DrayTek Vigor-2710n Router Manual PDF (Setup & Configuration Guide)

Page 236 / 335 Scroll up to view Page 231 - 235

Vigor2710 Series User’s Guide

224

SIP Accounts Web Page for Vigor2710 VDn -------

Profile Name

Assign a name for this profile for identifying. You can type

similar name with the domain. For example, if the domain

name is

draytel.org

, then you might set

draytel-1

in this field.

Register via

If you want to make VoIP call without register personal

information, please choose

None

and check the box to achieve

the goal.

Some SIP server allows user to use VoIP function

without registering. For such server, please check the box of

Call without registration

. Choosing

Auto

is recommended.

SIP Port

Set the port number for sending/receiving SIP message for

building a session. The default value is

5060.

Your peer must

set the same value in his/her Registrar.

Domain/Realm

Set the domain name or IP address of the SIP Registrar server.

Proxy

Set domain name or IP address of SIP proxy server. By the

time you can type

:port

number

after the domain name to

specify that port as the destination of data transmission (e.g.,

nat.draytel.org:5065

)

Act as Outbound Proxy

Check this box to make the proxy acting as outbound proxy.

Page 237 / 335

Vigor2710 Series User’s Guide

225

Display Name

The caller-ID that you want to be displayed on your friend’s

screen.

Account Number/Name

Enter your account name of SIP Address, e.g. every text

before @.

Authentication ID

Check the box to invoke this function and enter the name or

number used for SIP Authorization with SIP Registrar. If this

setting value is the same as Account Name, it is not necessary

for you to check the box and set any value in this field.

Password

The password provided to you when you registered with a SIP

service.

Expiry Time

The time duration that your SIP Registrar server keeps your

registration record. Before the time expires, the router will

send another register request to SIP Registrar again.

NAT Traversal Support

If the router (e.g.

,

broadband router) you use connects to

internet by other device, you have to set this function for your

necessity.

None –

Disable this function.

Stun

– Choose this option if there is Stun server provided for

your router.

Manual

– Choose this option if you want to specify an

external IP address as the NAT transversal support.

Nortel

– If the soft-switch that you use supports Nortel

solution, you can choose this option.

Ring Port

Set Phone or DECT as the default ring port for this SIP

account. The ports you can set are different based on the

model you have.

Ring Pattern

Choose a ring tone type for the VoIP phone call.

Prefer Codec

Select one of the codecs as the default for your VoIP calls. The

codec used for each call will be negotiated with the peer party

before each session, and so may not be your default choice.

The default codec is G.729A/B; it occupies little bandwidth

while maintaining good voice quality.

If your upstream speed is only 64Kbps, do not use G.711

codec. It is better for you to have at least 256Kbps upstream if

you would like to use G.711.

Page 238 / 335

Vigor2710 Series User’s Guide

226

Single Codec

– If the box is checked, only the selected Codec

will be applied.

Packet Size

The amount of data contained in a single packet. The default

value is 20 ms, which means the data packet will contain 20

ms voice information.

Voice Active Detector

This function can detect if the voice on both sides is active or

not. If not, the router will do something to save the bandwidth

for other using. Click

On

to invoke this function; click

Off

to

close the function.

Page 239 / 335

Vigor2710 Series User’s Guide

227

4.11.3 Phone Settings

This page allows user to set phone settings for Phone 1 and Phone 2 respectively. However,

it changes slightly according to different model you have.

Phone Settings Web Page for Vigor2710 Vn -------

Phone Settings Web Page for Vigor2710 VDn -------

Phone List

Port – Phone, Phone1/Phone2

allow you to set general

settings for PSTN phones. DECT1-6 allow you to set general

settings for DECT phone.

Call Feature

– A brief description for call feature will be

shown in this field for your reference.

Page 240 / 335

Vigor2710 Series User’s Guide

228

Codec

– The default Codec setting for each port will be shown

in this field for your reference. You can click the number

below the Index field to change it for each phone port.

Tone

- Display the tone settings that configured in the

advanced settings page of Phone Index.

Gain

- Display the volume gain settings for Mic/Speaker that

configured in the advanced settings page of Phone Index.

Default SIP Account

– “draytel_1” is the default SIP account.

You can click the number below the Index field to change SIP

account for each phone port.

DTMF Relay

– Display DTMF mode that configured in the

advanced settings page of Phone Index.

Disable Port: Phone

If Phone port is disabled, Phone could not be used anymore.

However, its DSP resource could be used by DECT and DECT

could dial 4 VoIP calls at the same time.

Otherwise, DECT could only dial 3 VoIP calls at the same

time.

RTP

Symmetric RTP

– Check this box to invoke the function. To

make the data transmission going through on both ends of

local router and remote router not misleading due to IP lost

(for example, sending data from the public IP of remote router

to the private IP of local router), you can check this box to

solve this problem.

Dynamic RTP Port Start

- Specifies the start port for RTP

stream. The default value is 10050.

Dynamic RTP Port End

- Specifies the end port for RTP

stream. The default value is 15000.

RTP TOS

– It decides the level of VoIP package. Use the

drop down list to choose any one of them.

Rate

Popular DrayTek Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share