Page 221 / 794
Scroll up to view Page 216 - 220
Vigor2860 Series User’s Guide
207
3.7.2 IP Group
This page allows you to bind several IP objects into one IP group.
Available settings are explained as follows:
Item
Description
Set to Factory Default
Clear all profiles.
Index
Display the profile number that you can configure.
Name
Display the name of the group profile.
To set a new profile, please do the steps listed below:
1.
Click the number (e.g., #1) under Index column for configuration in details.
2.
The configuration page will be shown as follows:
Page 222 / 794
Vigor2860 Series User’s Guide
208
Available settings are explained as follows:
Item
Description
Name
Type a name for this profile. Maximum 15 characters are
allowed.
Interface
Choose WAN, LAN or Any to display all the available IP
objects with the specified interface.
Available IP Objects
All the available IP objects with the specified interface
chosen above will be shown in this box.
Selected IP Objects
Click
>>
button to add the selected IP objects in this box.
3.
After finishing all the settings here, please click
OK
to save the configuration.
3.7.3 IPv6 Object
You can set up to 64 sets of IPv6 Objects with different conditions.
Available settings are explained as follows:
Item
Description
Set to Factory Default
Clear all profiles.
Index
Display the profile number that you can configure.
Name
Display the name of the object profile.
Page 223 / 794
Vigor2860 Series User’s Guide
209
To set a new profile, please do the steps listed below:
1.
Click the number (e.g., #1) under Index column for configuration in details.
2.
The configuration page will be shown as follows:
Available settings are explained as follows:
Item
Description
Name
Type a name for this profile. Maximum 15 characters are
allowed.
Address Type
Determine the address type for the IPv6 address.
Select
Single Address
if this object contains one IPv6
address only.
Select
Range Address
if this object contains several IPv6s
within a range.
Select
Subnet Address
if this object contains one subnet
for IPv6 address.
Select
Any Address
if this object contains any IPv6
address.
Select
Mac Address
if this object contains Mac address.
Mac Address
Type the MAC address of the network card which will be
controlled.
Start IP Address
Type the start IP address for Single Address type.
End IP Address
Type the end IP address if the Range Address type is
selected.
Prefix Length
Type the number (e.g., 64) for the prefix length of IPv6
address.
Invert Selection
If it is checked, all the IPv6 addresses except the ones listed
above will be applied later while it is chosen.
Page 224 / 794
Vigor2860 Series User’s Guide
210
3.
After finishing all the settings, please click
OK
to save the configuration.
3.7.4 IPv6 Group
This page allows you to bind several IPv6 objects into one IPv6 group.
Available settings are explained as follows:
Item
Description
Set to Factory Default
Clear all profiles.
Index
Display the profile number that you can configure.
Name
Display the name of the group profile.
To set a new profile, please do the steps listed below:
1.
Click the number (e.g., #1) under Index column for configuration in details.
2.
The configuration page will be shown as follows:
Page 225 / 794
Vigor2860 Series User’s Guide
211
Available settings are explained as follows:
Item
Description
Name
Type a name for this profile. Maximum 15 characters are
allowed.
Available IPv6
Objects
All the available IPv6 objects with the specified interface
chosen above will be shown in this box.
Selected IPv6 Objects
Click
>>
button to add the selected IPv6 objects in this box.
3.
After finishing all the settings, please click
OK
to save the configuration.
3.7.5 Service Type Object
You can set up to 96 sets of Service Type Objects with different conditions.
Available settings are explained as follows:
Item
Description
Set to Factory Default
Clear all profiles.
Index
Display the profile number that you can configure.
Name
Display the name of the object profile.
19216811.live