Due to different Physical Mode for WAN
interface, the Access Mode for these connections also varies. Refer to the following figures.
Available settings are explained as follows:
Item
Description
Index
Display the WAN interface.
Display Name
It shows the name of the WAN1/WAN2/WAN3/WAN4
that entered in general setup.
Physical Mode
It shows the physical connection for
WAN1(ADSL/VDSL2) /WAN2 (Ethernet) /WAN3/WAN4
Page 100 / 794
Vigor2860 Series User’s Guide
86
(3G/4G USB Modem) according to the real network
connection.
Access Mode
Use the drop down list to choose a proper access mode. The
details page of that mode will be popped up. If not, click
Details Page for accessing the page to configure the
settings.
Details Page
This button will open different web page (based on IPv4)
according to the access mode that you choose in WAN
interface.
Note that
Details Pag
e will be changed slightly based on
ADSL/VDSL2 physical mode specified on
WAN>>General Setup
.
IPv6
This button will open different web page (based on Physical
Mode) to setup IPv6 Internet Access Mode for WAN
interface.
If IPv6 service is active on this WAN interface, the color of
“IPv6” will become green.
Advanced
This button allows you to configure DHCP client options.
DHCP packets can be processed by adding option number
and data information when such function is enabled and
configured.
Enable/Disable
– Enable/Disable the function of DHCP
Option. Each DHCP option is composed by an option
number with data. For example,
Option number:100
Data: abcd
When such function is enabled, the specified values for
DHCP option will be seen in DHCP reply packets.
Interface
– Specify the WAN interface(s) that will be
overwritten by such function. WAN5 ~ WAN7 can be
located under
WAN>>Multi-PVC/VLAN
.
Option Number
– Type a number for such function.
Note
:
If you choose to configure option 61 here, the
detailed settings in
WAN>>Interface Access
will be

Rate

4.5 / 5 based on 2 votes.

Popular DrayTek Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top