1. Home
    2. /
  2. Manuals
    3. /
  3. DrayTek
    4. /
  4. Vigor2130n
    5. /
  5. 18
Page 86 / 241 Scroll up to view Page 81 - 85
Vigor2130 Series User’s Guide
78
Type
The WPA encrypts each frame transmitted from the radio
using the key, which either PSK (Pre-Shared Key) entered
manually in this field below or automatically negotiated
via 802.1x authentication. Select WPA, WPA2 or Auto as
WPA mode.
WPA Algorithm
Choose the WPA algorithm, TKIP, AES or Auto.
Server IP Address
Enter the IP address of RADIUS server.
Destination Port
The UDP port number that the RADIUS server is using.
The default value is 1812, based on RFC 2138.
Shared Secret
The RADIUS server and client share a secret that is used
to authenticate the messages sent between them. Both
sides must be configured to use the same shared secret.
z
WPS
WPS (Wi-Fi Protected Setup)
provides easy procedure to make network connection
between wireless station and wireless access point (vigor router) with the encryption
of WPA and WPA2.
Configure via Push Button
Click
Start PBC
to invoke Push-Button style WPS setup
procedure. The router will wait for WPS requests from
wireless clients about two minutes. The WPS LED on the
Page 87 / 241
Vigor2130 Series User’s Guide
79
router will blink fast when WPS is in progress. It will
return to normal condition after two minutes. (You need to
setup WPS within two minutes)
Configure via Client PinCode
Type the PIN code specified in wireless client you
wish to connect, and click
Start PIN
button. The WLAN
LED on the router will blink fast when WPS is in progress.
It will return to normal condition after two minutes. (You
need to setup WPS within two minutes
It is the simplest way to build connection between wireless network clients and vigor
router. Users do not need to select any encryption mode and type any long encryption
passphrase to setup a wireless client every time. He/she only needs to press a button on
wireless client, and WPS will connect for client and router automatically.
Note:
Such function is available for the wireless station with WPS supported.
There are two methods to do network connection through WPS between AP and Stations:
pressing the
Start PBC
button or using
PIN Code
.
On the side of Vigor 2130 series which served as an AP, press
WPS
button once on the
front panel of the router or click
Start PBC
on web configuration interface. On the side
of a station with network card installed, press
Start PBC
button of network card.
Page 88 / 241
Vigor2130 Series User’s Guide
80
If you want to use PIN code, you have to know the PIN code specified in wireless client.
Then provide the PIN code of the wireless client you wish to connect to the vigor router.
3.6.3 Access Control
For additional security of wireless access, the
Access Control
facility allows you to restrict
the network access right by controlling the wireless LAN MAC address of client. Only the
valid MAC address that has been configured can access the wireless LAN interface. By
clicking the
Access Control
, a new web page will appear, as depicted below, so that you
could edit the clients' MAC addresses to control their access rights (deny or allow).
Filter Type
Choose the rule for the MAC addresses displayed in this
page.
Allow List
– all the MAC address of wireless clients listed
here are allowed to do wireless connection.
Deny List
– all the MAC address of wireless clients listed
here will be blocked.
Add a New Entry
Add a new MAC address into the list.
Delete
Delete the selected MAC address in the list. This button
will appear only an entry of MAC Address has been typed.
Cancel
Give up the configuration.
Page 89 / 241
Vigor2130 Series User’s Guide
81
OK
Click it to save the configuration.
3.6.4 Station List
Station List
provides the knowledge of connecting wireless clients now along with its status
code.
Index
Display the number of the connecting client.
IP Address
Display the WAN IP address for the connecting client.
MAC Address
Display the MAC Address for the connecting client.
Connected Time
Display the connection time for the connecting client.
SSID
Display the SSID that the station(s) connected through.
Auto-refresh
Check this box to force the system refreshing the table
automatically
.
Refresh
Click this button to refresh current page.
Page 90 / 241
Vigor2130 Series User’s Guide
82
3.6.5 Access Point Discovery
Vigor router can scan all regulatory channels and find working APs in the neighborhood.
Based on the scanning result, users will know which channel is clean for usage.
Note:
During the scanning process (about 5 seconds), no client is allowed to connect to
Vigor.
The table will list channel, SSID, BSSID, Security and the Signal strength of working APs in
the neighborhood.
CH
Display the channel for the scanned AP.
SSID
Display the SSID of the scanned AP.
BSSID
Display the MAC address of the scanned AP.
Security
Display the encryption type of the scanned AP.
Signal
Display the strength (in percentage) of the signal of the
scanned AP.
Scan
It is used to discover all the connected AP. The results will
be shown on the box above this button.
3.7 USB Application
USB diskette can be regarded as an FTP server. By way of Vigor router, uses on LAN/WAN
can access, write and read data stored in USB diskette. After setting the configuration in
USB
Application
, you can type the IP address of the Vigor router and username/password created
in
USB Application>>FTP User Management
on the FTP client software. Thus, the client
can use the FTP site (USB diskette) through Vigor router.
3.7.1 USB General Settings
At present, the Vigor router can support USB diskette with versions of FAT16 and FAT32
only. Therefore, before connecting the USB diskette into the Vigor router, please make sure
the memory format for the USB diskette is FAT16 or FAT32. It is recommended for you to
use FAT32 for viewing the filename completely (FAT16 cannot support long filename).

Rate

4 / 5 based on 1 vote.

Popular DrayTek Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top