Page 21 / 335
Scroll up to view Page 16 - 20
Vigor2710 Series User’s Guide
9
Interface
Description
WLAN
Press the button once to enable (WLAN LED on) or
disable (WLAN LED off) wireless connection.
DSL
Connector for accessing the Internet through ADSL2/2+.
LAN (1-4)
Connectors for local networked devices.
USB
Connector for USB storage (Pen Driver/Mobile HD) or
printer.
Interface
Description
Line
Connector for PSTN life line.
Phone
Connector of analog phone for VoIP communication
.
Factory Reset
Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the
hole and keep for more than 5 seconds. When you see the ACT LED begins to blink
rapidly than usual, release the button. Then the router will restart with the factory default
configuration.
PWR
Connector for a power adapter.
ON/OFF
Power Switch.
Page 22 / 335
Vigor2710 Series User’s Guide
10
1.3 Hardware Installation
Before starting to configure the router, you have to connect your devices correctly.
1.
Connect the ADSL interface to the external ADSL splitter with an ADSL line cable for
all models. For Vigor2710Vn/VDn, also connect Line interface to external ADSL
splitter.
2.
Connect one end of an Ethernet cable (RJ-45) to one of the
LAN
ports of the router and
the other end of the cable (RJ-45) into the Ethernet port on your computer.
3.
Connect the telephone sets with phone lines (for using VoIP function). For the model
without phone ports, skip this step.
4.
Connect one end of the power adapter to the router’s power port on the rear panel, and
the other side into a wall outlet.
5.
Power on the device by pressing down the power switch on the rear panel.
6.
The system starts to initiate. After completing the system test, the
ACT
LED will light
up and start blinking.
Here, we take
Annex A
model as an example for describing hardware installation.
Page 23 / 335
Vigor2710 Series User’s Guide
11
Caution
:
1. Each of the Phone ports can be connected to an analog phone only. Do not connect
the phone ports to the land line jack. Such connection might damage your router.
2. When the power is shutdown, VoIP phone will be disconnected. However, a phone
set connected to Phone 2 port can be used as the traditional telephone for the line will
be guided to land line jack via the router (loop through).
1.4 Printer Installation
You can install a printer onto the router for sharing printing. All the PCs connected this
router can print documents via the router. The example provided here is made based on
Windows XP/2000. For Windows 98/SE/Vista, please visit
www.draytek.com
.
Before using it, please follow the steps below to configure settings for connected computers
(or wireless clients).
1.
Connect the printer with the router through USB/parallel port.
2.
Open
Start->Settings-> Printer and Faxes
.
3.
Open
File->Add a New Computer
. A welcome dialog will appear. Please click
Next
.
Page 24 / 335
Vigor2710 Series User’s Guide
12
4.
Click Local printer attached to this computer and click Next.
5.
In this dialog, choose
Create a new port Type of port
and use the drop down list to
select
Standard TCP/IP Port
. Click
Next
.
Page 25 / 335
Vigor2710 Series User’s Guide
13
6.
In the following dialog, type
192.168.1.1
(router’s LAN IP) in the field of
Printer
Name or IP Address
and type
IP_192.168.1.1
as the port name. Then, click
Next
.
7.
Click Standard and choose Generic Network Card.
8.
Then, in the following dialog, click
Finish
.
19216811.live