1. Home
    2. /
  2. Manuals
    3. /
  3. DrayTek
    4. /
  4. Vigor2860Vn-plus
    5. /
  5. 116
Page 576 / 794 Scroll up to view Page 571 - 575
Vigor2860 Series User’s Guide
562
percent
It means to specify the percentage of ADSL transmission
packet. Available range is 10-100.
Example
> adsl txpct auto
% tx percentage : 80
> adsl txpct 75
% tx percentage : 75
Telnet Command: adsl status
This command is used to display current status of ADSL setting.
Syntax
adsl status
Example
> adsl status
--------------------------- ATU-R Info (hw: annex A, f/w: annex Unknown) -----
Running Mode
:
T1.413
State
: TRAINING
DS Actual Rate
:
0 bps US Actual Rate
:
0 bps
DS Attainable Rate
:
0 bps US Attainable Rate:
0 bps
DS Path Mode
:
Fast
US Path Mode
:
Fast
DS Interleave Depth
:
0
US Interleave Depth:
0
NE Current Attenuation
:
0 dB
Cur SNR Margin
:
0 dB
DS actual PSD
:
0. 0 dB
US actual PSD
:
0. 0 dB
ADSL Firmware Version
: 05-04-08-00-00-06
--------------------------- ATU-C Info ---------------------------------
Far Current Attenuation :
0 dB
Far SNR Margin :
0
dB
CO ITU Version[0]
: 00000000
CO ITU Version[1]
: 00000000
DSLAM CHIPSET VENDOR
: < ADI >
>
Telnet Command: adsl ppp
This command can set the Internet Access mode for the router.
Syntax
adsl ppp
[ ? | pvc_no vci vpi Encap Proto modu acqIP idle [Username Password]
Syntax Description
Parameter
Description
Page 577 / 794
Vigor2860 Series User’s Guide
563
?
Display the command syntax of “adsl ppp”.
pvc_no
It means the PVC number and the adjustable range is from
0 (Channel-1) to 7(Channel-8).
Encap
Different numbers represent different modes.
0 : VC_MUX,
1: LLC/SNAP,
2: LLC_Bridge,
3: LLC_Route,
4: VCMUX_Bridge
5: VCMUX_Route,
6: IPoE.
Proto
It means the protocol used to connect Internet. Different
numbers represent different protocols.
0: PPPoA,
1: PPPoE,
2: MPoA.
Modu
0: T1.413,
2: G.dmt,
4: Multi,
5: ADSL2,
7:ADSL2_AnnexM
8:ADSL2+
14:ADSL2+_AnnexM.
acqIP
It means the way to acquire IP address. Type the number to
determine the IP address by specifying or assigned
dynamically by DHCP server.
0 : fix_ip,
1: dhcp_client/PPPoE/PPPoA.(acquire IP method)
idle
Type number to determine the network connection will be
kept for always or idle after a certain time.
1: always on, else idle timeout secs. Only for
PPPoE/PPPoA.
Username
This parameter is used only for PPPoE/PPPoA
Password
This parameter is used only for PPPoE/PPPoA
You have to reboot the system when you set it on Route mode.
Example
> adsl ppp o 35 8 1 1 4 1 -1 draytek draytek
pvc no.=0
vci=35
vpi=8
Page 578 / 794
Vigor2860 Series User’s Guide
564
encap=LLC(1)
proto=PPPoE(1)
modu=MULTI(4)
AcquireIP: Dhcp_client(1)
Idle timeout:-1
Username=draytek
Password=draytek
Telnet Command: adsl bridge
This command can specify a LAN port (LAN1 to LAN4) for mapping to certain PVC, and the
mapping port/PVC will be operated in bridge mode.
adsl bridge
[pvc_no/status/save/enable/disable] [on/off/clear/tag tag_no] [service type]
[px ... ]
Syntax Description
Parameter
Description
pvc_no
It means
pvc
number and must be between 0(Channel
1) to 7(Channel 8).
status
It means to shown the whole bridge status.
save
It means to save the configuration to flash.
enable
It means to enable the Multi-VLAN function.
disable
It means to disable the Multi-VLAN function.
on/off
It means to turn on/off bridge mode for the specific
channel.
clear
It means to turn off and clear all the PVC settings.
tag tag_no
No tag: -1
Available number for tag: 0-4095
pri pri_no
The number 0 to 7 can be set to indicate the priority.
“7” is the highest.
service type
Two number can be set:
0: for Normal (all the applications will be processed
with the same PVC).
Page 579 / 794
Vigor2860 Series User’s Guide
565
1: for the IGMP with different PVC which is used for
special ISP.
px…
It means the number of LAN port (x=2~4). Port 1 is
locked for NAT.
Example
> adsl bridge 4 on p2 p3
PVC
Bridge
p1
p2
p3
p4
Service Type
Tag
Pri
------------------------------------------------------------
4
ON
0
0
1
0
Normal
-1(OFF)
0
PVC 0 & 1 can't set for bridge mode.
Please use 'save' to save config.
Telnet Command: adsl idle
This command can make the router accessing into the idle status. If you want to invoke the
router again, you have to reboot the router by using “reboot” command.
Example
> adsl idle
%Idle Mode!
You has to use {adsl reboot} to restart booting.
Telnet Command: adsl drivemode
This command is useful for laboratory to measure largest power of data transmission. Please
follow the steps below to set adsl drivermode.
1. Please connect dsl line to the DSLAM.
2. Waiting for dsl SHOWTIME.
3. Drop the dsl line.
4. Now, it is on continuous sending mode, and adsl2/2+ led is always ON.
5. Use 'adsl reboot' to restart dsl to normal mode.
Telnet Command: adsl reboot
This command can wake up the idle router.
Example
> adsl reboot
% Adsl is Rebooting...
Page 580 / 794
Vigor2860 Series User’s Guide
566
Telnet Command: adsl oamlb
This command is used to test if the connection between CPE and CO is OK or not.
adsl oamlb
[n][type]
adsl oamlb chklink
[on/off]
adsl oamlb
[log_on/log_off]
Syntax Description
Parameter
Description
n
It means the total number of transmitted packets.
type
It means the protocol that you can use.
1 – for F4 Seg-to-Seg (VP level)
2 – for F4 End-to-End (VP level)
4 – for F5 Seg-to-Seg (VC level)
5 – for F5 End-to-End (VC level)
chklink
Check the DSL connection.
Log_on/log_off
Enable or disable the OAM log for debug.
Example
> adsl oamlb chklink on
OAM checking dsl link is ON.
> adsl oamlb F5 4
Tx cnt=0
Rx Cnt=0
>
Telnet Command: adsl vcilimit
This command can cancel the limit for vci value.
Some ISP might set the vci value under 32. In such case, we can cancel such limit manually by
using this command. Do not set the number greater than 254.
adsl vcilimit
[n]
Syntax Description
Parameter
Description
n
The number shall be between 1 ~ 254.
Example

Rate

4.5 / 5 based on 2 votes.

Popular DrayTek Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top