Vigor2130 Series User’s Guide

48

To add a new static MAC entry, click

Add new static entry

. A new entry will be shown as

follows. Choose VLAN ID and type a new MAC address. Next, specify port member for this

table. Finally, click OK to save the changes.

3.2.4 VLAN

Virtual LAN function provides you a very convenient way to manage hosts by grouping them

based on the physical port. You can also manage the in/out rate of each port. Go to

LAN

page

and select

VLAN

. The following page will appear. VLAN function is enabled in default.

Add New Private VLAN

Click this button to add a new private VLAN. The router allows

you to add up to 4 VLAN.

Vigor2130 Series User’s Guide

49

To add or remove a VLAN, please refer to the following example.

1.

VLAN 1 is consisted of hosts linked to P1 ~ P4.

2.

After checking the box to enable VLAN function, you will check the table according to

the needs as shown below.

3.

To remove VLAN, click the

Delete

button for the one you want to remove and click

OK

to save the results.

3.2.5 Monitor Port

It is used to monitor the traffic of the network. For example, we assume that LAN1 and LAN2

are Monitor Port and Monitor ingress Port respectively, thus, the traffic received by LAN2

will be copied to LAN1 for monitoring.

Enable Monitor Port

Check to enable this function.

Monitor Port

Click the one of the LAN ports to specify it for monitoring.

Monitor ingress port

Check to set up the port(s) for being monitored. It only

monitors the packets

received b

y the port you set up.

Monitor egress port

Check to set up the port(s) for being monitored. It only

monitors the packets

transmitted

by the port you set up.

Vigor2130 Series User’s Guide

50

3.2.6 Static Route

Go to

LAN

and choose

Static Route

to open setting page.

Index

The number (1 to 10) under Index displays current static router.

Destination Address

Display the destination address of the static route.

Status

Display the status of the static route.

Add

Add a new static route.

Add Static Routes to Private and Public Networks

Here is an example of setting Static Route in Main Router so that user A and B locating in

different subnet can talk to each other via the router. Assuming the Internet access has been

configured and the router works properly:

z

use the Main Router to surf the Internet.

z

create a private subnet 192.168.10.0 using an internal Router A (192.168.1.2)

z

create a public subnet 211.100.88.0 via an internal Router B (192.168.1.3).

z

have set Main Router 192.168.1.1 as the default gateway for the Router A 192.168.1.2.

Before setting Static Route, user A cannot talk to user B for Router A can only forward

recognized packets to its default gateway Main Router.

Vigor2130 Series User’s Guide

51

1.

Click the

LAN - Static Route

and click

Add.

Check the

Enable

box. Please add a static

route as shown below, which regulates all packets destined to 192.168.10.0 will be

forwarded to 192.168.1.2. Click

OK

.

2.

Return to

Static Route

page. Click

Add

again to add another static route as show below,

which regulates all packets destined to 211.100.88.0 will be forwarded to 192.168.1.3.

3.

Verify current routing table.

3.2.7 Bind IP to MAC

This function is used to bind the IP and MAC address in LAN to have a strengthening control

in network. When this function is enabled, all the assigned IP and MAC address binding

together cannot be changed. If you modified the binding IP or MAC address, it might cause

you not access into the Internet.

Click

LAN

and click

Bind IP to MAC

to open the setup page.

Vigor2130 Series User’s Guide

52

Enable

Click this radio button to invoke this function.

However,

IP/MAC which is not listed in IP Bind List also can connect to

Internet.

Disable

Click this radio button to disable this function. All the settings

on this page will be invalid.

Strict Bind

Click this radio button to block the connection of the IP/MAC

which is not listed in IP Bind List.

ARP Table

This table is the LAN ARP table of this router. The information

for IP and MAC will be displayed in this field. Each pair of IP

and MAC address listed in ARP table can be selected and added

to IP Bind List by clicking

Add

below

.

Add and Edit

IP Address

–

Type the IP address that will be used for the

specified MAC address.

Mac Address

–

Type the MAC address that is used to bind

with the assigned IP address.

Refresh

It is used to refresh the ARP table. When there is one new PC

added to the LAN, you can click this link to obtain the newly

ARP table information.

IP Bind List

It displays a list for the IP bind to MAC information.

Add

It allows you to add the one you choose from the ARP table or

the IP/MAC address typed in

Add and Edit

to the table of

IP

Bind List

.

Edit

It allows you to edit and modify the selected IP address and

MAC address that you create before.