1. Home
    2. /
  2. Manuals
    3. /
  3. DrayTek
    4. /
  4. Vigor2130n
    5. /
  5. 21
Page 101 / 241 Scroll up to view Page 96 - 100
Vigor2130 Series User’s Guide
93
Destination Subnet
Type the subnet mask here if you choose
Subnet
as
Destination IP Type
.
Source Start Port
Type a value as the source start port. Such value will be
available only TCP/UDP is selected as the protocol.
Source End Port (optional)
Type a value as the source end port. Such value will be
available only TCP/UDP is selected as the protocol.
Destination Start Port
Type a value as the destination start port. Such value will
be available only TCP/UDP is selected as the protocol.
Destination End Port (optional)
Type a value as the destination end port. Such value will be
available only TCP/UDP is selected as the protocol.
Action
Set the action that the router will perform for the packets
through the protocol of IPv6.
Accept –
If the IPv6 packets fit the condition listed in this
page, the router will let it pass through.
Drop -
If the IPv6 packets fit the condition listed in this
page, the router will block it.
3.8.4 IPv6 Routing
This page displays the routing table for the protocol of IPv6.
Device
Display the
interface name (eth0, eth1, fp, etc..)that
used to transfer packets with addresses matching the
prefix.
Prefix
The IPv6 address prefix.
Metric
Display the
distance to the target (usually counted in
hops). It is not used by recent kernels, but may be
needed by routing daemons.
Expires
Display the lifetime of the route.
MTU
Display t
he largest size (in bytes) of a packet.
Advmss
Display t
he largest size (in bytes) of an unfragmented
piece of a routing advertisement.
Page 102 / 241
Vigor2130 Series User’s Guide
94
Hoplimit
Display t
he number of network segments on which the
packet is allowed to travel before discarded.
Auto-refresh
Check this box to enable an automatic refresh of the page
at regular intervals.
3.8.5 IPv6 Neighbour
IPv6 uses neighbor discovery protocol to find out neighbors on the same link.
Device
The interface name of the link where the neighbor is on.
IP Address
The IPv6 address of the neighbor.
MAC Address
The link-layer address of the neighbor.
State
Possible states include:
incomplete
- address resolution is in progress.
reachable
- neighbor is reachable.
stale
– neighbor(s) may be unreachable but not verified
until a packet is sent).
delay
- neighbor may be unreachable and a packet was sent.
probe
- neighbor may be unreachable and probes are sent
to verify the reachability.
Auto-refresh
Check this box to enable an automatic refresh of the page
at regular intervals.
3.8.6 IPv6 TSPC Status
IPv6 TSPC status web page could help you to diagnose the connection status of TSPC. TSPC
log contains some debug information from program.
If TSPC has not configured properly, the router will display the following page when the user
tries to connect through TSPC connection.
Page 103 / 241
Vigor2130 Series User’s Guide
95
When TSPC configuration has been done, the router will start to connect. The connecting page
will be shown as below:
When the router detects all the information, the screen will be shown as follows. One set of
TSPC prefix
and
prefix length
will be obtained after the connection between TSPC and
Tunnel broker built.
Connection Status
It will bring out different pages to represent IPv6
disconnection, connecting and connected.
Tunnel Information
Display interface name (used to send TSPC prefix), tunnel
mode, local endpoint addresses, remote endpoint address,
TSPC Prfix, TSPC Prefixlen (prefix length), tunnel broker
and so on.
Tunnel Status
Disconnected
- The remote client doesn't connect to the
tunnel server.
Connecting
- The remote client is connecting to the tunnel
server.
Connected
– The remote client has been connected to the
tunnel server.
Activity
Sent -
sent to the tunnel (RX bytes).
Received
- received from the tunnel (RX bytes).
Page 104 / 241
Vigor2130 Series User’s Guide
96
When the router connects to the tunnel broker, the router will use RADVD to transmit the
prefix to the PC on LAN. Next, the PC will generate one set of IPv6 public IP (see the figure
below). Users can use such IP for connecting to IPv6 network.
When your PC obtains the IPv6 address, please connect to http://www.ipv6.org
. If your PC
access Internet via IPv6 connection, your IPv6 address will be shown on the web page
immediately. Refer to the following figure.
Page 105 / 241
Vigor2130 Series User’s Guide
97
3.9 User
3.9.1 User Configuration
This page allows you to set user’s setting that allowed to use PPTP, FTP, IPSEC/L2TP
connection.
Adding a New User
Click
Add a New User
to open the following page.
Username
Type a name for this user.
Full Name
Type full name for this user.
Password
Type the password for this user.
Password (again)
Type the password again for confirmation.
Allow Disk Sharing
Check this box to enable Samba file sharing.
Allow IPSEC/L2TP
Check this box to
let
the user connect via IPSEC/L2TP.
Allow PPTP
Check this box to let
the user connect via PPTP.
Allow FTP
Check this box to let
the user connect to FTP server.
When you finish the settings, simply click
OK
to save the configuration. The new user will be
created and displayed on the page.

Rate

4 / 5 based on 1 vote.

Popular DrayTek Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top