DrayTek Vigor 2830 Router Manual PDF (Setup & Configuration Guide)

Page 266 / 357 Scroll up to view Page 261 - 265

Vigor2830 Series User’s Guide

254

Also, you can specify each field for your necessity. It is

recommended for you to use the default settings for VoIP

communication.

Volume Gain

Mic Gain (1-10)/Speaker Gain (1-10)

- Adjust the volume of

microphone and speaker by entering number from 1- 10. The

larger of the number, the louder the volume is.

MISC

Dial Tone Power Leve

l - This setting is used to adjust the

loudness of the dial tone. The smaller the number is, the louder

the dial tone is.

It is recommended for you to use the default

setting.

Ring Frequency

- This setting is used to drive the frequency of

the ring tone. It is recommended for you to use the default

setting.

DTMF

DTMF Mode –

There are four DTMF modes for you to choose.

InBand

-

Choose this one then the Vigor will send the DTMF

tone as audio directly when you press the keypad on the phone

OutBand

-

Choose this one then the Vigor will capture the

keypad number you pressed and transform it to digital form

then send to the other side; the receiver will generate the tone

according to the digital form it receive. This function is very

useful when the network traffic congestion occurs and it still

can remain the accuracy of DTMF tone.

SIP INFO

-

Choose this one then the Vigor will capture the

DTMF tone and transfer it into SIP form. Then it will be sent to

the remote end with SIP message.

Page 267 / 357

Vigor2830 Series User’s Guide

255

Payload Type (rfc2833)

- Choose a number from 96 to 127,

the default value was 101. This setting is available for the

OutBand (RFC2833) mode.

4.12.4 Status

From this page, you can find codec, connection and other important call status for each port.

Refresh Seconds

Specify the interval of refresh time to obtain the latest VoIP

calling information. The information will update immediately

when the Refresh button is clicked.

Port

It shows current connection status for Phone(s) and ISDN ports.

Status

It shows the VoIP connection status.

IDLE -

Indicates that the VoIP function is idle.

HANG_UP -

Indicates that the connection is not established

(busy tone).

CONNECTING -

Indicates that the user is calling out.

WAIT_ANS -

Indicates that a connection is launched and

waiting for remote user’s answer.

ALERTING -

Indicates that a call is coming.

ACTIVE-

Indicates that the VoIP connection is launched.

Page 268 / 357

Vigor2830 Series User’s Guide

256

Codec

Indicates the voice codec employed by present channel.

PeerID

The present in-call or out-call peer ID (the format may be IP or

Domain).

Elapse

The format is represented as hours:minutes:seconds.

Tx Pkts

Total number of transmitted voice packets during this

connection session.

Rx Pkts

Total number of received voice packets during this connection

session.

Rx Losts

Total number of lost packets during this connection session.

Rx Jitter

The jitter of received voice packets.

In Calls

Accumulation for the times of in call.

Out Calls

Accumulation for the times of out call.

Miss Calls

Accumulation for the times of missing call.

Speaker Gain

The volume of present call.

Log

Display logs of VoIP calls.

4.13 Wireless LAN

This function is used for “n” models only.

4.13.1 Basic Concepts

Over recent years, the market for wireless communications has enjoyed tremendous growth.

Wireless technology now reaches or is capable of reaching virtually every location on the

surface of the earth. Hundreds of millions of people exchange information every day via

wireless communication products. The Vigor “n” model, a.k.a. Vigor wireless router, is

designed for maximum flexibility and efficiency of a small office/home. Any authorized staff

can bring a built-in WLAN client PDA or notebook into a meeting room for conference

without laying a clot of LAN cable or drilling holes everywhere. Wireless LAN enables high

mobility so WLAN users can simultaneously access all LAN facilities just like on a wired

LAN as well as Internet access.

The Vigor wireless routers are equipped with a wireless LAN interface compliant with the

standard IEEE 802.11n draft 2 protocol. To boost its performance further, the Vigor Router is

also loaded with advanced wireless technology to lift up data rate up to 300 Mbps*. Hence,

you can finally smoothly enjoy stream music and video.

Note

:

*

The actual data throughput will vary according to the network conditions and

environmental factors, including volume of network traffic, network overhead and

building materials.

In an Infrastructure Mode of wireless network, Vigor wireless router plays a role as an Access

Point (AP) connecting to lots of wireless clients or Stations (STA). All the STAs will share the

same Internet connection via Vigor wireless router. The

General Settings

will set up the

information of this wireless network, including its SSID as identification, located channel etc.

Page 269 / 357

Vigor2830 Series User’s Guide

257

Multiple SSIDs

Vigor router supports four SSID settings for wireless connections. Each SSID can be defined

with different name and download/upload rate for selecting by stations connected to the router

wirelessly.

Security Overview

Real-time Hardware Encryption:

Vigor Router is equipped with a hardware AES encryption

engine so it can apply the highest protection to your data without influencing user experience.

Complete Security Standard Selection:

To ensure the security and privacy of your wireless

communication, we provide several prevailing standards on market.

WEP (Wired Equivalent Privacy) is a legacy method to encrypt each frame transmitted via

radio using either a 64-bit or 128-bit key. Usually access point will preset a set of four keys

and it will communicate with each station using only one out of the four keys.

WPA (Wi-Fi Protected Access), the most dominating security mechanism in industry, is

separated into two categories: WPA-personal or called WPA Pre-Share Key (WPA/PSK), and

WPA-Enterprise or called WPA/802.1x.

In WPA-Personal, a pre-defined key is used for encryption during data transmission. WPA

applies Temporal Key Integrity Protocol (TKIP) for data encryption while WPA2 applies AES.

The WPA-Enterprise combines not only encryption but also authentication.

Since WEP has been proved vulnerable, you may consider using WPA for the most secure

connection. You should select the appropriate security mechanism according to your needs.

No matter which security suite you select, they all will enhance the over-the-air data

protection and /or privacy on your wireless network. The Vigor wireless router is very flexible

and can support multiple secure connections with both WEP and WPA at the same time.

Separate the Wireless and the Wired LAN- WLAN Isolation

enables you to isolate your

wireless LAN from wired LAN for either quarantine or limit access reasons. To isolate means

neither of the parties can access each other. To elaborate an example for business use, you

may set up a wireless LAN for visitors only so they can connect to Internet without hassle of

the confidential information leakage. For a more flexible deployment, you may add filters of

MAC addresses to isolate users’ access from wired LAN.

Page 270 / 357

Vigor2830 Series User’s Guide

258

Manage Wireless Stations - Station List

will display all the station in your wireless network

and the status of their connection.

Below shows the menu items for Wireless LAN.

4.13.2 General Setup

By clicking the

General Settings

, a new web page will appear so that you could configure the

SSID and the wireless channel. Please refer to the following figure for more information.

Enable Wireless LAN

Check the box to enable wireless function.

Mode

At present, the router can connect to 11n Only, 11g Only, Mixed

Rate

Popular DrayTek Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share