DrayTek Vigor2860n-plus Router Manual PDF (Setup & Configuration Guide)

Page 376 / 794 Scroll up to view Page 371 - 375

Vigor2860 Series User’s Guide

362

Voice Active Detector

This function can detect if the voice on both sides is active

or not. If not, the router will do something to save the

bandwidth for other using. Click On to invoke this function;

click off to close the function.

After finishing all the settings here, please click

OK

to save the configuration.

3.15.3 Phone Settings

This page allows user to set phone settings for Phone 1 and Phone 2 respectively. However, it

changes slightly according to different model you have.

Available settings are explained as follows:

Item

Description

Phone List

Port –

there are two phone ports provided here for you to

configure.

Phone1/Phone2

allows you to set general

settings for PSTN phones.

Call Feature

– A brief description for call feature will be

shown in this field for your reference.

Tone

- Display the tone settings that configured in the

advanced settings page of Phone Index.

Gain

- Display the volume gain settings for Mic/Speaker

that configured in the advanced settings page of Phone

Index.

Default SIP Account

– “draytel_1” is the default SIP

account. You can click the number below the Index field to

Page 377 / 794

Vigor2860 Series User’s Guide

363

change SIP account for each phone port.

DTMF Relay

– Display DTMF mode that configured in the

advanced settings page of Phone Index.

RTP

Symmetric RTP

– Check this box to invoke the function.

To make the data transmission going through on both ends

of local router and remote router not misleading due to IP

lost (for example, sending data from the public IP of remote

router to the private IP of local router), you can check this

box to solve this problem.

Dynamic RTP Port Start

- Specifies the start port for RTP

stream. The default value is 10050.

Dynamic RTP Port End

- Specifies the end port for RTP

stream. The default value is 15000.

RTP TOS

– It decides the level of VoIP package. Use the

drop down list to choose any one of them.

After finishing all the settings here, please click

OK

to save the configuration.

Page 378 / 794

Vigor2860 Series User’s Guide

364

Detailed Settings for Phone Port

Click the number link for Phone port, you can access into the following page for configuring

Phone settings.

Available settings are explained as follows:

Item

Description

Hotline

Check the box to enable it. Type in the SIP URL in the field

for dialing automatically when you pick up the phone set.

Session Timer

Check the box to enable the function. In the limited time

that you set in this field, if there is no response, the

connecting call will be closed automatically.

T.38 Fax Function

Check the box to enable T.38 fax function.

Error Correction Mode –

choose a mode for error

correction.

DND (Do Not Disturb)

mode

Set a period of peace time without disturbing by VoIP

phone call. During the period, the one who dial in will listen

busy tone, yet the local user will not listen any ring tone.

Index (1-15) in Schedule -

Enter the index of schedule

profiles to control when the phone will ring and when will

not according to the preconfigured schedules. Refer to

section

Application >>Schedule

for detailed configuration.

Index (1-60) in Phone Book -

Enter the index of phone

book profiles. Refer to section

DialPlan – Phone Book

for

detailed configuration.

CLIR (hide caller ID)

Check this box to hide the caller ID on the display panel of

the phone set.

Call Waiting

Check this box to invoke this function. A notice sound will

appear to tell the user new phone call is waiting for your

Page 379 / 794

Vigor2860 Series User’s Guide

365

response. Click hook flash to pick up the waiting phone

call.

Call Transfer

Check this box to invoke this function. Click hook flash to

initiate another phone call. When the phone call connection

succeeds, hang up the phone. The other two sides can

communicate, then.

Default SIP Account

You can set SIP accounts (up to six groups) on SIP Account

page. Use the drop down list to choose one of the profile

names for the accounts as the default one for this phone

setting.

Play dial tone only when account registered -

Check this

box to invoke the function.

In addition, you can press the

Advanced

button to configure tone settings, volume gain, MISC

and DTMF mode.

Advanced

setting is provided for fitting the telecommunication custom for

the local area of the router installed. Wrong tone settings might cause inconvenience for users.

To set the sound pattern of the phone set, simply choose a proper region to let the system find

out the preset tone settings and caller ID type automatically. Or you can adjust tone settings

manually if you choose User Defined. TOn1, TOff1, TOn2 and TOff2 mean the cadence of the

tone pattern. TOn1 and TOn2 represent sound-on; TOff1 and TOff2 represent the sound-off.

Available settings are explained as follows:

Item

Description

Region

Select the proper region which you are located. The

common settings of

Caller ID Type

,

Dial tone

,

Ringing

tone

,

Busy tone

and

Congestion tone

will be shown

automatically on the page. If you cannot find out a suitable

one, please choose

User Defined

and fill out the

corresponding values for dial tone, ringing tone, busy tone,

Page 380 / 794

Vigor2860 Series User’s Guide

366

congestion tone by yourself for VoIP phone.

Also, you can specify each field for your necessity. It is

recommended for you to use the default settings for VoIP

communication.

Volume Gain

Mic Gain (1-10)/Speaker Gain (1-10)

- Adjust the volume

of microphone and speaker by entering number from 1- 10.

The larger of the number, the louder the volume is.

MISC

Dial Tone Power Leve

l - This setting is used to adjust the

loudness of the dial tone. The smaller the number is, the

louder the dial tone is.

It is recommended for you to use the

default setting.

Call Waiting Tone Power Level

- This setting is used to

adjust the loudness of the call waiting tone. The smaller the

number is, the louder the tone is.

It is recommended for you

to use the default setting.

Interdigit Timeout

–Type a value in this field to specify

time limit for interdigit.

DTMF

DTMF Mode –

There are four DTMF modes for you to

choose.



InBand

-

Choose this one then the Vigor will send the

DTMF tone as audio directly when you press the

keypad on the phone.



OutBand

-

Choose this one then the Vigor will

capture the keypad number you pressed and transform

Rate

Popular DrayTek Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share